The front brake upgrade thread - just the facts
7 Attachment(s)
Okay so along with my engine swap, I also upgraded my front brakes.
[Picture coming] Edit: You will not be able to use anything smaller than a 15" rim if you do this!! Still gotta check to see if the 15" steel rim will clear. I am thinking it should. I first saw this done in Enviri's thread. I figured I would make an official post about this so newcomers can see a quick good options for upgrades, for cheap. Our cars don't need a ton of braking power, but a little more will never hurt. Big brake kits are $$$$ and can be counterproductive for our cars. We really don't want a lot more rotational weight. It can be tough to fit wheels. Cost. Using the Yaris SE front rotors and calipers from a xD/Corolla are perfect upgrade. It takes us from 255mm to 275mm. A bit more surface area to grab, and slightly bigger rotor and caliper also really fills out the wheel nicely. Pics courtesy of Enviri: Attachment 57130 Attachment 57131 Attachment 57132 So here is the parts list: Yaris SE front rotors: 43512-52130 x2 (I used OEM, I don't think I found A/M of these) Corolla/xD Caliper RH: 47730-12A10 (I used cardone 19-B3435) Corolla/xD Caliper LH: 47750-12A10 (I used cardone 19-B3434) Pads: 04465-02220 (xD number, corolla use a different pn I believe, but will work also. I used Magneti Marelli from my work. They are $76.00 and come with all the hardware. Work awesome, too.) Enviri used Hawk pads (HB627 Z.690 - made for Scion xB/xD & 09+ Toyota Corolla / Matrix / Rav4) Brake fluid. So if you shop right you can probably do this for around $500. I waited until I really needed brake to help justify the costs, since I was gonna buy pads and rotors anyways. That is it as far as base needs. Here are parts I recommend to get the most out of this. (Really not a bad idea, for longevity and if you vehicle has lots of miles.) Stainless steel braided lines. I bought mine from Microimage. A good idea if your vehicle has a lot of miles. I live in PA so the winters are rough here to. Replacing the old rubber lines is never a bad idea. Fronts for about $60. Full set for about $120. I did the rears at the same times since I was already making a mess. Attachment 57126 The other thing I would recommend would be some good caliper paint. I used G2 system, from Tirerack. It is a two part epoxy paint, and it is fantastic. Much easier to do now, before everything is installed. About $40 shipped. Worth the looks and protection, IMHO. Attachment 57127 Attachment 57128 Please excuse my messiness. I also coated the rotor hats, and edges. Attachment 57129 So here comes the best part. These bolt right on. Tool list: Rachet and sockets. Sockets: [double checking sizes] Wrench: 8mm for the bleeders Breaker bar will be useful Possibly a 1/2" impact to loosen the caliper bolts Towels Catch container for brake fluids Just take off your old calipers, pads, rotors and put these on. Whether you just replace front calipers, or do braided lines the whole way around, you will need to bleed the brakes. If you just did calipers, then start with the passenger side when you bleed them If you did lines the whole way around start with the passenger rear, then the drivers rear, passenger front, and finally the drivers front. I went around again just for good measure. How to bleed brakes: You will need another person to help with this. You will have the person in the car pump the brake pedal up and hold it while you crack open the bleeder. Once fluid slows down coming out, then you close the bleeder. Repeat this until the fluid comes out without bubbles, before moving onto the next bleeder. My bleeders were 8mm. I recommend a wrench here for ease of quick opening and closing. Weight comparison courtesy of Enviri: Yaris rotor 8lbs Yaris SE rotor 10lbs Yaris caliper 13lbs Corolla caliper 15lbs So for rotating mass there's a 4lbs increase and in overall car weight its 8lbs [more updates and pictures coming] |
Well, now I've got more things to take off of the Corolla when I go 2ZR-swap shopping...
|
Great that you shared this. I am thinking this will be a worthy upgrade with the new speeds I should be hitting. It will be critical with the shorter shutdowns at the Texas/Arkansas/Colorado Mile venues, etc.
Sent from m-o-b-i-l-e |
Very useful info! I shall invest in this once my turbo install is complete.
Sent from my SM-G920T using Tapatalk |
great info yo
Sent from my SM-J700F using Tapatalk |
Great info and a nice upgrade.
From the picture comparison this upgrade for the yaris seems like it's the stock brakes on my JDM 2007 Vitz RS. I could be wrong thou. |
It is possible that it is the same, since it does use the Yaris SE front rotors. I would imagine that the Vitz RS probably uses the same rotors. I would be curious about your brake pad size.
|
2 Attachment(s)
The Vitz RS pad is about 4-5 mm taller than the yaris pads.
|
2 Attachment(s)
Thank you for this!
Here are dimensions of the Hawk pads for the xD Attachment 57153 Here are dimensions for the Yaris hawk pads. Attachment 57154 |
Quick Q: are 15" the smallest diameter rim you can fit with this brake upgrade? Or will 14" still fit?
|
Quote:
|
15" will be the smallest you'll fit over the bigger brakes.
http://i50.photobucket.com/albums/f3...e/IMG_1235.jpg |
just a FYI: tire rack currently (as of oct 5 2016) has a special on hawk performance pads for this BBK for $40 off regular price.
http://www.tirerack.com/brakes/brake...0&autoModClar= |
Don't want to revivie an old thread, but figured I'd rather keep the facts for this on this thread.
What year Yaris SE are the oem rotors from? I'm due for new rotors and pads next summer and figured if I can get everything off of rock auto it'd be worth it and cheaper than what the OP quoted. I found Yaris SE (2012) A/M rotors for just over $20 each but I can't find a proper part# nor a dimension shoing if it is 275mm OD or not |
Hello Yaris enthusiasts, anyone happen to know if the Yaris SE rotors (275mm) come slotted and drilled? I cannot seem to find them using the Yaris SE pn: 43512-52130.
Appreciate the help! |
all yaris SE is 275 front. MUST BE FROM SE model only.
43512-52130 is not drilled or slotted. |
quick question
"Using the Yaris SE front rotors and calipers from a xD/Corolla are perfect upgrade."
What years for the Yaris SE? And what years for the Xd and Carolla? I work at a Junkyard and we can only look up cars by the year and not a part number |
Scion XD/09 Corolla/Matrix Calipers USED: ~100$ off ebay; ~165$ on rock auto (semi-loaded caliper)
(toyo part# 47730‑12A10|47731‑12A10 06/2007-06/2014 SCION XD ZSP110 12/2007-07/2013 TOYOTA COROLLA ZRE142 2012+ Yaris SE rotors (toyota part# 43512-52130): ~105$ ea (msrp) |
All times are GMT -4. The time now is 05:46 AM. |
Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2024, vBulletin Solutions Inc.