ECU Wiring Diagram?

[thebarber]

anyone have the ecu diagram for an 07 yaris hatch? searched, but can't find it...

[BLH]

Closest I have seen is in section 5 of the EWD.PDF file part of the service manual. I downloaded from a thread here.

[thebarber]

http://www.etimago.com/yaris/repairmanual/

thanks to etimago for this one...

[CTScott]

Here's a chart that I put together. The connector pinouts are at the end of the EWD. I went through the EWDs to figure out every used pin on the two connectors.

In case you are wondering about the highlighting - They are the pins needed to fire up and ECM on the bench. The ones highlighted in red are the ones that need +12V and the yellows are the ones that need to be grounded.

28413

[AlexNet0]

wow, very nice!!

[tk-421]

Well done CTScott!
Much :respekt:

[miketrd]

Hellow all

I bought an 1nz-fet - NCP13 Vitz TRD engine with turbo from yahoo jpctrade auction.

By trying to put the motor on my car we found the following problem: The 2 sockets with wire from ecu to car speedometer are missing. I attach a photograph (111.jpg) to show the missing sockets.

http://i1199.photobucket.com/albums/aa467/mbasil7/111.jpg

So we found 2 sockets which match but we haven't the terminals of ecm (ecu pinout - wiring diagram) to construct the cables.

In addition to the above my car is Toyota Yaris TS 1.5- NCP13 2002 and the vitz trd engine is from a vitz rs turbo 2003 model (facelift). So the 2 harnesses are different.

I want to ask you someone have the pinout diagram for this or where could i find it?

Thanks in advance

[sleey0]

^^

Goo luck finding that. Ouch.....

[CTScott]

Hellow all

I bought an 1nz-fet - NCP13 Vitz TRD engine with turbo from yahoo jpctrade auction.

By trying to put the motor on my car we found the following problem: The 2 sockets with wire from ecu to car speedometer are missing. I attach a photograph (111.jpg) to show the missing sockets.


So we found 2 sockets which match but we haven't the terminals of ecm (ecu pinout - wiring diagram) to construct the cables.

In addition to the above my car is Toyota Yaris TS 1.5- NCP13 2002 and the vitz trd engine is from a vitz rs turbo 2003 model (facelift). So the 2 harnesses are different.

I want to ask you someone have the pinout diagram for this or where could i find it?

Thanks in advance

I think I have everything that you need. PM me your email address and I'll email you the pdf's.

[sleey0]

CT just has every wring scheme imaginable!!!

You keep on surprising me:)

[happyshadrack@gmail.com]

I think I have everything that you need. PM me your email address and I'll email you the pdf's.

CT please send me the same PDF. I have the same problem here with a new engine

[happyshadrack@gmail.com]

Hellow all

I bought an 1nz-fet - NCP13 Vitz TRD engine with turbo from yahoo jpctrade auction.

By trying to put the motor on my car we found the following problem: The 2 sockets with wire from ecu to car speedometer are missing. I attach a photograph (111.jpg) to show the missing sockets.

http://i1199.photobucket.com/albums/aa467/mbasil7/111.jpg

So we found 2 sockets which match but we haven't the terminals of ecm (ecu pinout - wiring diagram) to construct the cables.

In addition to the above my car is Toyota Yaris TS 1.5- NCP13 2002 and the vitz trd engine is from a vitz rs turbo 2003 model (facelift). So the 2 harnesses are different.

I want to ask you someone have the pinout diagram for this or where could i find it?

Thanks in advance

please forward me the pdf from CT if you can, bought a new enine with the same problem

[Kaws Wong]

HI MAte,

I have the same problem also, would you please forward pdf diagram also?

Thank for your help.
BR.
Kaws

[Juan Perez]

does anyone have the diagram?
Could tell me where i can find it

Just build a yaris TS with turbo and need the pinout diagram for the ECU vitz turbo (1nz-fet - NCP13 Vitz TRD)

thanks

[Sd2jza70]

I’m in need of the diagram for the 1NZ-FET trd Turbo ecu if anybody would be so kind as to share it :)

[Huevito]

In need of the diagram for the 1nz turbo also can someone help if anyone is still out there?

[Yousefzaid]

Anybody knows which programmer use to program a 2023 yaris with a M [4A] blade key I'm need make replacement key