Toyota Yaris Forums - Ultimate Yaris Enthusiast Site
 

 


 
Go Back   Toyota Yaris Forums - Ultimate Yaris Enthusiast Site > Technical Forums > Forced Induction Forum
  The Tire Rack

Reply
 
Thread Tools Display Modes
Old 04-26-2018, 11:19 AM   #19
speedworxs
 
Drives: |Mr2
Join Date: Feb 2018
Location: Edmonton, Alberta
Posts: 55
yeah, caustic solution is only for iron and steel . but aluminium i just used degreaser.
the parts so far are fairly clean. still had to brush the head in ports, but a pretty good solution.
also, cool video with coke cans.
speedworxs is offline   Reply With Quote
Old 04-26-2018, 08:52 PM   #20
atomic_hoji
 
Drives: 2018 Yaris SE 5MT
Join Date: Aug 2017
Location: Kincardine, ON, Canada
Posts: 273
Ya, crazy what the extreme pHs will do to a metal!

Glad to hear it's working. Did the electric heater get it up to temp in decent time and sustain a good, hot temp while soaking?

Looking forward to pics!

-- Adam
atomic_hoji is offline   Reply With Quote
Old 04-27-2018, 11:24 AM   #21
speedworxs
 
Drives: |Mr2
Join Date: Feb 2018
Location: Edmonton, Alberta
Posts: 55
i left the block and head in for a long time, like 6 hrs for the head and almost 24 for the block. the heater does ok, it keeps it warm and such, but not instantaneous . and since its almost 50L of solution, it stays warm when you unplug it.
i will add pics later, as my work comp isn't uploading them...
got it. and after drying, wiped down the bores with wd40
(as much as my gigantic hands would fit in this tiny bore)
Attached Images
File Type: jpg before (1024x576).jpg (378.0 KB, 155 views)
File Type: jpg after1 (1024x576).jpg (372.0 KB, 154 views)
File Type: jpg after2 (1024x576).jpg (338.8 KB, 154 views)

Last edited by speedworxs; 04-27-2018 at 11:57 AM.
speedworxs is offline   Reply With Quote
Old 04-27-2018, 03:11 PM   #22
CrankyOldMan
2ZR swap. DO IT! Ask how!
 
CrankyOldMan's Avatar
 
Drives: 09 Meteoric Metallic HB
Join Date: Feb 2011
Location: West Michigan
Posts: 2,333
Quote:
Originally Posted by speedworxs View Post
yeah, caustic solution is only for iron and steel . but aluminium i just used degreaser.
I've been struggling with which degreaser to use on my aluminium castings as well. Things like Simple Green are caustic, but low concentrations and immediate rinsing will limit the damage.

I'm making an aqueous (water-based) hot wash from an old laundry sink and an immersion bucket heater. That's for steel and cast iron stuff. The aluminium will almost all go into an industrial style parts washer with naphtha-based solvent.
CrankyOldMan is offline   Reply With Quote
Old 04-27-2018, 05:07 PM   #23
speedworxs
 
Drives: |Mr2
Join Date: Feb 2018
Location: Edmonton, Alberta
Posts: 55
yeah, i didn't use degreaser, it was just cleaner but i think the warm temp and sitting for several hours helps.
didn't seem to affect the machined surfaces.
speedworxs is offline   Reply With Quote
Old 04-27-2018, 09:50 PM   #24
speedworxs
 
Drives: |Mr2
Join Date: Feb 2018
Location: Edmonton, Alberta
Posts: 55
mixed news...
my rods showed up, from cxracing on ebay. (draw your own conclusions)
rod is slightly different than the ebay pic, but they are all within 1 gram of each other, and clearly much better than a stock rod.
BUT
didn't include rod bolts, so i have to source them.
and the wrist pin end, is looking too small to machine any larger to accept vitara pistons - then i may just get the forged ones for a 1nz, but will talk to machinist first.
Attached Images
File Type: jpg IMG_20180427_193601.jpg (260.6 KB, 154 views)
File Type: jpg IMG_20180427_193617.jpg (239.7 KB, 153 views)
File Type: jpg IMG_20180427_193631.jpg (254.5 KB, 154 views)
speedworxs is offline   Reply With Quote
Old 04-29-2018, 06:47 PM   #25
atomic_hoji
 
Drives: 2018 Yaris SE 5MT
Join Date: Aug 2017
Location: Kincardine, ON, Canada
Posts: 273
Thanks for the feedback - have to keep that little electric heater setup in mind. Looks like the all purpose cleaner did a decent job.. nice clean block to start a build with

Is it weird to say 'nice rods' ... just sayin'. lol

Good luck with it. Looking forward to progress on this little monster..

-- Adam
atomic_hoji is offline   Reply With Quote
Old 05-04-2018, 11:53 AM   #26
speedworxs
 
Drives: |Mr2
Join Date: Feb 2018
Location: Edmonton, Alberta
Posts: 55
bummer - had to go different piston route than i previously planned.
found a chinese supplier, i can get forged ones for almost the same price as vitara pistons.
if they turn out to be decent quality, i'll share the info- if it turns out to be garbage, then i learned a lesson
speedworxs is offline   Reply With Quote
Old 05-07-2018, 12:13 AM   #27
SirDigby
 
Drives: 2007 yaris 3 door
Join Date: Sep 2015
Location: Denver, Colorado
Posts: 999
...i don't think you're getting that 400hp


but i'm rooting for you
SirDigby is offline   Reply With Quote
Old 05-07-2018, 11:18 AM   #28
speedworxs
 
Drives: |Mr2
Join Date: Feb 2018
Location: Edmonton, Alberta
Posts: 55
thats ok, i still want to say, 300+ is achievable
speedworxs is offline   Reply With Quote
Old 05-15-2018, 11:52 PM   #29
speedworxs
 
Drives: |Mr2
Join Date: Feb 2018
Location: Edmonton, Alberta
Posts: 55
bought my forged pistons today, i'll post the company if they don't turn out s**tty.
50$ for 4 pistons (plus shipping to north america)
speedworxs is offline   Reply With Quote
Old 05-19-2018, 12:50 PM   #30
DarkShadowFox
Banned
 
Drives: 2015 Yaris LE 3door 1F7
Join Date: Feb 2017
Location: Massachusetts
Posts: 963
idk this is the [S]garbage[/S] guide from wiki motors:

"A TRD turbokit for 1NZ is up for grabs. It will allow significantly increasing the stock engine’s capacity. You can assemble such a kit on your own. You should only get an IHI RHF4 turbocharger or something like that. It is also needed to get a turbo manifold, pipes, intercooler, blow-off, thick cylinder head gasket, 2ZZ-GE injectors, 1JZ-GTE fuel pump, and ECU 1NZ-FET/GReddy e-Manage Ultimate. At 9 psi (0.6 bar) boost pressure your motor shows about 150-160 horsepower.
If it’s needed to intensify capacity, you must get forged pistons, connecting rods and lots of other aftermarket parts. In any case, a 1.5-liter engine is not at all designed for setting records.
Besides, one can perform NA tuning, get performance camshafts (JUN), springs, valves, cold air intake, do port and polish, replace the intake manifold, throttle body, purchase a 4-2-1 header, and adjust the ECU. These upgrades help us intensify maximal engine rpm and reach higher rate of capacity. "
DarkShadowFox is offline   Reply With Quote
Old 05-23-2018, 10:46 AM   #31
atomic_hoji
 
Drives: 2018 Yaris SE 5MT
Join Date: Aug 2017
Location: Kincardine, ON, Canada
Posts: 273
The 1NZ is a stout little bugger so I imagine if you put the resources to building it up you can make your target - besides, there are videos of 500+ hp 1NZs out there, so we know it can be done.

Keep us posted as you collect your parts!

-- Adam
atomic_hoji is offline   Reply With Quote
Old 05-23-2018, 02:23 PM   #32
speedworxs
 
Drives: |Mr2
Join Date: Feb 2018
Location: Edmonton, Alberta
Posts: 55
apparently shipping is mucho quick in china, the delivery is here already! but i'm at work so can't pick up until tomorrow, pics to follow
speedworxs is offline   Reply With Quote
Old 05-23-2018, 05:02 PM   #33
WeeYari
 
WeeYari's Avatar
 
Drives: 06 Polar White 5dr, 13 Soul 4u
Join Date: Oct 2008
Location: Georgetown, Ontario, Canada
Posts: 5,739
Quote:
Originally Posted by speedworxs View Post
apparently shipping is mucho quick in china, the delivery is here already!
Consider yourself lucky. Very lucky. Must have been a container full up and ready to go, rather than wait for a shipment to be large enough to leave port.



Sent from my Elite_5_5_Octa using Tapatalk
__________________
WeeYari is offline   Reply With Quote
Old 05-23-2018, 07:32 PM   #34
DarkShadowFox
Banned
 
Drives: 2015 Yaris LE 3door 1F7
Join Date: Feb 2017
Location: Massachusetts
Posts: 963
can we have the ebay link to the china turbo.
DarkShadowFox is offline   Reply With Quote
Old 05-24-2018, 12:52 AM   #35
speedworxs
 
Drives: |Mr2
Join Date: Feb 2018
Location: Edmonton, Alberta
Posts: 55
i haven't bought a turbo yet. but i was going to go a gt2860
heres one, but i wanted to go ball bearing. the larger turbo, the bb will help offset some lag i hope.
https://www.ebay.com/itm/GT28-GT25-G...sAAOSwi8xaJPtm
the rods from cxracing (ebay) and the pistons from alibaba. weirdly you can find all kinds of s**t on that site. i even found a forged billet crank for the 1nz
some things are likely already made in china anyway, so whatever....
but i'll trust my rings from a name brand, and same with the main and rod bearings

if someone wants a turbo too... apparently 2 is minimum order,
https://www.alibaba.com/product-deta...4b1f778b9xZadP

Last edited by speedworxs; 05-24-2018 at 01:03 AM.
speedworxs is offline   Reply With Quote
Old 05-24-2018, 12:56 AM   #36
speedworxs
 
Drives: |Mr2
Join Date: Feb 2018
Location: Edmonton, Alberta
Posts: 55
Quote:
Originally Posted by WeeYari View Post
Consider yourself lucky. Very lucky. Must have been a container full up and ready to go, rather than wait for a shipment to be large enough to leave port.



Sent from my Elite_5_5_Octa using Tapatalk
came in DHL shipment. but i know what you mean.
pistons 50usd, shipping 48, +taxes 20. hopefully i didn't misinterpret the emails and it is a whole set not just one piston. then i will feel pretty dumb
speedworxs is offline   Reply With Quote
Reply

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump

Similar Threads
Thread Thread Starter Forum Replies Last Post
Zage Turbo Kit Install - Toyota Yaris Focus_Sh1ft Forced Induction Forum 160 02-06-2022 08:14 PM
Quantum Technology Hydrogen 1NZ Turbo Kit GT1241 JustDidIt Items for Sale by private party 13 08-31-2018 03:07 PM
Turbo Echo - The False Prophet EchoLaQua Forced Induction Forum 12 03-14-2018 12:58 PM
1nz turbo (england) 1nz_tommy Forced Induction Forum 1 10-17-2014 08:06 PM
Hyundai Turbo Veloster 150kw *MAD DOG* Off-topic / Other Cars / Everything else Discussions 6 01-09-2012 11:35 PM


All times are GMT -4. The time now is 08:06 AM.




YarisWorld
Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2024, vBulletin Solutions Inc.