Interior Painting job

[TrYaris]

Hey guys,
I've planed to do a paintjob of ALL the plastic in my car ! Even the tissues...
For now i've painted my board and the middle part. But there is one problem at some point on my board the paint didn't stick and there is some bubbles, i used what the local store said i should use for plastics and it seems to have a little problem.... I've used some primer before I dont know why it screwed up that part... Anyway i'll look a little deeper for the next plastic part. For now here is some pictures of my work !

49041
49040
49042
49039

[MyzticZ3r0]

I think you did an excellent paint job! I personally do not like my air vent colors painted; however, to each their own. About your problem, did you sand all the pieces down? Not all paint can be used on plastics due to coating.

[david_827]

beautiful... what brand paint did u use?

[TrYaris]

About your problem, did you sand all the pieces down? Not all paint can be used on plastics due to coating.

I didnt sand all the pieces, my dash have a texture that I like I was afraid that if I sand it, i'd loose it. I'll post some pictures of the problem later today.

beautiful... what brand paint did u use?

I dont remember, I'll come back with the full name when i'll post the other photos

[TrYaris]

So there is what I told you guys, the paint didnt stick very well only on that part ! Remember : Always sand plastic parts before painting !!
49043

[MyzticZ3r0]

I didnt sand all the pieces, my dash have a texture that I like I was afraid that if I sand it, i'd loose it. I'll post some pictures of the problem later today.



I dont remember, I'll come back with the full name when i'll post the other photos

Correct me if I'm wrong, but I believe if you use fine coarse grit sand paper (1500, 1700, or 2000), you can keep the texture as long as you do not rub the same area with all your might. If you're using paint that does not specifically say that it'll bond to plastic, you have to prep it beforehand by sanding - it allows adhesion. After sanding it down, prime it and then use your selected paint.

[MyzticZ3r0]

And just wondering, are those your tweeters above your air vents? =]

[TrYaris]

And just wondering, are those your tweeters above your air vents? =]

Hehe yes they are tweeters :D I have 2 speaker and tweeters KENWOOD, one 10" Kenwood subwoofer and a Ultimate T5000 amp ^^

[enviri]

sanding will mess up the texture of the dash...that's the issue i had. I sprayed some really sticky plastic adheasion promoter for the paint and let it bake in the hot sun in the summer.

[MyzticZ3r0]

Hehe yes they are tweeters :D I have 2 speaker and tweeters KENWOOD, one 10" Kenwood subwoofer and a Ultimate T5000 amp ^^

Did you cut the plastic above the air vent? I'm trying to figure out where to my tweeters but I do not want to make cut out any of the panels (I would if a scrapyard here had any spare yaris parts).

sanding will mess up the texture of the dash...that's the issue i had. I sprayed some really sticky plastic adheasion promoter for the paint and let it bake in the hot sun in the summer.

I stand corrected

[TrYaris]

Did you cut the plastic above the air vent? I'm trying to figure out where to my tweeters but I do not want to make cut out any of the panels (I would if a scrapyard here had any spare yaris parts).

Sorry I didnt see your post, no I didnt cut/make a hole/anything they are just glued.

[Jaimex2009]

You should use paint vinyl. sand the piece with a very fine sandpaper, then wipe with a degreaser piece. finally using adhesion promoter to dry wait about 5 minutes and begin following these steps to paint with vinyl paint color of your choice

sorry for me english.

[auxmike]

Nice stereo, does it have HD radio too?

[TrYaris]

Nice stereo, does it have HD radio too?

I think so, i'm not sure :iono:

[rainbowyaris37]

That looks awesome! I am hoping to do mine soon :) Not diggin' my beige interior :/

[vivalaflam]

DUDE, OMG! Does it hurt your eyes in sunny days? I couldnt stand the light! I'd never use white..... but each to their own...