NEED HELP - Toyota Yaris Forums

JumpmanYaris · 07-29-2009, 11:37 PM

I tried to change the turning signal lights puting 2057LED insted of 992(7440A) wich are the one for it Well now my turning signals are not working at all or the hazard ones ANYONE KNOWS WHY?Could it be a Fuse? But where is the Fuse box and what fuse is it?

Shroomster · 07-29-2009, 11:41 PM

when you say you tried to replace it, do you mean you put the old ones back in after the new ones didn't work?

LEGATO`` · 07-29-2009, 11:46 PM

Quote:

Originally Posted by Shroomster

when you say you tried to replace it, do you mean you put the old ones back in after the new ones didn't work?

try what he said
put the old ones back, and if that doesnt work, then it might be the fuse

JumpmanYaris · 07-29-2009, 11:54 PM

I did try that to but i was replacing the left side and the right side isnt working

Shroomster · 07-30-2009, 12:28 AM

there is no light from any corner of the car when you flip the hazards?

highly unlikely that you popped a fuse as the bulb itself acts like a fuse to begin with, but if you reinstalled the original bulbs then yeah check the fuses.

JumpmanYaris · 07-30-2009, 11:07 AM

Yup I tried switching the bulb to the original and the led one as well and no results I need to find where is the fuse so I can check them if not... as much as I dont want to im gonna have to take it to Toyota

CTScott · 07-30-2009, 12:36 PM

It's the 10A one labeled "TAIL" in the fuse panel that is up under the dash (i.e. the one you put your head on the brake pedal to see).

CTScott · 07-30-2009, 12:41 PM

A 2057 is a bayonet mount and a 7440A is a wedge mount.

Out of curiosity, how did you install it?

JumpmanYaris · 07-30-2009, 05:10 PM

Quote:

Originally Posted by CTScott

A 2057 is a bayonet mount and a 7440A is a wedge mount.

Out of curiosity, how did you install it?

Well its the tail lights from Garm so the bulbchanges its not the same plug that the original taillights comes with

CTScott · 07-30-2009, 05:35 PM

Quote:

Originally Posted by JumpmanYaris

Well its the tail lights from Garm so the bulbchanges its not the same plug that the original taillights comes with

OK. So you had the rewire to connect up the new lights, and at the same time you were changing the new ones to LEDs?

Did you find that the fuse was popped?

JumpmanYaris · 07-30-2009, 10:35 PM

I havent checked to much work I will try and see wich one and where it is I will post some pictures of the plug for the bulb so you can see.
Yes its all rewired but they been working for almost a year and now that I wanted them LED amber lights this crap happens

I PRAY TO GOD IT'S JUST A MESSED UP FUSE!!

CTScott · 07-30-2009, 10:37 PM

Quote:

Originally Posted by JumpmanYaris

I havent checked to much work I will try and see wich one and where it is I will post some pictures of the plug for the bulb so you can see.
I PRAY TO GOD IT'S JUST A MESSED UP FUSE!!

The lighting circuits are well protected, so I would almost guarantee that it's the fuse.

SaerinRhoe · 07-30-2009, 01:01 PM

With duct tape and bailing wire.

Just trying to add some humor.

S.R.

CTScott · 07-31-2009, 03:32 PM

The 10A one at the bottom left of your picture is the tail light fuse if you are working on a liftback.

By the way, I'm not digging that white wire stuffed in the meter fuse. I don't think it's part of your current problem, but it's not a good way of doing things...

JumpmanYaris · 07-31-2009, 03:39 PM

Quote:

Originally Posted by CTScott

The 10A one at the bottom left of your picture is the tail light fuse if you are working on a liftback.

By the way, I'm not digging that white wire stuffed in the meter fuse. I don't think it's part of your current problem, but it's not a good way of doing things...

Its the sedan but ill go check reall fast as far as that wire i got jack clue what it is it could be from when they installed the Remote Control or the Sound system i could be wrong thats the only 2 things that i have in my car

JumpmanYaris · 07-31-2009, 03:47 PM

If is that one its intact

CTScott · 07-31-2009, 03:51 PM

There's no fuse in the other place that it would be for a certain config of sedan, so that must be it. Did you pull it and check it closely (ideally with an ohm meter)?

JumpmanYaris · 07-31-2009, 03:53 PM

No, But when a fuse goes out it brakes and that fuse its still new

07-30-2009, 01:01 PM	#13
SaerinRhoe '09 Yaris View User's Garage Drives: '09 Yaris Join Date: Mar 2009 Location: Dallas, Texas Posts: 346	With duct tape and bailing wire. Just trying to add some humor. S.R. __________________ 2009 Yaris 3-Door Liftback MT Black Sand Pearl

07-29-2009, 11:41 PM	#2
Shroomster '07 to '12:2 wipers to 1? View User's Garage Drives: '12 5-door LE & '14 5-door LE Join Date: Apr 2007 Location: Orlando Posts: 1,999	when you say you tried to replace it, do you mean you put the old ones back in after the new ones didn't work?

07-30-2009, 12:28 AM	#5
Shroomster '07 to '12:2 wipers to 1? View User's Garage Drives: '12 5-door LE & '14 5-door LE Join Date: Apr 2007 Location: Orlando Posts: 1,999	there is no light from any corner of the car when you flip the hazards? highly unlikely that you popped a fuse as the bulb itself acts like a fuse to begin with, but if you reinstalled the original bulbs then yeah check the fuses.

07-30-2009, 12:36 PM	#7
CTScott ULTIMATE View User's Garage Drives: 09 5dr LB, 2x 08 3dr LB Join Date: Oct 2008 Location: USA, CT Posts: 13,460	It's the 10A one labeled "TAIL" in the fuse panel that is up under the dash (i.e. the one you put your head on the brake pedal to see).

07-30-2009, 12:41 PM	#8
CTScott ULTIMATE View User's Garage Drives: 09 5dr LB, 2x 08 3dr LB Join Date: Oct 2008 Location: USA, CT Posts: 13,460	A 2057 is a bayonet mount and a 7440A is a wedge mount. Out of curiosity, how did you install it?

07-31-2009, 03:32 PM	#14
CTScott ULTIMATE View User's Garage Drives: 09 5dr LB, 2x 08 3dr LB Join Date: Oct 2008 Location: USA, CT Posts: 13,460	The 10A one at the bottom left of your picture is the tail light fuse if you are working on a liftback. By the way, I'm not digging that white wire stuffed in the meter fuse. I don't think it's part of your current problem, but it's not a good way of doing things...

07-31-2009, 03:51 PM	#17
CTScott ULTIMATE View User's Garage Drives: 09 5dr LB, 2x 08 3dr LB Join Date: Oct 2008 Location: USA, CT Posts: 13,460	There's no fuse in the other place that it would be for a certain config of sedan, so that must be it. Did you pull it and check it closely (ideally with an ohm meter)?