Log in

View Full Version : can someone meausre their stock or a/m header?


thebarber
12-14-2008, 08:53 PM
wondering if this dc sports header i bought for an xb/xa will fit on my yaris....

need some measurements from an oem yaris header or aftermarket yaris header...

im getting about 8.25" from the front of the flange that would connect to the block to the midpipe flange (see pic below). and about 6.5" from the center of the runners to the center of the exhaust/midpipe pipe (see pic below). and the midpipe flange seems to +/- line up w/ the 2nd runner on the block flange....

also, just take a look at the pics i have to see if your oem/aftermarket header is similar in angle....

post pics of your yaris header if you can, please

http://i22.photobucket.com/albums/b339/dabarber/yaris/dc%20header%20xa%20xb/echodcheader011.jpg

http://i22.photobucket.com/albums/b339/dabarber/yaris/dc%20header%20xa%20xb/echodcheader005.jpg

http://i22.photobucket.com/albums/b339/dabarber/yaris/dc%20header%20xa%20xb/echodcheader009.jpg

http://i22.photobucket.com/albums/b339/dabarber/yaris/dc%20header%20xa%20xb/echodcheader008.jpg

http://i22.photobucket.com/albums/b339/dabarber/yaris/dc%20header%20xa%20xb/echodcheader007.jpg

http://i22.photobucket.com/albums/b339/dabarber/yaris/dc%20header%20xa%20xb/echodcheader004.jpg

http://i22.photobucket.com/albums/b339/dabarber/yaris/dc%20header%20xa%20xb/echodcheader003.jpg

cali yaris
12-14-2008, 08:56 PM
doesn't look right to me -- I have a stock header I can measure tomorrow morning @ work.

PHXDEMON
12-14-2008, 10:19 PM
This has already been covered. It will bolt to the engine fine but it won't meet up with the midpipe iirc.

ddongbap
12-14-2008, 11:41 PM
whats IIRC mean? I always ask, I always get an answer, but I always forget.

taKuto
12-15-2008, 12:12 AM
'if i recall correctly'
i'm still pissed off at the guy you bought it from, i wasted so much time trying to organize to pick it up from him since he was discussing shipping with me and then tells me he's selling to someone else. :mad:

ztrack157
12-15-2008, 12:58 AM
Sell it of scion life and put it towards one that fits. I measured my stock header for you and no numbers add up to what you get with the DC you have.

cleong
12-15-2008, 04:08 AM
If you're prepared to hack off one or more of your catalytic converters and weld in a section of replacement pipe angled to suit the DC, you could make it fit.

But there's no turning back for this one though.

cali yaris
12-15-2008, 05:36 PM
thebarber,

your 6.5" vertical is about 5" on the stock header, and your 8.25" front to back is about 11" on the stock header.

The angle at the end is completely different.

thebarber
12-15-2008, 07:13 PM
thebarber,

your 6.5" vertical is about 5" on the stock header, and your 8.25" front to back is about 11" on the stock header.

The angle at the end is completely different.

thanks garm, appreciate it