New stereo for Yaris 2004 query.

[llama]

Ive got a 1.4 D4-D yaris and id like to change the stereo however i cant find any new fascias for my model (2004)

Does anyone know from where i could purchase one? its very similar to the one below however theres a small cash box on the bottom left and the cigarette lighter is on the right:

http://cgi.ebay.co.uk/TOYOTA-YARIS-CHANGE-YOUR-RADIO-FOR-AFTERMARKET-FASCIA_W0QQitemZ190346314358QQcmdZViewItemQQptZUK_ CarsParts_Vehicles_FasciaPlates_SM?hash=item2c5186 4276

i could simply install a new stereo in the bottom try however i think it would look stupid having 2 stereos on top of each other!! i would like my stereo looks like the one below (mine is exactly like this one, except the stock stereo is installed instead):

http://www.toyotaownersclub.com/forums/uploads/1104279348/gallery_8688_40_1104417266.jpg

Thanks!!

Llama :D

[IllusionX]

it's kinda hard to find that part in other countries as this model came with integrated radios and was not sold in USA.


anyhow.. this will fit your vehicle..

http://cgi.ebay.com/ebaymotors/Car-Radio-Dash-Kits-Toyota-Echo-00-01-02-03-2000_W0QQcmdZViewItemQQhashZitem4a83ec9e8cQQitemZ3 20040902284QQptZCarQ5fAudioQ5fVideo

[CTScott]

Take a look at the following thread:

http://www.yarisworld.com/forums/showthread.php?t=17393&highlight=radio

[llama]

ok thanks :D

[llama]

however is the link i sent (1st one) enough? and would i need the ISO adapter?

[CTScott]

however is the link i sent (1st one) enough? and would i need the ISO adapter?

I can't tell from the picture in your 1st link if the radio hole is the correct width for an aftermarket radio or if the ISO adapter would be required to make fill the gap on the sides of the radio.

[llama]

I can't tell from the picture in your 1st link if the radio hole is the correct width for an aftermarket radio or if the ISO adapter would be required to make fill the gap on the sides of the radio.

The aftermarket stereo will fit in for sure. what id like to know is:

After buying this could i just slip in my aftermarket stereo
Do i need the ISO adapter (as far as i know its that cable that u use to connect the stock wires to connect and aftermarket stereo)


Thanks again :)

[IllusionX]

you do not need the iso mount for the dash kit i showed you. It has screw holes and should fit just right in.

[llama]

you do not need the iso mount for the dash kit i showed you. It has screw holes and should fit just right in.

Yes however i dont think it would fit. see my stereo looks somewhat like this one:

http://www.fitaudio.com/storedimages/toy_yaris/headunit1.jpg

a newer version, though it seems its extremely similar! so ders no way u cud fit that in because theres the old stereo blocking it and even if u pulled it out i would look really bare wudnt it?

[CTScott]

Yes however i dont think it would fit. see my stereo looks somewhat like this one:

http://www.fitaudio.com/storedimages/toy_yaris/headunit1.jpg

a newer version, though it seems its extremely similar! so ders no way u cud fit that in because theres the old stereo blocking it and even if u pulled it out i would look really bare wudnt it?

You definitely need the replacement face piece for the dash (like the one in your first post). The question is if the replacement piece has an opening that is 180mm wide (standard DIN radio width) or 200mm (a wider width common with non-integrated Toyota radios). If the replacement trim piece has a 180mm wide opening, then that and the wiring adapter is all you need. If the replacement trim piece has a 200mm wide opening, then you also need a kit that adapts the opening to the correct width for an aftermarket radio.

[llama]

You definitely need the replacement face piece for the dash (like the one in your first post). The question is if the replacement piece has an opening that is 180mm wide (standard DIN radio width) or 200mm (a wider width common with non-integrated Toyota radios). If the replacement trim piece has a 180mm wide opening, then that and the wiring adapter is all you need. If the replacement trim piece has a 200mm wide opening, then you also need a kit that adapts the opening to the correct width for an aftermarket radio.

Thanks a lot then :)

[IllusionX]

cept that replacement face piece for the dash is impossible to find, at least, that i know of, in Europe.