WTB THESE PARTS!

[ABSPLASTIC]

Hello! Looking to buy some used, but in good condition parts for 07-08 3 door Yaris:

Rear upper strut tower bar (for rear shock tower bolts)
Miracle X-brace
Harness bar
Carbon fiber hood (can trade plus cash or just cash)
Passenger side Weapon*R seat bracket
MI engine cover in raw aluminum
MI lightweight crank pulley
MI intake manifold
Sparco Reclining seat (local to SoCal preferred)

Also interested in coilovers, but local to SoCal preferred.
Pm or post here. Thanks!

[computerlove87]

1. For the pulley, I would recommend an NST underdrive lightweight pulley. (which can be had in several colors including raw aluminum) I don't think there is any reason to go with the micro image one over the NST, plus the NST you can still get new whereas you can't even get the MI one anymore.

2. There is a guy already selling an intake manifold in this thread:
http://www.yarisworld.com/forums/showthread.php?t=53103
If you look carefully at the end of the list it says "MI neochrome intake manifold, $900"

3. If you are going with a raw aluminum theme in your engine bay, this extra piece wouldn't hurt, its basically a tanabe knockoff upper strut bar in raw aluminum... I just installed it and it looks great, very high quality for only being $40 (plus engine bay bling :-D) http://www.ebay.com/itm/230696368603?_trksid=p2057872.m2749.l2649&ssPageName=STRK%3AMEBIDX%3AIT

4. For the driver's seat, I completely recommend getting a stock drivers seat out of a yaris sedan 'S'... that is what I have in my car, and the height adjustability makes absolutely all the difference in the world. It sits much lower than our stock seats at its lowest height and the stock look means you don't have to live with 'stock' looking seats plus an out of place sports drivers seat.

5. There is also a guy currently selling a CF hood already too... http://www.yarisworld.com/forums/showthread.php?t=52820

Hope that helps with some of it...

PS>Also, us Nor Cal Yaris guys may be headed down your way soon, so take a look at our group NCVC (nor cal vitz club) on facebook if you want to meet up with us when we are there :-)

[invader166]

Might I also suggest some NOS?:thumbup:

http://www.ebay.ca/itm/TOYOTA-TERCEL-YARIS-MATRIX-WET-NITROUS-SYSTEM-NOS-KIT-/360161857758?hash=item53db51d0de&vxp=mtr

[ABSPLASTIC]

1. For the pulley, I would recommend an NST underdrive lightweight pulley. (which can be had in several colors including raw aluminum) I don't think there is any reason to go with the micro image one over the NST, plus the NST you can still get new whereas you can't even get the MI one anymore.

2. There is a guy already selling an intake manifold in this thread:
http://www.yarisworld.com/forums/showthread.php?t=53103
If you look carefully at the end of the list it says "MI neochrome intake manifold, $900"

3. If you are going with a raw aluminum theme in your engine bay, this extra piece wouldn't hurt, its basically a tanabe knockoff upper strut bar in raw aluminum... I just installed it and it looks great, very high quality for only being $40 (plus engine bay bling :-D) http://www.ebay.com/itm/230696368603?_trksid=p2057872.m2749.l2649&ssPageName=STRK%3AMEBIDX%3AIT

4. For the driver's seat, I completely recommend getting a stock drivers seat out of a yaris sedan 'S'... that is what I have in my car, and the height adjustability makes absolutely all the difference in the world. It sits much lower than our stock seats at its lowest height and the stock look means you don't have to live with 'stock' looking seats plus an out of place sports drivers seat.

5. There is also a guy currently selling a CF hood already too... http://www.yarisworld.com/forums/showthread.php?t=52820

Hope that helps with some of it...

PS>Also, us Nor Cal Yaris guys may be headed down your way soon, so take a look at our group NCVC (nor cal vitz club) on facebook if you want to meet up with us when we are there :-)

Thanks for the input!

I already have the front strut bar, but I'm looking for the rear strut tower bar (more like bling up my rear portion)

As for the manifold, the neochrome is cool, but it's a pricey part just for cosmetic purposes, I just want the plain ole manifold lol

I need a reclining passenger bucket seat so that it finishes off my interior a bit. I recline my current seat, which is wrapped in Clazzio seat cover to hide it lol.

I'll check out the carbon fiber hood though!!

[ABSPLASTIC]

Might I also suggest some NOS?:thumbup:

http://www.ebay.ca/itm/TOYOTA-TERCEL-YARIS-MATRIX-WET-NITROUS-SYSTEM-NOS-KIT-/360161857758?hash=item53db51d0de&vxp=mtr

No NOS!! lol! I want my car to live longer lol

[ABSPLASTIC]

I messaged Peter, the guy selling the CF hood, and no response ):