DIY Cruise Control for 2012 Yaris - Good News!

[CTScott]

I recently obtained the wiring diagrams for the 2012 Yaris. Much of the wiring and connectors remain the same as the second generation Yaris. This is the case for cruise control, so 2012 Yaris owners can DIY cruise control using the same OEM stalk.

For the 2012 the wiring is the same as that of the 2009-2011 Yaris, where the wiring from the ECM to the steering column is (theoretically) there. Also, the 2012 Yaris has the cruise control "On" and "Set" indicators built into the instrument cluster.

For those with the steering wheel audio controls the spiral cable connector, under the airbag, is a 10 pin connector, instead of a 4 pin connector (like those without steering audio controls and that of the 2006-2011 Yaris).

44502

Those with the audio controls will need to transfer the two cruise control pins (in positions 1 and 2) from the 4 pin cruise control stalk wire to their 10 pin spiral cable connector (in positions 1 and 2).


The procedure for removing the steering wheel airbag is a little different for the 2012, where three clips secure the airbag to the steering wheel (rather than 2 screws like the 2006-2011 Yaris).

44503


Also, for the 2012, the lower steering wheel cover has a separate removable cover section for where the cruise stalk goes through, called the "lower no. 2 steering wheel cover"

44504


If someone from the Connecticut area is interested in adding cruise control to their 2012 Yaris, I have the parts and would be more than willing to help to give me the opportunity to document the process and update my Cruise Control DIY.

[Shinare]

Ewe Rok!!!

[Chuck G]

Ewe Rok!!!
absolutely!!

[bs_ane]

can you give more details about ,how we can make the cruise control???

[CTScott]

can you give more details about ,how we can make the cruise control???

Below is the link to my DIY for 2006-2011 US and Canadian Yaris. For the second generation Yaris it was very easy to add cruise control to US and Canadian Yaris, since the ECM had the function built in.

For European Yaris it was not built in, so a complete aftermarket system was necessary. My understanding for the new third generation European Yaris is that cruise control is now an option.

http://www.yarisworld.com/forums/showthread.php?t=33750

[bronsin]

The cc mod on my 09 Yaris is still going strong! Plus I get chops when I tell people cc is built into the ECM.

I just bought a 2001 Corvette and of course it has the stalk cc.

I much prefer the four buttons on my dash on the Yaris!

[motoman740]

Hello, this is my first post here in yaris world. I just purchased a 2012 yaris. I dont have any radio buttons on the steering wheel. I assume I have the 4 pin connector, so everything should plug in and work? Also, where do I get the parts to do the cruise control mod?

[CTScott]

Hello, this is my first post here in yaris world. I just purchased a 2012 yaris. I dont have any radio buttons on the steering wheel. I assume I have the 4 pin connector, so everything should plug in and work? Also, where do I get the parts to do the cruise control mod?

I have the stalk with wiring and mounting screws available for $40 shipped. I shipped a set to mr9865 on here, but he just picked his 2012 up yesterday, so I don't think he's gotten around to testing it out yet.

[mr9865]

thinking about doing it now!

[CTScott]

thinking about doing it now!

Hopefully you have a camera handy with decent macro capability, so we can document the 2012 install.

[mr9865]

I can if i find batteries

[mr9865]

looks like this is above my head. cant even find the airbag clips

[CTScott]

looks like this is above my head. cant even find the airbag clips

If you pop off the little cover on the side of the steering wheel, you should be able to take a peek inside to get a better feel for where the clips are.

[motoman740]

Sounds pretty straight forward:

-Disconnect the battery for 30 min before touching anything
-Remove the steering wheel side cover
-Pop off the 3 air-bag clips(if you disconnect the airbag I think the ABS light will turn on)
-Connect and install the cruise control stalk to the 4 pin connector
--If you have steering wheel controls for the radio then transfer the 2 wires from the cruise stalk to the 10 pin connector
-Put everything together and cross your fingers

[CTScott]

Sounds pretty straight forward:




Indeed. the tricky thing is just figuring out the airbag removal, as it is different from the 2nd gen Yaris, with the clips instead of screws.

With the light piece that you mentioned above, I think you meant SRS, not ABS light. But, if you disconnect and reconnect the airbag connectors with the battery disconnected the SRS will not log a DTC and turn the light on. If you were to do it with power, or connect the battery to test the cruise before reconnecting the airbag, then you would get the SRS light.

[motoman740]

Indeed. the tricky thing is just figuring out the airbag removal, as it is different from the 2nd gen Yaris, with the clips instead of screws.

With the light piece that you mentioned above, I think you meant SRS, not ABS light. But, if you disconnect and reconnect the airbag connectors with the battery disconnected the SRS will not log a DTC and turn the light on. If you were to do it with power, or connect the battery to test the cruise before reconnecting the airbag, then you would get the SRS light.

Good to know.
Also, I was looking at the steering wheel yesterday and I think the clips just hold it in place, and all you need to do is pull the thing straight out.

[CTScott]

Good to know.
Also, I was looking at the steering wheel yesterday and I think the clips just hold it in place, and all you need to do is pull the thing straight out.

I think that the clips are holding against a groove in a plastic rod. This is the only other image from the service manual, and it looks like those three plastic rods are positioned where the other image shows to press the clips:

44768

[mr9865]

Its just that the base airbag is a little different than the one in your diagrams

[CTScott]

Its just that the base airbag is a little different than the one in your diagrams

I see that now. This is a picture that I snapped when I test drove a 2012 base. Unfortunately with the sales guy breathing down my neck, I wasn't able to poke around as much as I would have liked to. The 2012 base airbag cover looks a whole lot like the 06-11.

Look on the sides of of the lower steering wheel cover for the two holes, where the Torx screws would be on a 06-11.

44776

[motoman740]

ok so i took some pictures of the steering wheel:

http://i247.photobucket.com/albums/gg145/motoman540/Yaris%20Cruise%20Control/P1020026.jpg

The air bag is held on by what looks like 3 or 4 clip style bolts. To remove the air bag you have to insert a small screwdriver and push a metal clip that in turn releases the module. There should be 3 or 4 clips. The removal should be a bit tricky since you have to work your way around to get all loose, but the installation is going to be super easy.

http://i247.photobucket.com/albums/gg145/motoman540/Yaris%20Cruise%20Control/P1020030.jpg

http://i247.photobucket.com/albums/gg145/motoman540/Yaris%20Cruise%20Control/P1020028.jpg

http://i247.photobucket.com/albums/gg145/motoman540/Yaris%20Cruise%20Control/P1020032.jpg

the cover is removed easily by inserting a small key/screw driver in the notch and popping it loose.

http://i247.photobucket.com/albums/gg145/motoman540/Yaris%20Cruise%20Control/P1020036.jpg

http://i247.photobucket.com/albums/gg145/motoman540/Yaris%20Cruise%20Control/P1020040.jpg

http://i247.photobucket.com/albums/gg145/motoman540/Yaris%20Cruise%20Control/P1020034.jpg

The gauge cluster already has the markings for the cruise functions but the lights dont turn on when the ignition is put on. This tells me that probably the bulbs are not installed and the hole is empty, or the ecm doesnt have the cruise control programmed... Its probably the lack of bulbs.

http://i247.photobucket.com/albums/gg145/motoman540/Yaris%20Cruise%20Control/P1020045.jpg

http://i247.photobucket.com/albums/gg145/motoman540/Yaris%20Cruise%20Control/P1020043.jpg

[CTScott]

Thanks for snapping those pics. Even on the 09-11 the CC lights don't light up with the ignition, but they do work once the stalk is in, so I am sure that the 2012 is the same.

[CENTRALDM]

I recently obtained the wiring diagrams for the 2012 Yaris. Much of the wiring and connectors remain the same as the second generation Yaris. This is the case for cruise control, so 2012 Yaris owners can DIY cruise control using the same OEM stalk.

For the 2012 the wiring is the same as that of the 2009-2011 Yaris, where the wiring from the ECM to the steering column is (theoretically) there. Also, the 2012 Yaris has the cruise control "On" and "Set" indicators built into the instrument cluster.

For those with the steering wheel audio controls the spiral cable connector, under the airbag, is a 10 pin connector, instead of a 4 pin connector (like those without steering audio controls and that of the 2006-2011 Yaris).

44502

Those with the audio controls will need to transfer the two cruise control pins (in positions 1 and 2) from the 4 pin cruise control stalk wire to their 10 pin spiral cable connector (in positions 1 and 2).


The procedure for removing the steering wheel airbag is a little different for the 2012, where three clips secure the airbag to the steering wheel (rather than 2 screws like the 2006-2011 Yaris).

44503


Also, for the 2012, the lower steering wheel cover has a separate removable cover section for where the cruise stalk goes through, called the "lower no. 2 steering wheel cover"

44504


If someone from the Connecticut area is interested in adding cruise control to their 2012 Yaris, I have the parts and would be more than willing to help to give me the opportunity to document the process and update my Cruise Control DIY.

I bought new yaris 2012 in South Africa and i want install cruise control. where can I get all the spare parts?The car has got all the radio bluetooth buttons on steering wheel. Can you help me. I dont want to install aftermarket unit.

[CTScott]

I bought new yaris 2012 in South Africa and i want install cruise control. where can I get all the spare parts?The car has got all the radio bluetooth buttons on steering wheel. Can you help me. I dont want to install aftermarket unit.

Hopefully I can help. The first question is if the ECM on your Yaris has the cruise control function built in. If you could PM me the VIN number of your car, I can run it through the international EPC to see if it does.

[CENTRALDM]

Where can I contact you to get the spare parts. From which model can I bought it? Please help? Danie from South Africa.

[CTScott]

Where can I contact you to get the spare parts. From which model can I bought it? Please help? Danie from South Africa.

I PMed you back regarding some additional information that I will need to determine if the ECM on your Yaris has the cruise control function built in.

[CTScott]

I'm still looking for someone around the Connecticut area that is interested in having cruise control installed on their 2012 Yaris.

I shipped a stalk to a gentleman from South Africa, who successfully installed it on his Yaris, but he had a tough time with figuring out how to remove the airbag. I believe that from the pictures that he sent me, that I now have a good grasp of how to do so, but I would like to get it documented to make it easy for anyone who wants to DIY cruise control to do so.

[Crandall]

Scott; do you think the clockspring from the 2012's would work in the previous generation? I would love to have cruise and audio controls.

[CTScott]

Scott; do you think the clockspring from the 2012's would work in the previous generation? I would love to have cruise and audio controls.

My bet is that it will fit and it does have the extra wires necessary to allow for both cruise and steering wheel controls.

[Crandall]

My bet is that it will fit and it does have the extra wires necessary to allow for both cruise and steering wheel controls.

I guess I'll have to order one and see if it indeed does.

[12BusYaris]

I shot a few photos showing the pins and how to access them to remove the air bag/horn button. Just a note - I turned the steering wheel for easier access to the pins (thus photos show upside down). I never diconnected the airbag as it will rest on the steering wheel and allow easy access to install the stalk and connections.

Jay

[richard_rsp]

Thank You! Those pictures help dramatically in understanding the process and the method for accessing the pins! I got mine in the mail earlier today and will let everyone know how it goes! :)

EDIT: Ok, just went and installed mine on my 2012 Yaris L. VERY EASY. Bad news: It doesn't work. The Green light comes on, however, it will not set at a speed. I have a distinct feeling that the clutch switch is not on the 2012 Yaris L... I looked under the dash and did not see a switch, except for the starter safety switch; there was only a bolt to stop the clutch from coming up.

EDIT 2: Ok, I have confirmed that my 2012 Yaris L (3-door) does NOT have the cruise control clutch switch. All of the wiring is there (including the harness connector) but the actual switch is absent. I was able to jump the pins on the connector (THanks CTScott!) and the cruise worked fine. So, if anybody is adding cruise control to their 2012 Yaris L (Manual Tranny, of course), it looks like we will need to install the clutch switch. (Hey, at least all the wiring is there! :-) )

Also turned the wheel upside down for better access
http://img.photobucket.com/albums/v108/richard_rsp/15603c22.jpg

3 Clips
http://img.photobucket.com/albums/v108/richard_rsp/7eda76b5.jpg

http://img.photobucket.com/albums/v108/richard_rsp/1d20fd2d.jpg

http://img.photobucket.com/albums/v108/richard_rsp/3e7f441c.jpg

http://img.photobucket.com/albums/v108/richard_rsp/0b59a62a.jpg

http://img.photobucket.com/albums/v108/richard_rsp/c7cae958.jpg

http://img.photobucket.com/albums/v108/richard_rsp/492635d7.jpg

http://img.photobucket.com/albums/v108/richard_rsp/2184110c.jpg

Here is under the dash where the "clutch switch" should be
http://img.photobucket.com/albums/v108/richard_rsp/e9562679.jpg

[CTScott]

Thanks for all of the pictures gentlemen! This will now allow me to put together a proper step by step DIY for the 2012.

[Slasher]

Thanks CTScott,:bow:

The pics of the airbag clips made it super simple!!! I only had one real problems and that was removal/install of the horn pin on the old 4 pin connector... I broke it!!! I tried to force it!!! It's ALL MY OWN FAULT!!!! The removing the pin was almost impossible as there isn't a pin unlock like anything in the picture...

Well except for not having a horn, it works great on my 2012 3dr L 5spd:thumbup:

Also the lower dash panel under the steering wheel has an airbag, so that meant getting down on the ground and contorting myself to look under but the clutch switch was really easy to instal. The biggest bear was trying to pull off the tape from the harness to drop the connection for the clutch switch...

I just got back from the test drive and a refill... So 2 tanks and I am averaging 41.6 mpg I am pleased as I am still running 32psi in the tires and running A/C!!!

I am sure the CC will make the commute more tolerable... The aero hubcaps are enroute... And the next upgrade will be the speakers...

[CTScott]

Thanks CTScott,:bow:

The pics of the airbag clips made it super simple!!! I only had one real problems and that was removal/install of the horn pin on the old 4 pin connector... I broke it!!! I tried to force it!!! It's ALL MY OWN FAULT!!!! The removing the pin was almost impossible as there isn't a pin unlock like anything in the picture...

Well except for not having a horn, it works great on my 2012 3dr L 5spd:thumbup:

Also the lower dash panel under the steering wheel has an airbag, so that meant getting down on the ground and contorting myself to look under but the clutch switch was really easy to instal. The biggest bear was trying to pull off the tape from the harness to drop the connection for the clutch switch...

I just got back from the test drive and a refill... So 2 tanks and I am averaging 41.6 mpg I am pleased as I am still running 32psi in the tires and running A/C!!!

I am sure the CC will make the commute more tolerable... The aero hubcaps are enroute... And the next upgrade will be the speakers...



I apologize for the broken pin issue. For 2006-2011 Yaris I ship the harness with the horn wire installed. After the last couple of 2012 installs I didn't think that I needed to include it, as the horn wire was on the other connector, but as it turns out that is only for 2012's with steering wheel audio controls. For ones without the horn wire is still on the 4 pin connector where the cruise control connects through.

[Slasher]

I apologize for the broken pin issue. For 2006-2011 Yaris I ship the harness with the horn wire installed. After the last couple of 2012 installs I didn't think that I needed to include it, as the horn wire was on the other connector, but as it turns out that is only for 2012's with steering wheel audio controls. For ones without the horn wire is still on the 4 pin connector where the cruise control connects through.

Scott,
I am happier than a pig in poop!!! I should have been able to do it, but these Yota pins are unlike many of the pins I've messed with... It looked simple, but I am sure there's a trick to em...

[Frank Necrosis]

Ordered the parts from CTScott, got them quickly.

The install was relatively simple. It took me about 15 minutes. Everything works perfectly.

Thanks CTScott!!!!

[stuart_f]

Also ordered from CTScott and got the parts in UK very quickly and no customs issues (despite USPS tracking saying the package is still in USA!)

I notice my steering wheel assembly is slightly different from Richard_RSP's (but thank you for the pictures that helped a lot in knowing what I was aiming for.

I have the steering wheel audio and also the bluetooth telephone control on my UK Spec 2012, 1.33 Yaris TR Auto (not sure which bit of that means I have the different clips though!)

Also, pin 1 & 2 of the 10-pin connector are already occupied so I put the cruise in the spare 4-pin socket next to it.

Edit- It works!

[CTScott]

Excellent! I am glad to see that the installation went well.

[macoloco]

hi...i'm just reading all posts, but i have a question..

are you always talking about 1.33 VVTI, right?

is it possible to have cruise control in a 1.4 D4D 2012 yaris ??

[CTScott]

hi...i'm just reading all posts, but i have a question..

are you always talking about 1.33 VVTI, right?

is it possible to have cruise control in a 1.4 D4D 2012 yaris ??

Correct - According the the wiring diagrams for the European Yaris, only the Yaris with the 1NR-FE (1.33L) support OEM cruise control. Ones with the D4D would need an aftermarket cruise control solution.

[macoloco]

Thank u very much....
Its a pity....:(

[b20vteg]

hey there scott, got anymore stalks left? i'd love to pick one up from ya...

[CTScott]

hey there scott, got anymore stalks left? i'd love to pick one up from ya...

I sure do. I'll PM you the details.

[Jamus]

I'm working on installing the 2-button cruise control on my 2012 L automatic. I am having trouble identifying the correct wires to connect to. On the 06-11 D3 plug there is a black wire, and then a blue and brown wire if you have the correct wiring to the computer. Here's a pic I took from under my steering column. If I were to assume, I'd say it's still the brown and blue wires on the plug next to the yellow one. But I'd rather double check with you guys who know.

Link to the type of cruise control mod I'm using.
http://www.yarisworld.com/forums/showthread.php?t=17158

[CTScott]

I'm working on installing the 2-button cruise control on my 2012 L automatic. I am having trouble identifying the correct wires to connect to. On the 06-11 D3 plug there is a black wire, and then a blue and brown wire if you have the correct wiring to the computer. Here's a pic I took from under my steering column. If I were to assume, I'd say it's still the brown and blue wires on the plug next to the yellow one. But I'd rather double check with you guys who know.

Link to the type of cruise control mod I'm using.
http://www.yarisworld.com/forums/showthread.php?t=17158

For the 2012, the CCS wire (formerly blue) is now beige and the ground wire (formerly brown) is still brown. They are the two left most wires on the black connector to the left of the yellow airbag connector.

[Jamus]

Awesome, thank you very much. I never would have guessed it to be the black plug.

[Jamus]

Well, I tried to hook this up with no result. I'm partially color blind so maybe I could have the wrong wires. Is there a diagram of the black plugs pins somewhere? Is there a black wire, or a dark brown?

[CTScott]

Well, I tried to hook this up with no result. I'm partially color blind so maybe I could have the wrong wires. Is there a diagram of the black plugs pins somewhere? Is there a black wire, or a dark brown?

This is the connector drawing (view is looking into the holes where the connector would plug into the clockspring). Pin 1 (beige) is the CCS pin, which goes to the ECM. Pin 2 (Brown) is the ground wire.

48265

[Jamus]

Thanks for the quick response, and expert electrical knowledge. I used a micro pot instead of resistors. That shouldn't be a problem should it?

[CTScott]

Thanks for the quick response, and expert electrical knowledge. I used a micro pot instead of resistors. That shouldn't be a problem should it?

The problem with potentiometers is that depending on the construction they can drift. Also, depending on the range of the pot, the under 1K area of the pot can be very small, making it difficult to lock in the correct values.

[Jamus]

Just wanted to let everyone know I got it working and it's great. I probably ran into every problem that one might run into, but with quick help from CTScott I was put back on the right track. Thanks again Scott, and the forum as a whole.

[PierreG]

Got the cruise stalk in my 2012 3dr., but does anyone know where there is a tutorial to get at the clutch switch?

[CTScott]

Got the cruise stalk in my 2012 3dr., but does anyone know where there is a tutorial to get at the clutch switch?

The clutch switch on the 2012 is just like the 2nd gen. Look at the top of the clutch pedal and you will see a bolt threaded into the frame, with a stop nut where it meets the frame. Remove that bolt and install the CC clutch switch in its place. The switch should be adjusted to where it is fully pressed in when the clutch pedal is not depressed and, where as soon as you touch the pedal the switch is no longer pressed.


49099

[danieldk]

Does anyone know how to access the other 2 clips if you have shift paddles ?
( 2012 1.3 Xr CVT 5Dr )

I found the access hole on the bottom, but none on the sides
some images for clarity : The driver view
http://i.imgur.com/Rkapyl.jpg (http://imgur.com/Rkapy)

The access hole on the bottom:
http://i.imgur.com/ruSnil.jpg (http://imgur.com/ruSni)

Left paddle ( gear down):
http://i.imgur.com/rJS89l.jpg (http://imgur.com/rJS89)

Right paddle ( gear up ) with the Cruise control cover thing removed
http://i.imgur.com/bZlbOl.jpg (http://imgur.com/bZlbO)

[stuart_f]

Hi Danieldk,

Have a look at post 37. I have the paddles and had the same issue with getting to the 2 clips at the top of the wheel.

What you have to do is use the hole to push the bottom clip which should release part of the airbag. There are no other holes to get to the other clips so you have to get to them through the gap you create when you release the first clip.

The major thing you have to notice is that the bottom clip (the one you get to through the hole) needs you to push the clip to release it, the other 2 need you to pull. I used a small ring-ended spanner to pull the other clips and release them.

Let me have a go in paint and try and illustrate what you need to do:

Step 1 - push the first pin through the hole with a flat screwdriver. It's the yellow arrow.

Step 2+3 - pull the far away end of the second and third clip towards you. These are circled red in the diagram (sorry about the cables being in the way on the photo of the lower clip but it's just the same as the upper one)

[danieldk]

That makes a lot of sense, Thank you for the diagram, :thumbup:

Now I'll just have to wait for the kit to get here ( might try a few practice runs to get familiar with it.

[danieldk]

Yay,
Got my CC in lever in the post today, and installed it,
Thanks CTScott ! :bow:
http://i.imgur.com/XmqEV.png
getting the last clip undone was a bit of a mission,
I eventually levered up the one side and slid the clip out completely, so the airbag/horn assembly came off nicely, plugged the 4 pin plug into the open receptacle, and went for a drive, :)

plugged in:
http://i.imgur.com/6wQDIl.jpg[/IMG]"] ("http://i.imgur.com/ehnaJl.jpg

Driving with CC set :
http://i.imgur.com/VJhPMl.jpg


also decided to remove my AC control and change the AC light from orange ( AC should make cool and thus not have a warm light ):
I'll take more pictures and post it in another topic..
http://i.imgur.com/AZDerl.jpg

Strangely ( i think ) the AC and rear window heater have LEDs lighting them, but the rest of the lights that light that panel orange are incandescent lamps with a little rubber orange condom like thing over them, one would have expected to see amber LEDs, not incandescent lamps.. :P

[mr_miles]

This makes me wonder if the Rostra CC install is the same for the 2012/13 as it is in the second gen. I yanked it all out of my 08 to put in the new one, just haven't gotten around to finding install guides for it, lol

[CTScott]

This makes me wonder if the Rostra CC install is the same for the 2012/13 as it is in the second gen. I yanked it all out of my 08 to put in the new one, just haven't gotten around to finding install guides for it, lol

Did you have the Rostra with the little stalk on the left side of the wheel, or the Rostra kit which used the OEM right side stalk?

[mr_miles]

i have the kit with the stalk on the left side.

[CTScott]

i have the kit with the stalk on the left side.

Ah. That will probably still work, but really isn't worth the effort. With the 2012, you can simply install the OEM stalk and be good to go (without all of the crazy wiring required for the Rostra kit). If you are interested, I would trade you one of the OEM stalk kits for your Rostra kit, so I can experiment with it to see if it would really work for 2nd gen European owners (I have suspected for quite some time that it will, but have not had the opportunity to verify).

[mr_miles]

Hmm...I do plan on replacing the steering wheel in the future (not near), if you think it's possible to somehow use the OEM cruise with an aftermarket wheel, I wouldn't mind the swap at all.

[CTScott]

Hmm...I do plan on replacing the steering wheel in the future (not near), if you think it's possible to somehow use the OEM cruise with an aftermarket wheel, I wouldn't mind the swap at all.

The OEM one will definitely not work with an aftermarket wheel. The Rostra one will, since it mounts to the steering column cover, rather than within the wheel.

[mr_miles]

Oh well, I'll just go with the OEM until I swap wheels. then I can always adapt to something different later on. You're going to have a box full of Yaris electrical goodies from me, lol. Still have a few other things to send to you :p

[CTScott]

Oh well, I'll just go with the OEM until I swap wheels. then I can always adapt to something different later on. You're going to have a box full of Yaris electrical goodies from me, lol. Still have a few other things to send to you :p

LOL. Sounds like a plan.

[william7]

Hi,

is any chance to work CC in Yaris made in France with 1.0 vvti 1kr-fe engine?

I can get VIN if it could help...

Best regards

[CTScott]

Hi,

is any chance to work CC in Yaris made in France with 1.0 vvti 1kr-fe engine?

I can get VIN if it could help...

Best regards

The Toyota OEM cruise control definitely will not work with the 1.0L French made Yaris, but the Rostra kit that mr miles and I were discussing above may. Once I have it in hand and check some things relative to the wiring diagrams for the 1kr-fe I will let you know.

[william7]

I looked in my yaris speedometer and it has a CC lights.

[CTScott]

I looked in my yaris speedometer and it has a CC lights.

Is it a 2007 Terra, like your info shows, or is it a 2012?

Also, it may be that the same speedometer is used on the 1.0 L and 1.33 L Yaris.

[william7]

I forgot about changing my profile.

I have 2012 Yaris Luna 1.0 L

[CTScott]

I forgot about changing my profile.

I have 2012 Yaris Luna 1.0 L

OK - That makes more sense as to why it has the light for cruise control. According to the Toyota wiring diagrams for the French made Yaris, only the 1.33L has the cruise control function built in, so it must be that they use the same speedometer for the various engine configurations.

[jelo]

Just picked up my 2013 Yaris - will want to do this down the road, so it is time to ask: Anybody know the differences between 2012 and 2013 for cruise control install?

[CTScott]

Just picked up my 2013 Yaris - will want to do this down the road, so it is time to ask: Anybody know the differences between 2012 and 2013 for cruise control install?

No difference at all.

[jelo]

Great - Thanks!

[ksejrs]

Thank you CTScott, richard rsp & 12BusYaris,
I just recently bought my second Yaris(2012). My daughter took the first one (2009) to college. I was disappointed that it didn't have cruise control seeing as it had all the other power options. I was thrilled when I found this site and learned how easy it was to remedy. I bought the stalk online for about $58 with shipping and it took about 30 minutes tops to install. Just need to cut the hole in the cover piece. Anyone have measurements for that? Thanks again!

[CTScott]

Thank you CTScott, richard rsp & 12BusYaris,
I just recently bought my second Yaris(2012). My daughter took the first one (2009) to college. I was disappointed that it didn't have cruise control seeing as it had all the other power options. I was thrilled when I found this site and learned how easy it was to remedy. I bought the stalk online for about $58 with shipping and it took about 30 minutes tops to install. Just need to cut the hole in the cover piece. Anyone have measurements for that? Thanks again!

I still haven't had a chance to get my hands on a 2012 to take the measurements. I actually have a batch of the 2012+ cover pieces on order, and should have them in hand next week.

Also, with the cruise control stalks and the clutch switches, I always have some on hand and sell them for a fraction of retail.

[dennismr]

Got my CC stalk from CTScott 2 weeks ago, but a family emergency kept me from installing it until now.

Got home from work just before 7pm tonight, parked in the garage and popped the hood of my 2013 Yaris L automatic in Absolutely Red so I could disconnect the negative terminal of the battery before I removed the air bag from the steering wheel. Went upstairs, changed my clothes, and started the install...

http://sea-pines.net/yaris/yaris1.jpg
http://sea-pines.net/yaris/yaris2.jpg

Parked with the steering wheel upside to make removing the airbag easier.

http://sea-pines.net/yaris/yaris3.jpg

Removed the lower#2 steering wheel cover (on side of steering wheel), and then pushed in the 3 pins that hold the airbag, as described in other threads, and the airbag pops off very easily. Took a couple of minutes to find the pins, but easy once I did find it.

http://sea-pines.net/yaris/yaris4.jpg

Located the horn wire, and removed it. Placed it aside, as it won't be needed anymore.

http://sea-pines.net/yaris/yaris5.jpg

Pulled the CC stalk out of the box that it was mailed in

http://sea-pines.net/yaris/yaris6.jpg

Slide it into where the lower#2 steering wheel cover was removed, and screw the 2 screws in to hold it in place.

http://sea-pines.net/yaris/yaris7.jpg

Plug the 2 connectors attached to the stalk into the same connectors that I earlier removed the horn wire from.

http://sea-pines.net/yaris/yaris8.jpg

The airbag just pushes back on and clicks into place, and the CC stalk is where it should be...

http://sea-pines.net/yaris/yaris9.jpg

Reconnected the battery, turned the ignition on, turned the CC on, and the dash light turns on just like it should.

http://sea-pines.net/yaris/yaris10.jpg

Took it for a short drive, and everything works exactly like it should. The best $40 investment in this great little car I could make!

The whole process took me from 7:04 pm until 7:25, and that included talking to my neighbor for 5 minutes when he got home from work.

Thanks CTScott and yarisworld!!!

[CTScott]

^Nice!

By the way, I recently acquired a batch of the replacement covers for the side of the 2012-2013 steering wheel, which have the hole for the cruise control stalk. They are $5 shipped in the US.

[misterwolfe]

Can I do this to a 2007 Yaris Liftback with the power option added? I have everything but cruise.

[CTScott]

Can I do this to a 2007 Yaris Liftback with the power option added? I have everything but cruise.

Yes. Below is a link to my DIY for 06-11 Yaris. I carry all of the part required if you are interested in installing it:

http://www.yarisworld.com/forums/showthread.php?t=33750

[misterwolfe]

Yes. Below is a link to my DIY for 06-11 Yaris. I carry all of the part required if you are interested in installing it:

http://www.yarisworld.com/forums/showthread.php?t=33750

Thank you! Though with requiring to wire up my steering column, that may be my roadblock. Will look into this. (I am colorblind, and at the mercy of my father doing these for me.)

If it is relatively easy, I'll totally buy an entire kit from ya. Also, hoping for keyless entry soon too!

[Licky]

Hi everyone, I am new here, and from australia.

I have a Yaris YR 5 door (base model, 1.3 manual)

I have "acquired" a OEM cruise control stalk and cable, I can fit it into the steering wheel no worries, the cruise light comes on, though can not set the speed. Would this be because of the clutch switch?. I have tried Toyota, and they werent really much help. Though they did come back with a $90 part. I do have to push the clutch in to start the vehicle to begin with though, so i would assume it would already have one?.

Could someone please shed some light for me?

THanks.

[CTScott]

Hi everyone, I am new here, and from australia.

I have a Yaris YR 5 door (base model, 1.3 manual)

I have "acquired" a OEM cruise control stalk and cable, I can fit it into the steering wheel no worries, the cruise light comes on, though can not set the speed. Would this be because of the clutch switch?. I have tried Toyota, and they werent really much help. Though they did come back with a $90 part. I do have to push the clutch in to start the vehicle to begin with though, so i would assume it would already have one?.

Could someone please shed some light for me?

THanks.

There are two clutch switches on a manual transmission Yaris. The pre-installed on is the push the clutch to the floor to start the car one. The one you have to add for cruise control works the opposite way. It replaces the stopper bolt that the clutch arm rests against (when your foot is not on it) and it signals the ECM when you barely touch the clutch pedal (to prevent the revving that would occur if the clutch was pressed when cruise was applying throttle).

[geoded]

[QUOTE=CTScott;615019]I recently obtained the wiring diagrams for the 2012 Yaris. Much of the wiring and connectors remain the same as the second generation Yaris. This is the case for cruise control, so 2012 Yaris owners can DIY cruise control using the same OEM stalk.

For the 2012 the wiring is the same as that of the 2009-2011 Yaris, where the wiring from the ECM to the steering column is (theoretically) there. Also, the 2012 Yaris has the cruise control "On" and "Set" indicators built into the instrument cluster.

CTScott Hello, if you have wiring diagrams for the 2012 Yaris, you help us and us with them? Please much.

[geoded]

Which is code oem cruise control stalk for Toyota Yaris ?

[geoded]

Code for cruise control stalk toyota yaris is 84632-34011 or 84632-0F010, can you help me ?

[geoded]

anyone can help me?

[geoded]

Hello everyone. I bought the pieces of picture 1, I installed according to picture 2 3.4, but the result was negative, to me does not work. I 1ND-TV engine, 1.4 D4D 66kW respectively. Can someone help me? You need to do something else than I did? Have to change terminals 1 and 2 of the 4-pin connector in the 10 pin?

[CTScott]

Hello everyone. I bought the pieces of picture 1, I installed according to picture 2 3.4, but the result was negative, to me does not work. I 1ND-TV engine, 1.4 D4D 66kW respectively. Can someone help me? You need to do something else than I did? Have to change terminals 1 and 2 of the 4-pin connector in the 10 pin?


You have everything installed in the proper place, but according to the wiring diagrams the 1ND-TV Yaris does not support cruise control.

Check the connector on the other end of the spiral cable, which is located under the cover for the lower part of the steering column. The question is if the two wires are present there that would connect to the cruise control stalk wires under the airbag.

[geoded]

I understand the need to loosen the screw from the one in picture 1 and picture 2, but do not know exactly what wires need to see, you have a picture of what should I see there?

[geoded]

Is it worth trying to move to Terminal 1 and 2 of the 4-pin connector at position 1 and 2 of the 10-pin connector? or is in vain? still will not go anything? The blue wire is the ground wire and do not know where to put it if put in place the terminal 1 of the 4-pin plug.

[CTScott]

Is it worth trying to move to Terminal 1 and 2 of the 4-pin connector at position 1 and 2 of the 10-pin connector? or is in vain? still will not go anything? The blue wire is the ground wire and do not know where to put it if put in place the terminal 1 of the 4-pin plug.

No. Where you have the connector is correct for ones that are cruise control equipped.

[CTScott]

I understand the need to loosen the screw from the one in picture 1 and picture 2, but do not know exactly what wires need to see, you have a picture of what should I see there?

I am looking for the connector on the left in the photo below. You will remove the two screws behind the steering wheel and the one by the tilt lever to remove the lower cover.

http://i372.photobucket.com/albums/oo163/ctscott329/Yaris%20Cruise%20Control/ConnD3.jpg

[geoded]

Connector 1? or two, or three ...... ? I think the connector one you mean but I want to call you. Right?

[geoded]

You do not have the wiring diagram for 1.4 d4d? Although I know that the same engine Auris 1.4 D4D has cruise control, I hope someone will hear us and we may find a solution in the future, I just have to have patience.

[CTScott]

You do not have the wiring diagram for 1.4 d4d? Although I know that the same engine Auris 1.4 D4D has cruise control, I hope someone will hear us and we may find a solution in the future, I just have to have patience.

It is connector 1 that we need to look at. I do have the D4D wiring diagrams, where the "engine control" one does not show cruise control, whereby the wiring diagrams for the 1.33L gas engine does. I don't have the wiring diagrams for the Auris, but I do see in the parts catalog that it uses a different ECM.

[geoded]

Thanks a lot for your help CTScott.

[fredansandy]

CTScott,

I am new to this forum. My daughter in Indiana just purchased a 2012 Yaris Sedan without cruise control. I noticed from the pictures she sent, that the cluster is mounted in the center of the dash vs behing the steering wheel as I am seeing in the pictures in this thread. I am guessing that Toyota did a mid-year refresh of the vehicle in 2012 and that she has the older version.

I have two questions...

1) Can I add OEM cruise to her car using your instructions?
2) If so, which directions do I use. The ones for 2009-2011 or the ones for 2012?

I have added OEM cruise to another daughters 2010 Cobalt. This looks much easier than that.

Thanks,
Fred

[CTScott]

CTScott,

I am new to this forum. My daughter in Indiana just purchased a 2012 Yaris Sedan without cruise control. I noticed from the pictures she sent, that the cluster is mounted in the center of the dash vs behing the steering wheel as I am seeing in the pictures in this thread. I am guessing that Toyota did a mid-year refresh of the vehicle in 2012 and that she has the older version.

I have two questions...

1) Can I add OEM cruise to her car using your instructions?
2) If so, which directions do I use. The ones for 2009-2011 or the ones for 2012?

I have added OEM cruise to another daughters 2010 Cobalt. This looks much easier than that.

Thanks,
Fred


Hi Fred,

Sedans did not get an update in 2012 as liftbacks did, so for your daughter's car the my 2009-2011 directions are the ones you will follow.

[JZA80]

The procedure for removing the steering wheel airbag is a little different for the 2012, where three clips secure the airbag to the steering wheel (rather than 2 screws like the 2006-2011 Yaris).

44503


Also, for the 2012, the lower steering wheel cover has a separate removable cover section for where the cruise stalk goes through, called the "lower no. 2 steering wheel cover"

44504

I'm trying to remove a 2012 Yaris steering wheel airbag. I can see the 3 spring clips but cannot understand how you release them, does it require a special tool? can anyone help explain?

[CTScott]

I'm trying to remove a 2012 Yaris steering wheel airbag. I can see the 3 spring clips but cannot understand how you release them, does it require a special tool? can anyone help explain?

The pin that goes into the spring clips has a groove in it that the spring clip latches onto, so you are trying to open the legs on the clip to release it from the groove.

[takumu0307]

How do you do, it is called takumu. It has ridden on Japanese use of 12 models. There is no cruise control in vitz of Japanese use, and I am troubled by it. It did not operate, even if it post-installed the cruise control switch. If it investigates, there is no wiring of a spiral cable to the point. Who has a wiring diagram of the cruise control of yaris of 12 models? Or please let me know wiring to a computer. Thank you for your consideration.

[CTScott]

How do you do, it is called takumu. It has ridden on Japanese use of 12 models. There is no cruise control in vitz of Japanese use, and I am troubled by it. It did not operate, even if it post-installed the cruise control switch. If it investigates, there is no wiring of a spiral cable to the point. Who has a wiring diagram of the cruise control of yaris of 12 models? Or please let me know wiring to a computer. Thank you for your consideration.

Welcome! It is always nice to hear from people from the birthplace of the Yaris (Vitz). I believe that the third generation Vitz still does not support cruise control. The European third generation Yaris (only the one with the 1.33L engine) now does, but not the Japanese one. The reason I think this is that the parts catalog for the Japanese Vitz does not list any parts related to cruise control.

On the ones that do have it, Pin 60 of ECM connector A72 is where one wire of the stalk connects to and the other wire connects to chassis ground.

[takumu0307]

Mr. CTScott, thank you. My car is 1 KR-FE engine. Somehow, the form of the connector of A70 was different. It was connector-shaped [ of the same engine computer as yaris(es) from 2006 to 2011 ]. The wiring which is already different is stuck in the wiring place of the cruise control of 2011 models. It was troubled.

[spammenot66]

hi CTScott,
Are you still selling anymore of your kits? I've brought a rostra kit from amazon and the instructions are confusing. I've followed everything up to the ECM part of the instruction. I have a 2012 Yaris 5D LE. How do i determine whether my car has "CLUTCH ECM HARNESS" or not? Where the heck is the "ENGINE COMPARTMENT ON THE PASSENGER SIDE FIREWALL"

Any help would be greatly appreciated

[CTScott]

hi CTScott,
Are you still selling anymore of your kits? I've brought a rostra kit from amazon and the instructions are confusing. I've followed everything up to the ECM part of the instruction. I have a 2012 Yaris 5D LE. How do i determine whether my car has "CLUTCH ECM HARNESS" or not? Where the heck is the "ENGINE COMPARTMENT ON THE PASSENGER SIDE FIREWALL"

Any help would be greatly appreciated

Rostra is apparently smoking crack on this one. Installation on a 3rd gen Yaris does not require popping the hood for any reason other than to temporarily disconnect the battery for safety reasons.

My kits are still for sale and for 3rd gens I also stock the little cover for the side of the steering wheel, so no drilling is even required.

[spammenot66]

good to know i've wasted ALOT of time opening everything trying to figure that part out. Everything about their stupid instruction seems wrong.
1)"For 2012 Yaris: Using a "Torx" Driver, push in the 3 snap rings to disengage it from the 3 pins" - After checking out this site, i realized a flat head screw driver should do the trick.
2)The template cut didn't make sense - 1.5 inch hole saw is not needed. It was simpler to just use a razor to cut out a rectangle for the piece. As for the 1/4 pilot hole, i never understood what it was for.
3) If you're right about the "BLACK ECM CONNECTOR C20 IN THE ENGINE COMPARTMENT ON THE PASSENGER SIDE FIREWALL", that's more wrong info from them for page 6 (steps 1-3)

Their instructions are the worst (http://www.rostra.com/manuals/250-1836_Form5370A.pdf). This was suppose to be specifically for the 2012 yaris. I see that you have also mentioned similar instructions within the forum matching theirs on page 7 (steps 5 to 7).

Do i still need to do this? BTW, can you PM me on how to buy from you?

[CTScott]

good to know i've wasted ALOT of time opening everything trying to figure that part out. Everything about their stupid instruction seems wrong.
1)"For 2012 Yaris: Using a "Torx" Driver, push in the 3 snap rings to disengage it from the 3 pins" - After checking out this site, i realized a flat head screw driver should do the trick.
2)The template cut didn't make sense - 1.5 inch hole saw is not needed. It was simpler to just use a razor to cut out a rectangle for the piece. As for the 1/4 pilot hole, i never understood what it was for.
3) If you're right about the "BLACK ECM CONNECTOR C20 IN THE ENGINE COMPARTMENT ON THE PASSENGER SIDE FIREWALL", that's more wrong info from them for page 6 (steps 1-3)

Their instructions are the worst (http://www.rostra.com/manuals/250-1836_Form5370A.pdf). This was suppose to be specifically for the 2012 yaris. I see that you have also mentioned similar instructions within the forum matching theirs on page 7 (steps 5 to 7).

Do i still need to do this? BTW, can you PM me on how to buy from you?


The page 7 info is completely wrong for a 2012. The 2012+ are all prewired. The only thing that would have to be done is to install and plug in (connector is present) the clutch switch for a manual transmission Yaris.

So, for 2012+ just install the stalk and you're done for an auto. For a manual, also install the clutch switch. All wiring is present, so it is just a matter of plugging them in.

[dobrik]

Hi All,

Fitted the Scott's CC kit on Yaris 2013, 1.33 1nr-fe CVT.
Touch 'n Go head unit didn't ask for security code after the battery disconnect, also all settings were not reset (radio, BT, sound settings).
To get out the airbag from the wheel with side gear switches - is real pain, took me like 40 min.

CC works like a charm :), the plastic cover panel didn't fit though, waiting for Scott to figure that out.

Update: Scott emailed me the partnumber of the cover panel and I got it from the local dealer for $10 with taxes (btw Scott had refunded me the wrong part cost at the moment I've reported it)

https://lh5.googleusercontent.com/-pVhy2lRJ7aY/UnOyBshUjkI/AAAAAAAABN4/kYpECsqsLoE/w913-h685-no/IMG_1809.JPG

[er6nphil]

Does anyone know if this will work on my 2013 1.4 d4d ?

Thanks

[CTScott]

Does anyone know if this will work on my 2013 1.4 d4d ?

Thanks

No. Unfortunately only the 1.33L European Yaris supports cruise control.

[er6nphil]

Is there any kit that you know about that does ?

[CTScott]

Is there any kit that you know about that does ?

I have seen a couple of aftermarket kits listed on European websites (I posted a link in one of the threads on here). Those kits sell for $400 to $600 US from what I have seen.

[maxcrack]

No. Unfortunately only the 1.33L European Yaris supports cruise control.

And the 1.0L European Yaris with MMT... It is supported?

[CTScott]

And the 1.0L European Yaris with MMT... It is supported?

I do not believe that the 1.0L supports cruise. Only the 1.33L wiring diagrams indicate that cruise control is available on it.

[SecondYaris]

Just a quick post to thank Scott, just installed the cruise control on my 2013 3 door. This is my second Yaris first was a 2007 that got totaled in 2012 with 245000 miles on it. The install was quick and easy like 20 minutes. The hardest part was being careful releasing the 3 pins that hold the (horn airbag assembly), don't force it just press it with light force you will see the assembly unlock and you will hear it. Works great and the cover was worth the extra $5, makes it look nice and clean, just like OEM at 1/8 the cost.

Mods so far with 2003 miles on it performed in this order, TRD sway bar, Tanabe Medallion axle back, and of course cruise control. Next lightweight belt pulley, then AFE intake.

[modify34]

hi, I have a 2013 model toyota yaris multidrive s car. Is it possible for me to attach it a cruise control

[Drbailey]

Hi.. First post.... I have a 3 door 2012 European SR model Yaris with the four steering wheel buttons.... Looking to fit cruise control... Scott do you supply kits for this car? I was told when we bought the car CC was not an option....

Thanks
Dave B

[CTScott]

Hi.. First post.... I have a 3 door 2012 European SR model Yaris with the four steering wheel buttons.... Looking to fit cruise control... Scott do you supply kits for this car? I was told when we bought the car CC was not an option....

Thanks
Dave B

Welcome. Which engine does your SR have? To be best of my knowledge cruise only works with the 1.33 L.

Shipping to the UK is no problem.

[Stenis]

Hello new here / anybody know if it possible to install Cruise Control to a Yaris 2012 hybrid XP13M(A) from Europé.

[scmoky]

Ask CTScott, but I think that is possible, because in our country the hibrid can have CC in stock new car. You have 1.5l engine?

[CTScott]

Hello new here / anybody know if it possible to install Cruise Control to a Yaris 2012 hybrid XP13M(A) from Europé.

Yes. As mentioned above, cruise is an option of the Yaris Hybrid, so they should all be setup for it.

[Stenis]

Ask CTScott, but I think that is possible, because in our country the hibrid can have CC in stock new car. You have 1.5l engine?

Yes i have 1.5l Engine. I have asked an toyota dealer and they said it cost about 1250 usd to fit CC in my car. :mad:

[CTScott]

Yes i have 1.5l Engine. I have asked an toyota dealer and they said it cost about 1250 usd to fit CC in my car. :mad:

Remove the lower steering column cover and snap a picture of the black connector that plugs into the spiral cable assembly (the black plastic ring behind the steering wheel that allows the connections within the steering wheel to rotate). My bet is that the wires are present for cruise control, so all you will need to do is to add the stalk under the airbag.

[Stenis]

Remove the lower steering column cover and snap a picture of the black connector that plugs into the spiral cable assembly (the black plastic ring behind the steering wheel that allows the connections within the steering wheel to rotate). My bet is that the wires are present for cruise control, so all you will need to do is to add the stalk under the airbag.

Ok i will do so. My understanding is to remove the cover for CC take a picture. Do i need to remove airbag? for the picture? I will try to do so and take a picture soon and hope for a good reply :w00t:

[CTScott]

No. Just remove the two screws that are exposed by turning the steering wheel to either side and the one down by the tilt lever

[scmoky]

And check with you VIN number and model, if under electrical categorie is cruise control(auto drive) option.
webpage http://www.toyodiy.com/parts/

[Stenis]

No. Just remove the two screws that are exposed by turning the steering wheel to either side and the one down by the tilt lever

Hi CTScott
Sorry for the late reply. Took some pictures under the wheel, hope that you can see someting i can't, hopefully you can tell if the wires are present or not?
//Stenis

53384

53385

53386

[CTScott]

The connector of interest is the black one at the top left of this picture. I see by the number of wires that you have steering wheel audio controls. I can't see all of the wires, but the blue one looks like it is in the correct position.

http://www.yarisworld.com/forums/attachment.php?attachmentid=53386&d=1398601351

[Stenis]

The connector of interest is the black one at the top left of this picture. I see by the number of wires that you have steering wheel audio controls. I can't see all of the wires, but the blue one looks like it is in the correct position.

http://www.yarisworld.com/forums/attachment.php?attachmentid=53386&d=1398601351

OK I WILL TRY TO TAKE A BETTER PICTURE // BACK SOON
AND THANKS AGAIN FOR ALL THE HELP

[rc_osu]

Hi!

I just bought a 2012 Yaris and so far it's great, but it too lacks cruise control (among a few other things, but that's the big one). A google search for how to add it brought me to this forum, so I thought I would see if there are still parts available! I'm not very good with cars and the terminology involved so please forgive me if I ask dumb questions. The basic extent of my skills are I can hold it, or I can go get it! So I'm hoping I can learn a little bit about this too.

The Yaris I have isn't like the ones in the pictures though, it has the gauges in the center like fredansandy described.

If you have parts available still for it, could you let me know?
Thanks!

[CTScott]

Hi!

I just bought a 2012 Yaris and so far it's great, but it too lacks cruise control (among a few other things, but that's the big one). A google search for how to add it brought me to this forum, so I thought I would see if there are still parts available! I'm not very good with cars and the terminology involved so please forgive me if I ask dumb questions. The basic extent of my skills are I can hold it, or I can go get it! So I'm hoping I can learn a little bit about this too.

The Yaris I have isn't like the ones in the pictures though, it has the gauges in the center like fredansandy described.

If you have parts available still for it, could you let me know?
Thanks!


Your 2011 Sedan is really a 2011 as far as cruise control goes. The sedan did not get the 2012 revision that the liftback did. I just shot you a PM with the info on the parts.

[Stenis]

Hi again, CTscott

Took some more pictures today. Totaly are there 6 cables to this connection. Cables colour are blue, pink, red, black, brown and light brown.
Can you tell if my car is ready for cruise control.

Thanks again // Stenis

53400

53401

53402

[CTScott]

Hi again, CTscott

Took some more pictures today. Totaly are there 6 cables to this connection. Cables colour are blue, pink, red, black, brown and light brown.
Can you tell if my car is ready for cruise control.

Thanks again // Stenis




The beige and brown wires in pins 1 and 2 are the cruise control wires, so you are good to go for installing cruise control. If you are interested I sell the stalk with wiring harness and mounting screws for far less than dealer price. Even with shipping to Sweden it would be quite a bit less.

[geoded]

In this picture, which is 12V +, after switch ON? Please?

[CTScott]

Nothing visible in that picture is switched +12. Below that picture is the connector for the ignition switch and the pink wire on that connector is switched +12.

[geoded]

Hi CTScott, please tell me which is the color wire coming out of the 12 + immobilizer when the switch is ON

[CTScott]

Hi CTScott, please tell me which is the color wire coming out of the 12 + immobilizer when the switch is ON

You should really have posted your questions in a separate thread, as this is not cruise control related, but the 12 volt immobilizer power wire is the pink wire on the black connector at the end of the black plastic section of the ignition switch assembly.

[Zantiszar]

Hello CTScott after about reading the whole lot of posts I wanted to ask you will this work on a 2014 5 door model L Yaris it's has a 1.5L engine on it and it's an automatic drive model.

I'm curious since my dash looks a lot like yours and for long trips CC would be very useful especially when visiting the family across the island :D your input is much appreciated


Sent my iPush 4s?

[CTScott]

Hello CTScott after about reading the whole lot of posts I wanted to ask you will this work on a 2014 5 door model L Yaris it's has a 1.5L engine on it and it's an automatic drive model.

I'm curious since my dash looks a lot like yours and for long trips CC would be very useful especially when visiting the family across the island :D your input is much appreciated


Sent my iPush 4s?

Yes - Cruise control would work with no problem on your 2014. For your automatic you would only need the stalk with harness and mounting screws.

[geoded]

I am looking for the connector on the left in the photo below. You will remove the two screws behind the steering wheel and the one by the tilt lever to remove the lower cover.

http://i372.photobucket.com/albums/oo163/ctscott329/Yaris%20Cruise%20Control/ConnD3.jpg


This is my car connector, (1ND-TV), has beige and brown is, but cruise control does not work. :-)

[CTScott]

Correct - The 1ND-TV engine computer does not have cruise control capability built into it.

[geoded]

But the harness exist :-)

[CTScott]

But the harness exist :-)

Yes. Toyota was not nice to include the wires but not the function.

[Stenis]

Hi again CTScott
I whant to thank you for helping me with CC install on my car and to let you know that it's working great all the functions are exactly the same as it would have been fitted by toyota dealer. Your kit really saved me some cash. :-) BIG SMILE // Stenis

[TheLaptopGuy]

Hi CTScott

I'd like to buy your CC kit with the plastic cover. Driving a 2013 Yaris 1.3L Auto with radio controls on the wheel.

cheers

[CTScott]

Hi CTScott

I'd like to buy your CC kit with the plastic cover. Driving a 2013 Yaris 1.3L Auto with radio controls on the wheel.

cheers

PM sent.

[Ecoman44]

I've had my 07 3 door yaris for some time now and was looking at getting a 2014 5 door. Of first concern to me was cruise so my first thought was to see if CTScott had a solution posted on this forum yet. As always, I have not been let down. This forum has been the most informative forum I have ever been a part of and it's a huge thanks to you CTScott.

[TheLaptopGuy]

Hey CTScott, the CC kit arrived today.
15 mins and I had working cruise control!. Thanks a lot. Was dead easy to fit up.

[TheLaptopGuy]

Attn Yaris owners!- CTScott's cruise control kit is super easy to install and much much cheaper than the $950 that my Toyota dealer quoted!.

[geoded]

Today I installed an aftermarket cruise control for toyota yaris 1.4 d4d. It is very good and I am delighted investment. I highly recommend.

[CTScott]

That looks like a good solution for Yaris that don't support OEM cruise control. How expensive was it?

[geoded]

Aprox. 400 euro, all taxes, including transportation, because it was bought in the Czech Republic.

[geoded]

Thanks CTScott for your help.

https://www.youtube.com/watch?v=9wzFITUiFkQ

[CTScott]

Excellent!. 400 Euros is quite expensive, but it is the most reasonably priced European solution that I have seen.

[supersonicsixteen]

It looks like this thread is just about dead, but I was wondering if the video for the 2012 Yaris install ever was captured. Any help would be wonderful, thanks!

[hans solo]

where can I buy cruise control for a 2012 yaris five speed?

[CTScott]

where can I buy cruise control for a 2012 yaris five speed?

I sell all of the parts required.

[dobrik]

Hi CTScott,
Do you know if your CC kit would work on Rav 4 2011 CVT (european model)?
Thank you

[CTScott]

Hi CTScott,
Do you know if your CC kit would work on Rav 4 2011 CVT (european model)?
Thank you

I believe it will, but I will do some research to confirm.

[dobrik]

thanks!

[Punishdln]

:biggrin:Now i need a how-to for the ap900 :)

[stykerdk]

Here is the how to for ap900c in Danish but it is simple.
http://www.asmarketing.dk/f/f1/AP900C_Toyota-Yaris-14-Diesel-2009.pdf
You Will also need the wire tharness no 190-5002220
http://www.autobutik.sk/product-21529-190-5002220/

[karloslatynos]

Also ordered from CTScott and got the parts in UK very quickly and no customs issues (despite USPS tracking saying the package is still in USA!)

I notice my steering wheel assembly is slightly different from Richard_RSP's (but thank you for the pictures that helped a lot in knowing what I was aiming for.

I have the steering wheel audio and also the bluetooth telephone control on my UK Spec 2012, 1.33 Yaris TR Auto (not sure which bit of that means I have the different clips though!)

Also, pin 1 & 2 of the 10-pin connector are already occupied so I put the cruise in the spare 4-pin socket next to it.

Edit- It works!

Hello everyone,

CTScott, I've received your kit (thank you).

I've tried to install that today but got stuck when tried to remove the airbag. The steering wheel of my Yaris is exactly the same like one on the pictures above but I couldn't get access to the clips. The steering wheel back cover has only one hole (in the middle). Any idea how do I unclip the remaining two?

thanks

Had a look athe post 55 (thanks Stuart_f) & hopefully I will be able to manage to do this way

[Kirill]

Hello C Scott,

I have the 2009 yaris Sol 100HP MMT transmission I will appreciate your help. could you please check if it possible to install the cruise control on my car?

[w1p30ut]

Big thanks to C Scott.

Fitted mine this week and it works a treat. Reasonable easy to install except for one stubborn spring clip>

Thanks again.

[karloslatynos]

Finally got my cruise control kit installed and tested on my Yaris III. Works perfect and I find it very usefull.

The installation process is very simple exept removing the airbag. It was absolutely nightmare! The access to the side clips is very limited. As somebody said in the post 55 the side clips required to be lifted. I couldn't do that with the clip located near to stalk control. I even removed two screws holding the audio panel on the steering wheel to make more room to access that bloody clip. Finally I've managed to completely pull out the clip from it nest and the airbag popped out. What a relief that was.... I was able to start breathing again. The rest of the installation process (including final push the airbag to the steering wheel) took less than 5 min.

I strongly recommend to all Yaris users to get the cruise control from CTScott. The price is reasonable and as I mentioned before its worth every penny.

[karloslatynos]

I have tested the cruise control on a long trip (Birmingham UK - Brussells BEL) & I am so impressed with it. Apart of driving comfort it also has reduced the fuel comsumption big time.

Someone said to me that using cruise control will increase breake pads usage. How does actually work? Does cruise control use breaks to keep constant speed while driving downhill?

[GustavAlshauge]

Heyy, im new here, i have a yaris 1,8 vvt-i Ts. Do any of you know if i can get the original toyota cruise control to fit in my car??

[GustavAlshauge]

ps, my Ts is from 2007.

[CTScott]

I have tested the cruise control on a long trip (Birmingham UK - Brussells BEL) & I am so impressed with it. Apart of driving comfort it also has reduced the fuel comsumption big time.

Someone said to me that using cruise control will increase breake pads usage. How does actually work? Does cruise control use breaks to keep constant speed while driving downhill?


Cruise control does not have the ability to actively brake the car. It can only do so with engine braking.

[CTScott]

Heyy, im new here, i have a yaris 1,8 vvt-i Ts. Do any of you know if i can get the original toyota cruise control to fit in my car??


Unfortunately there is not an OEM solution for your Yaris.

[haunter1982]

Hi there.

I have installed the switch, the Cruise Control works with no problems, BUT the lights in the dash are not active.
Could it be that there a no bulbs installed? I think this should be LED or not?
Someone have an idea?

One hint for dismounting the Airbag.
The first spring is simple, just press a screwdriver into the hole on the bottom. (as described here in the thread)
The second spring comes of through the side-panel, which you have to remove to see the spring and later install the switch (also as described here in the thread)
The third spring seems complicated but as the holes are elongated you only have to slide the hole Airbag-Unit a little to the otherside and the unit comes off.

[CTScott]

Some of the European instrument clusters are not equipped with the indicator.

[haunter1982]

Damn. I can see the sign but it doesnt light up. Are there bulbs or LED's in the Instruments?

[CTScott]

LEDs

[scmoky]

Haunter
I'm from Slovenia, and have same problem. CC from scot works flawless, but no light indication. I tried to check if there are some leds, but gaguge needle is hard to remove or i don't now a right way to remove to check if there are missing two leds. :evil:
If there are not any leds, maybe if solder up some leds an try?

[CTScott]

I don't think that the LEDs would work if you added them. From what I have found with the software in the clusters, it doesn't drive the features not present.

[haunter1982]

Is there a way to activate it through techstream?

[CTScott]

No

[haunter1982]

Just found out that 45186-52030 C0 is not the right part for my steering wheel. 5$ spent for nothing. dammit.
But now i have the flexible rubber part and can make the origin part fit right.

[CTScott]

Just found out that 45186-52030 C0 is not the right part for my steering wheel. 5$ spent for nothing. dammit.
But now i have the flexible rubber part and can make the origin part fit right.

Yes. The part for the European Yaris is a different shape. I have the correct part number listed somewhere in this thread.

[apmatzen]

Three weeks away I bought a 2014 Yaris (2015 model).

It has the 1.33L 1NR-FE engine.

Does that one have the wiring?

[CTScott]

Three weeks away I bought a 2014 Yaris (2015 model).

It has the 1.33L 1NR-FE engine.

Does that one have the wiring?

Yes it does. All you need is the stalk with harness and the steering wheel side trim piece.

[apmatzen]

Yes it does. All you need is the stalk with harness and the steering wheel side trim piece.

Is it something you have in stock?

[CTScott]

Is it something you have in stock?

I stock the stalk and harness and the trim pieces for the US 3rd generation, but the European 3rd generation Yaris have a slightly different steering wheel back cover, so you'd have to grab that piece from the dealer.

[meszar]

Hi CTScott, I would like to ask whether it is possible to install cruise control Yaris 1.0 2014 purchased in the Czech Republic?

[CTScott]

Hi CTScott, I would like to ask whether it is possible to install cruise control Yaris 1.0 2014 purchased in the Czech Republic?

I don't believe that the ECM for the 1.0L supports cruise control.

[apmatzen]

Hmm...I've had 1.0 2012 and I asked the local dealer If they Can install cc in the car...and they can.

But I never got it installed, because I bought another car.

So it can be done, but its very expensive.


Sent from my iPhone using Tapatalk

[meszar]

I don't believe that the ECM for the 1.0L supports cruise control.

It did not please me very much. but it is interesting that Toyota offers 1.0 liters senso packet, which includes cruise control. I do not feel that because of this changing in the production of the control unit.

[CTScott]

It did not please me very much. but it is interesting that Toyota offers 1.0 liters senso packet, which includes cruise control. I do not feel that because of this changing in the production of the control unit.

I think something might have gotten lost in translation. What do you mean by "senso packet"?

[meszar]

when I bought Yaris, and the opportunity to take it with Senso Packet, but I could not wait a month, unfortunately.
Senso packet includes:
Dual-zone automatic air conditioning
Rearview mirror with automatic iris
Smart Entry & Start
Twilight sensor
Rain sensor
The air-conditioned glove glove box
Cruise control

[CTScott]

Interesting. So, in that case it sounds like the 1.0 can now do cruise. If you want to be sure, you just need to pull the lower steering column cover and check for 12v on the CCS wire (pin 1 of the spiral cable connector).

[meszar]

Which pin do you mean? :)

[CTScott]

On the black connector on the upper left in the first picture, measure the voltage on the grey and brown pins with the ignition in the ON position (engine not running)

[meszar]

Brown - 0
Grey (right of brown) - 5 - 5,5

[panosvo]

In my Toyota Yaris D4D 2013/05 model STYLE TYPE- NLP130L-CHFSXW, everything is in place, even the clutch switch s in place, but unfortunately the pin1,2 voltage is not there. So the ECM does not have the cruise control function in it. Is there a way to add it? Just wonder

Here are the photos!
http://s13.postimg.org/g0f93rofb/IMAG0064.jpg


http://s13.postimg.org/5rmrxy0dj/IMAG0067.jpg

[CTScott]

Brown - 0
Grey (right of brown) - 5 - 5,5

Interesting. I have not had the opportunity to measure the voltage on the CCS wire of a third generation Yaris, so the 5V, rather than 12V might be OK.

Try jumping the brown to the grey with the Ignition ON, but engine off (you can use a bent paper clip or small piece of wire). If you touch those two terminal together briefly you should be able to toggle the cruise control symbol on and off on the cluster, if it works.

[ghidz]

Hi, sorry for my english, i'm italian. I've bought this cruise control

http://pages.ebay.com/link/?nav=item.view&alt=web&id=121696668129&globalID=EBAY-IT

I've checked all the cable and they seems to be ok but the cruise is not working.
If anyone of you can help me will make me very very happy :)

I drive a 2013 Toyota yaris 1.0L

[CTScott]

As far as I am aware, the 1.0L does not have the ECM programming for cruise control.

[ghidz]

Oh hell. What happen if i go to the dealer? can they reprogram the ecm or is not possible?

[CTScott]

Oh hell. What happen if i go to the dealer? can they reprogram the ecm or is not possible?

No. You would need an aftermarket cruise control system, which can be quite costly.

[texascolt45]

anyone try this on a 2015 1.5 liter L model with an auto trans?i'm curious to know if it will activate the cruise.

[CTScott]

anyone try this on a 2015 1.5 liter L model with an auto trans?i'm curious to know if it will activate the cruise.


Yes. I have sold quite a few kits to people with 2015s.

[850spdr]

Hi-
I have a 2013 Yaris which has a no start will crank problem. My ECM connector configuration and pinouts are different from those on the TIS documentation.
Is there some way I can get valid connector drawings and signal lists? My ECM is a 89661-52R40.
thanks

[CTScott]

Hi-

I have a 2013 Yaris which has a no start will crank problem. My ECM connector configuration and pinouts are different from those on the TIS documentation.

Is there some way I can get valid connector drawings and signal lists? My ECM is a 89661-52R40.

thanks


Please post a separate thread instead of hijacking an unrelated one.

[doller]

Hi
which Toyota part number cc stalk do you yaris sorcerers recommend for my 2015 yaris 1,33 vv-t ?
thumbs up from denmark

wow first post:smile:

[nikatsgr]

sorry for my poor english.first time in forum.In my Toyota Yaris D4D 2012/07 model STYLE TYPE- NLP130L-CHFSXW, everything is in place,and the clutch switch s in place in the pin 1-2 ihave 5 volts in grey wire and 0 in brown i have put a used oem cc switch and did not work!!i have read that european yaris not support cruise control.is it definately???any solution???thanks any way!!!!!

[marspike]

sorry for my poor english.first time in forum.In my Toyota Yaris D4D 2012/07 model STYLE TYPE- NLP130L-CHFSXW, everything is in place,and the clutch switch s in place in the pin 1-2 ihave 5 volts in grey wire and 0 in brown i have put a used oem cc switch and did not work!!i have read that european yaris not support cruise control.is it definately???any solution???thanks any way!!!!!

I have same engine, but mine was product in end 2013 (Business). And mine was delivered with factory CCS whose worked. Two thing, once your CCS was not plug on pin 40 to the ECM. Or second possibility your ECM was not progammed for a cruise control switch.
ECM is a metal box located under the hood in difficult access behind secondary fuse box in right passager side.

[nikatsgr]

ok i will search for pin 40 and if is not pluged anything what shall i plug on it???and second
can i reprogramm my ecm (not me offcourse)or something is missing from ecm?

[kevinj93]

Big thanks to CTSCOTT for letting us know this was possible. I have just fitted cruise control to my 2012 Austrailan 1.3L yaris. I only bought the Yaris recently as a second car, and was nearly put off the purchasr because of the lack of cruise control. I found a switch on eBay for AU$17 delivered for whatwas a $650 option in 2012.

For the 2012 model with steering wheel audio controls you don't need to disconnect the battery or airbag, but it's a good idea to remove the horn fuse from the fuse box next to the battery when you go to push the central airbag and horn button back on to the wheel. If you don't the horn will sound when you push the airbag unit back on to the montings. :redface:

[amit87]

OK I finally done mine! I am from the UK, I ordered the cover part from toyota (part# 45186-0d030-C0 (C0 = black) and cost me £5.60 inc VAT.

I ordered a non OEM stalk off ebay for cheap but hopefully will last and looks/works/feels OEM.

So disconnected the battery, removed airbag, put it all in, put all back together.. DONE! How long did it take... 10min? 15min? 20min? 30min?... nope! 1 whole hour!!!!! thats start to finish. 45min of that was battling the airbag clips!

My car is a 2013 (MY63) Yaris SR 1.33 Manual 5door. It already had the secondary clutch switch etc so literally was plug and play. When connected battery, only thing that rest was the clock, the touch&go even resumed my song so dont worry about having to set everything again, just the clock!

The first clip of the airbag was easy, small screw driver and push and it pops out. The other two... well lets just say I couldnt pull the clips down, they are tougher than I thought! How I got it out eventually was by pushing down in the plastic clips of the airbag which some how released both but this is easier said then done! I was violent so dont be scared, nothing will break as long as you know what you're jabbing. To help me get more access I also removed the steering wheel buttons trim by un doing two screws (1 is oposite the other and are obvious). It wouldnt come off as the airbag was still clipped in but I could pull it off enough to get more access. Thats my tip!

[mikeybee]

Almost two years after CTScott sent me the cruise control kit (thanks!) I have finally installed it... and now have CRUISE CONTROL and a SPEED LIMITER!

I wanted not just cruise control, but the speed limiter too (which I have had on my two previous vehicles). A speed limiter is far more useful in the UK - a crowded country with many speed cameras - rather than cruise control itself, which needs wide open highways like the US. :-)

For this, I needed a replacement switch pad on the right hand side of the steering wheel front, with an extra button replacing the blank under the call pick up/drop buttons. Sourcing this turned out to be a pain in the neck, with various Toyota dealerships either not wanting to help me ("why do you want that?") or being too incompetent to find the right part (despite CTScott providing a suggestion of the part number).

In the end I sourced the required item by buying a second hand steering wheel off ebay from a breakers. Here it is:

http://i.imgur.com/sFfcMLJ.jpg

and here is the cabling:

http://i.imgur.com/NTjnO1u.jpg

I think it's just the green wire that is extra?

My Yaris (UK RHD 2012 model TR 1.33 manual) has done 60,000 miles so I was also thinking about replacing the entire steering wheel, as the ebay one was less shiny from use.

So, after reading this thread carefully, I set to... disconnecting the battery negative first.

First challenge - removing the airbag. I turned the steering wheel upside down to make this easier. The bottom clip comes out easily using a flat bladed screwdriver, getting the other two sides out seemed to involve just wiggling the airbag unit down (so towards the top of the steering wheel, given the steering wheel is upside down), and it popped out.

At this point I decided I was less keen on replacing the whole steering wheel (I don't have a steering wheel puller) and decided to replace just the silver button pad unit. This unscrews with the two screws you can see , and then unclips, although I did break one clip on both the old and new units. This doesn't appear to matter though.

To install the wiring for the new button pads requires disconnecting the airbag as the other wiring goes around it - pull up the yellow tab and then pull out the connector on the airbag.

Fit the new silver section, reconnect the airbag, install the cruise stalk and panel cover. Refit the airbag (two slots at the bottom first, then the one at the top. Help it in by having the flatbladed screwdriver push the clip out of the way)

My Yaris already had the clutch switch installed, so nothing to do down there once I figured out it was already there!

Reconnect the battery, go for a drive. :smile:

Cruise control works as you would expect... on, set, up, down, press clutch and it goes off.

Speed limiter works like this:

1. button on the steering wheel pad to turn it on
2. set speed with down on the cruise stalk. The following display appears!

http://i.imgur.com/XXgimZH.jpg

3. you now cannot exceed the speed indicated, the car cuts the throttle. You can adjust the speed limiter by using up and down on the cruise stalk. Changing gear (or engaging the clutch) does not turn off the speed limiter. If you adjust the speed limit down so you are now exceeding the limit set, the display flashes and power is cut until you are under the speed limit set again.

This is awesome. No more speeding fines. :thumbup:

Apparently the speed limiter feature is built into all European Yarises that could have cruise control. Not sure about the US? Check the cabling and try it?!

And thanks again to CTScott for the original kit!

Mikeybee :thumbup:

[boooggy]

Hello
I have a yaris European model, engine 1nr-fe.
CTScott, do u still have the kit for cruise control?
Thx

[-roninn]

Hello everyone.
I have a Toyota Yaris 2015, 5 door, the European version, with control buttons on the steering wheel.
Does anyone know for what are the wires in the connector (D103 black)
pin 10 - red ?
pin 11 - pink ?
pin 12 - blue ?

I suspect that these pins are of a radio control.

Can somebody confirm this?

roninn

[panayiotis]

hello.i have a 2016 1.33-VVTi Active 1NR-FE automatic eur model right hand drive.does anyone know if i only need the stalk?

[CTScott]

hello.i have a 2016 1.33-VVTi Active 1NR-FE automatic eur model right hand drive.does anyone know if i only need the stalk?

Correct - You just need the stalk and the replacement steering wheel side trim piece.

[Toy Yoda Yaris]

Got the stalk from Scott for $50 and the trim piece for $5-he was very fast with shipping and easy to communicate with. I have the base US model with no buttons on the steering wheel, and installation was a breeze. Park with the steering wheel upside down to make it a little easier to get to the pins that release the airbag and steering wheel cover. The photos were really helpful to know what the release pins for the steering wheel look like/where they were so it only took a minute to take it off. I disconnected the battery and let it sit for half an hour just to be safe, but once I got the airbag off I just held/balanced it on the wheel while I installed the stalk, didn't bother doing anything to disconnect it completely. With the airbag off there was just one 4-pin connection and a horn wire to connect, would have been almost impossible to mess up. This saved me so much $$, and probably only took 15 minutes in total.

[marspike]

Hello Everyone,

Since I've installed an used switch cruise control on my second Yaris 2013. Led cruise control cluster blinking (https://youtu.be/055DBpCVR6A ) . Does I need change stalk cruise crontol ? Or does exist something to fix it ?
Thanks for your help.

[CTScott]

Hello Everyone,

Since I've installed an used switch cruise control on my second Yaris 2013. Led cruise control cluster blinking (https://youtu.be/055DBpCVR6A ) . Does I need change stalk cruise crontol ? Or does exist something to fix it ?
Thanks for your help.

Does your Yaris have the 1.33 L engine?

[marspike]

Does your Yaris have the 1.33 L engine?

Hello Mr Scott,

Thanks for your prompt reply.
Hum I believe that's it. It's a manual 99 horses power vvti. I put on a Verso-s (Ractis, NSP120 100VVTI same engine and manual transmission)
switch cruise control find on car's mum to new yaris. Light blinking. Verso-s is little more largest car based on yaris chassis. Some pieces can be able the Yaris 2012 that's dealer have said.
A second try with switch cruise control on my first yaris 2013 D4d and light blinking yet.
Does the problem come from the multiplex whose doesn't support additional plugging?
Or any stalk cruise control can be fix this problem?

[CTScott]

Hello Mr Scott,

Thanks for your prompt reply.
Hum I believe that's it. It's a manual 99 horses power vvti. I put on a Verso-s (Ractis, NSP120 100VVTI same engine and manual transmission)
switch cruise control find on car's mum to new yaris. Light blinking. Verso-s is little more largest car based on yaris chassis. Some pieces can be able the Yaris 2012 that's dealer have said.
A second try with switch cruise control on my first yaris 2013 D4d and light blinking yet.
Does the problem come from the multiplex whose doesn't support additional plugging?
Or any stalk cruise control can be fix this problem?

Only the 1.33L Yaris has built in cruise control. The 1.0L and 1.4L D4D do not.

[panayiotis]

http://uploads.tapatalk-cdn.com/20160517/beec56f4a7b5ca4c312cf8ca6bd0d042.jpg
Everything perfect and for me.special thanks to Gagi


Sent from my iPad using Tapatalk

[Kiran]

hi guys,

my first post ever on a car forum.

purchased my first ever yaris which I'm so pleased with. desperate to have the cruise control on the car so i purchased it from eBay for like £19.

its arrived, i removed the air bag, connected the stalk and the connector into the unused four pin slot on the right of the ten pin connector.

set everything back up, and the cruise light won't come on. I'm so upset. please tell me what it could be!

my engine code is 1KFR.

its a 1litre petrol manual
2012 plate
has the touch and go system with the bluetooth call buttons on the right of the steering wheel aswell.

awaiting your expert advice!

thanks

[CTScott]

hi guys,

my first post ever on a car forum.

purchased my first ever yaris which I'm so pleased with. desperate to have the cruise control on the car so i purchased it from eBay for like £19.

its arrived, i removed the air bag, connected the stalk and the connector into the unused four pin slot on the right of the ten pin connector.

set everything back up, and the cruise light won't come on. I'm so upset. please tell me what it could be!

my engine code is 1KFR.

its a 1litre petrol manual
2012 plate
has the touch and go system with the bluetooth call buttons on the right of the steering wheel aswell.

awaiting your expert advice!

thanks


Only the 1.33L European Yaris have cruise control built into the ECM. Your car does not, so the kit will not work. You would need a complete aftermarket solution to have cruise control on your car.

[panayiotis]

the hybrid yaris has built for cruise control?


Sent from my iPhone using Tapatalk

[CTScott]

the hybrid yaris has built for cruise control?


Sent from my iPhone using Tapatalk



Yes. The hybrid does have cruise control built in.

[nikotroyota]

Hello CTScott, i own a 2012 yaris with 1nr-fe engine and 6-speed manual transmission. My steering wheel has both audio and bluetooth buttons and today i installed the cruise control stalk with no success. i plugged the 4-pin connector in the empty slot next to the 10-pin connector but the light does not come on when i press the on- off button. The only difference i noticed from the previously posted photos is that the airbag has only one orange connector, not two. Everything else looks the same. Any idea?

[CTScott]

Hello CTScott, i own a 2012 yaris with 1nr-fe engine and 6-speed manual transmission. My steering wheel has both audio and bluetooth buttons and today i installed the cruise control stalk with no success. i plugged the 4-pin connector in the empty slot next to the 10-pin connector but the light does not come on when i press the on- off button. The only difference i noticed from the previously posted photos is that the airbag has only one orange connector, not two. Everything else looks the same. Any idea?

Yes. As mentioned many times in this thread - The only European Yaris which have cruise control functionality built in are ones with the 1.33 L engine. Your Yaris does not have that engine and therefore does not have cruise control capability.

[scmoky]

My CC-light to not working, but otherwise CC works flawless :) You must test on the road.

[nikotroyota]

Thank you for your fast replies but my engine IS the 1,33 L variant- 1329 cc to be exact. This is why I am confused. I did not know that this could be the case meaning the cruise control can work at the same time the light remains unlit. Has anyone else experience the same situation?

[neofitos]

hey everyone!

I am from greece, i have a french made yaris 2012, 1.3.

I installed ebay oem cruise control stalk , the clutch switch is already in place.
But it does not work :( .

No light comes on when pressing the on/off , nothing happens if i try to test it while driving.Is there any fuse i should check? i have read the entire thread ,but i did not find anything usefull.
Any help is appreciated!

[CTScott]

hey everyone!

I am from greece, i have a french made yaris 2012, 1.3.

I installed ebay oem cruise control stalk , the clutch switch is already in place.
But it does not work :( .

No light comes on when pressing the on/off , nothing happens if i try to test it while driving.Is there any fuse i should check? i have read the entire thread ,but i did not find anything usefull.
Any help is appreciated!

Interesting that both of the Greek 1.33 are not working. Can either of you give me the part number of your ECM (engine computer)?

[neofitos]

Interesting that both of the Greek 1.33 are not working. Can either of you give me the part number of your ECM (engine computer)?


#update
just came back from my night shift and i had the chance to try it again in open road. Cruise control works fine , i made mistake with on/off and clicking the set button the fist time yesterday.

the cc light does not work though. i guess there is no way of fixing it, right?

[jstert]

hello ctscott, i would like to add cruise control to my u.s. spec, french made, 2014 yaris L, 1.5 engine, auto trans, that is my southwest snowbird car. i tried to pm you and also went to your f.b. page, both didnt go thru. can you advise how to order your kit? i will ask a local japanese specialty mechanic to do it for me. thanks!

[jstert]

a big public thank you to ctscott! your cruise control kit works fine in my 2014 L. highly recommended!


Sent from my iPad using Tapatalk

[ricky56789]

Thanks for the instructions in this thread! Just got cruise working in my 2012 model

[husaynkhan]

Hi where can i get steering button for my yaris 2012 to buy?

[nvfool]

Thanks to Scott, his parts and his advice I got the cruise control in the wife's yaris in less time than it took to find the tools. And it works great! Thanks again Scott!!

[Captain Yaris]

Hi CTScott, I tried PMing you but it didn't appear to have gone through. I wanted to add CC to my US 2016 Yaris L. Do you sell a kit for this? Please PM me with details, thanks!

[Majoto2]

Hey Scott, I have been inspired by your amazing forum and I was wondering if you still were selling kits. I have a 2012, 3 door, hatch, manual and was wanting to add cc to it!

Please message me if you are still selling.

Thanks for all your hard work, CS :headbang:

[Dodge Aries K]

I tried PM'ing him too and haven't heard back. Hopefully things are ok.

[Captain Yaris]

He must be busy because I recieved a PM from him but I PM'd back and haven't heard anything. I think for some reason this forum's software won't show whether or not a msg is sent. Hopefully I hear back soon. I drive 23,000 miles a year and my right leg is killing me!

[Eduardo_mty]

I just bought a "new" 2017 yaris here on Mexico... It came from Thailand... I try to install a cruise control. The Vin start with MR.

I have a stale and wire... https://uploads.tapatalk-cdn.com/20170403/128275b2becf3a20d52c62de24474453.jpg

Enviado desde mi SM-G935F mediante Tapatalk

[Eduardo_mty]

I hope CTScott can help mehttps://uploads.tapatalk-cdn.com/20170403/b8f1bb37cb23998c1dd443e289051fc5.jpghttps://uploads.tapatalk-cdn.com/20170403/c3ed20ce9698f6657a7b572a97387258.jpghttps://uploads.tapatalk-cdn.com/20170403/7cf0a7c0001ea935283fe3971d9ebacc.jpg

Enviado desde mi SM-G935F mediante Tapatalk

[Eduardo_mty]

You can see the specs.. www.toyota.com.mx
My car is sedan core cvt https://uploads.tapatalk-cdn.com/20170403/66f4de40fba89e975af21304481208e1.jpg

Enviado desde mi SM-G935F mediante Tapatalk

[CrankyOldMan]

Hi CTScott, I tried PMing you but it didn't appear to have gone through. I wanted to add CC to my US 2016 Yaris L. Do you sell a kit for this? Please PM me with details, thanks!

I know that he has in the past. Is there a specific part of the install that isn't covered in the thread? I may be able to help with wiring diagrams if they aren't specifically covered.

[CrankyOldMan]

I have a stale and wire... https://uploads.tapatalk-cdn.com/20170403/128275b2becf3a20d52c62de24474453.jpg

It looks like you don't have the connections in the clock spring. The two airbag wires and the small (4-pin?) connector are the only ones I can see at the top. You would have to get a new clock spring with the right connectors to pass the CC wires through to the harness, and maybe have to run all of the other wires (to the ECU, etc).

Here's one with the extra pins, pictures 4 and 5:
https://www.amazon.com/gp/product/B00XP7ER7C/ref=oh_aui_detailpage_o00_s00?ie=UTF8&psc=1

[Captain Yaris]

I know that he has in the past. Is there a specific part of the install that isn't covered in the thread? I may be able to help with wiring diagrams if they aren't specifically covered.

I got a hold of him via PM and he's helping me with the CC. I've been pretty busy, but I have to look for a connector above the clutch pedal to ensure I need a clutch switch. I've been paying attention to the user: Dodge Aries K, and he bought a 2016 L and had the CC put in. One of his posts mentioned that he'd need a clutch switch, so I'm sure I will too. On another note, when my engine bites the big one, I'll definitely be interested in a 2ZR swap. It looks so enticing! :w00t:

[Dodge Aries K]

Yes, I needed the clutch switch. After that was installed it worked perfectly.