Toyota Yaris Forums - Ultimate Yaris Enthusiast Site
 

 


 
Go Back   Toyota Yaris Forums - Ultimate Yaris Enthusiast Site > Technical Forums > DIY / Maintenance / Service
  The Tire Rack

Reply
 
Thread Tools Display Modes
Old 06-15-2011, 12:20 AM   #1
CTScott
ULTIMATE
 
CTScott's Avatar
 
Drives: 09 5dr LB, 2x 08 3dr LB
Join Date: Oct 2008
Location: USA, CT
Posts: 13,460
JDM Automatic A/C Conversion Demonstration

JDM AC Controls.jpg

I have been fiddling with the JDM Automatic A/C system for quite some time now, with the intention of developing a plug and play harness for Steve (echo_hrs), who imported a couple of sets of the required hardware.

To build the PnP harness, I used the female E8 and E9 connectors from a USDM AC ECU, and a male E11 connector from a JDM wiring harness. I also used an ED1 connector and an E4 connector for the fan wiring from a USDM wiring harness. One piece that I missed, when giving Steve the list of JDM parts needed, was the fan speed control assembly from the JDM Auto AC. The USDM AC uses a blower resistor assembly to adjust the fan speed, whereas the JDM Auto AC uses a solid state speed controller, which responds to a pulsed signal from the AC ECU. Since we didn't import that piece, I had to analyze the signal from the JDM AC ECU and create my own solid state speed control to emulate the JDM one.

Here is a video of it in action:

http://www.youtube.com/watch?v=qbInNKKEwFc


Here is the harness that I created:

__________________

Last edited by CTScott; 06-15-2011 at 11:14 AM.
CTScott is offline   Reply With Quote
Old 06-15-2011, 09:45 AM   #2
Liu997
 
Drives: 2008 Red Yaris LB
Join Date: Nov 2008
Location: Hicksville, LI
Posts: 125
How would I do something like this. This is mad hot, If you ever sell a kit let me know
Liu997 is offline   Reply With Quote
Old 06-15-2011, 09:46 AM   #3
Liu997
 
Drives: 2008 Red Yaris LB
Join Date: Nov 2008
Location: Hicksville, LI
Posts: 125
Ohh, just watched the video. Seems too tough ughhh
Liu997 is offline   Reply With Quote
Old 06-15-2011, 11:15 AM   #4
CTScott
ULTIMATE
 
CTScott's Avatar
 
Drives: 09 5dr LB, 2x 08 3dr LB
Join Date: Oct 2008
Location: USA, CT
Posts: 13,460
Quote:
Originally Posted by Liu997 View Post
Ohh, just watched the video. Seems too tough ughhh
It's actually not all that bad. If you look at the photo of the harness, I just added to the 1st post, it really is plug and play. The hardest part is obtaining the JDM (or European) parts.
__________________
CTScott is offline   Reply With Quote
Old 06-15-2011, 11:22 AM   #5
poorsh2
 
Drives: 2008 yaris hb
Join Date: Mar 2011
Location: ne ct
Posts: 68
Can you build it into the tach replacement? LOL
poorsh2 is offline   Reply With Quote
Old 06-15-2011, 01:26 PM   #6
markitect
 
Drives: Yaris
Join Date: Oct 2008
Location: Michigan
Posts: 199
Nice work, what does the JDM parts list look like?
markitect is offline   Reply With Quote
Old 06-15-2011, 02:16 PM   #7
CTScott
ULTIMATE
 
CTScott's Avatar
 
Drives: 09 5dr LB, 2x 08 3dr LB
Join Date: Oct 2008
Location: USA, CT
Posts: 13,460
Quote:
Originally Posted by markitect View Post
Nice work, what does the JDM parts list look like?
There are a couple of threads on here where I list all of the individual parts, but to actually order all of them the cost is well over $2000. So, the better route is to purchase the following used parts via Yahoo Japan auctions:

1. Main AC box with solenoids

2. AC Amplifier (ECU) - Part number 88650-52381, 88650-52610, or 88650-52590. Ideally with the large connector attached.

3. Auto AC Controls (replaces the USDM AC control panel)

4. JDM blower or at least the speed control module off of the bottom of it. (This one is not critical, since I developed an under $50 solution for it).


To make the plug and play harness:

1. Large connector (E11) for the JDM AC ECU

2. USDM AC ECU to harvest the connectors from.

3. USDM Dash AC harness to harvest the blower and ED1 dash connectors from.
__________________
CTScott is offline   Reply With Quote
Old 04-02-2022, 05:44 PM   #8
Aqibfarid
I've made a post!
 
Drives: Toyota Vitz
Join Date: Apr 2022
Location: Pakistan
Posts: 1
Wiring

Hey, great job done, i have purchased everything and installed in my car, now just wiring job is to be done, can you please help me out in making this wiring harness as u have made, i will be really grateful, thanks
Aqibfarid is offline   Reply With Quote
Reply

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump

Similar Threads
Thread Thread Starter Forum Replies Last Post
A/C Not Blowing Cold Air...among other things yarisitis DIY / Maintenance / Service 38 07-28-2016 04:00 PM
DIY: Unlink A/C from Defroster stran DIY / Maintenance / Service 46 01-19-2015 09:17 PM
JDM leather wheel OR JDM Vitz RS rear bumper??? evo165 Cosmetic Modifications (Exterior/Interior) 31 02-14-2012 08:26 PM
FS: JDM Modellist II Front bumper & JDM LED tails DKN-YARIS Items for Sale by private party 7 11-09-2008 01:10 AM


All times are GMT -4. The time now is 02:17 AM.




YarisWorld
Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2024, vBulletin Solutions Inc.