break line: 1,5 RS vs. 1,8 TS - Toyota Yaris Forums

Patitwelve · 10-05-2010, 04:30 PM

Hey!

I drive a 2008 Toyota Yaris TS with 1.8 liter engine (2ZR-FE). The engine have stock 133 HP.
Next month i’ll install a supercharger, 2,5 inch exhaust and air incooler from Bemani (Switzerland).
The performance after this conversion will be at 215 HP.

I would like to modificate the breaks too, because of this high performance. So there are 2 options:

1) A complete beak system from D2 Racing (6 break pistons, stainless steel break lines, drilled + slotted rotor -> about 800 Euro

2) Swap the break pad with better pads, and install stainless steel break lines

For version nr. 2 i could buy some break lines in the USA:
http://shop.microimageonline.com/Sta...-AP-ssbl-1.htm

Does everyone know if these lines apply to my car? Are the different break systems in Germany (a German 1.8 TS is built in Japan) and the American Yaris?

Thank you so much!

Patrick

ilikerice · 10-14-2010, 08:39 AM

personally. id just upgrade to some good grip tires and throw on some hawk or other performance brake pads and the stainless steel lines also. i think the 6 piston calipers and slotted/drilled rotors are overkill and more for looks than performance..

Patitwelve · 10-14-2010, 04:34 PM

okay thank you!!! i'll do it on the same way, after installing the supercharger.

10-05-2010, 04:30 PM	#1
Patitwelve View User's Garage Drives: Toyota Yaris 1,8 TS Compressor Join Date: Oct 2010 Location: Germany Posts: 16	break line: 1,5 RS vs. 1,8 TS Hey! I drive a 2008 Toyota Yaris TS with 1.8 liter engine (2ZR-FE). The engine have stock 133 HP. Next month i’ll install a supercharger, 2,5 inch exhaust and air incooler from Bemani (Switzerland). The performance after this conversion will be at 215 HP. I would like to modificate the breaks too, because of this high performance. So there are 2 options: 1) A complete beak system from D2 Racing (6 break pistons, stainless steel break lines, drilled + slotted rotor -> about 800 Euro 2) Swap the break pad with better pads, and install stainless steel break lines For version nr. 2 i could buy some break lines in the USA: http://shop.microimageonline.com/Sta...-AP-ssbl-1.htm Does everyone know if these lines apply to my car? Are the different break systems in Germany (a German 1.8 TS is built in Japan) and the American Yaris? Thank you so much! Patrick

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
Zage Turbo Kit Install - Toyota Yaris	Focus_Sh1ft	Forced Induction Forum	160	02-06-2022 08:14 PM
DIY A/C low pressure line insulation	syntax	Middle East	291	06-17-2021 02:05 AM
My Hand Break goes on and off ???	derickveliz2	General Yaris / Vitz Discussion	3	01-20-2010 01:18 PM
Will XA XB's brake line fit our Yaris??	AlainMikli	Wheels, Tires and Suspension Forum sponsored by The Tire Rack	1	06-04-2009 01:22 AM
Installing a external in line transmission filter.	YarisSedan	Performance Modifications	1	03-31-2009 08:03 PM

10-14-2010, 08:39 AM	#2
ilikerice Drives: 2010 black yaris Join Date: Oct 2010 Location: savannah, ga Posts: 2,868	personally. id just upgrade to some good grip tires and throw on some hawk or other performance brake pads and the stainless steel lines also. i think the 6 piston calipers and slotted/drilled rotors are overkill and more for looks than performance..

10-14-2010, 04:34 PM	#3
Patitwelve View User's Garage Drives: Toyota Yaris 1,8 TS Compressor Join Date: Oct 2010 Location: Germany Posts: 16	okay thank you!!! i'll do it on the same way, after installing the supercharger.