|
10-04-2009, 07:30 PM | #1 |
cruise control not working
Finished wiring the factory cc stalk and clutch switch. cruise not working. What should i look for? What order would you start trouble shooting?
|
|
10-04-2009, 08:22 PM | #2 |
ULTIMATE
Drives: 09 5dr LB, 2x 08 3dr LB Join Date: Oct 2008
Location: USA, CT
Posts: 13,460
|
Triple check that your are really on pin 40 on the ECM to start with. post a pic of your ECM connection if you want an extra set of eyes on it.
|
10-04-2009, 09:51 PM | #3 |
I will double check monday. I used the repair wire from toyota and counted the pins. No cel so i don't think i put it in the mirror image pin. I i will look tommorow.
|
|
10-05-2009, 01:27 PM | #4 |
wire hookups
here are the wiring hookups
|
|
10-05-2009, 01:43 PM | #5 |
ULTIMATE
Drives: 09 5dr LB, 2x 08 3dr LB Join Date: Oct 2008
Location: USA, CT
Posts: 13,460
|
ECM Pin 40 and clutch switch connections look good. On the clock spring connector, I can't tell what you have connected. In the orientation of that picture the bottom right wire should be the ECM pin 40 one and the one above it should be connected to ground.
|
10-05-2009, 02:34 PM | #6 |
ground should be below the horn, ecm to the left of ground? do we know were to get the pins for this conector ? I think the clockspring conector is not making good contact.
|
|
10-05-2009, 02:50 PM | #7 | |
ULTIMATE
Drives: 09 5dr LB, 2x 08 3dr LB Join Date: Oct 2008
Location: USA, CT
Posts: 13,460
|
Quote:
The part number for the pin with a piece of wire attached is: 82998-12870 Cruise - Ground.jpg |
|
10-05-2009, 05:54 PM | #8 |
I ordered the pins and i will install them, I will also use a clutch wire jumper to make sure the switch is ok. Hope that fixes it.
|
|
10-05-2009, 08:11 PM | #9 |
Drives: Toyota Yaris Join Date: Apr 2007
Location: NY
Posts: 13
|
My only problem with the cruise was the clutch switch, jammin connectors in the terminals on the fusebox connections never worked. Went through every connection in the entire car tracking down a loose crimp or a short didnt find anything. So I used quick splice connectors and actually tied into the wires for the clutch-switch, works great now.
|
10-06-2009, 12:06 PM | #10 |
Thanks I will look there today
|
|
10-06-2009, 02:20 PM | #11 |
Flutie, you were right. I reatached the clutch switch wires and the cruise works. Thanks to all those who came before with this diy.
|
|
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
DIY - 2009 Cruise Control for $10, without pulling the steering wheel and airbag | CTScott | DIY / Maintenance / Service | 307 | 04-04-2023 03:43 AM |
Cruise Control - Again! | CB900F2 | DIY / Maintenance / Service | 47 | 06-17-2010 06:29 PM |
Cruise Control | chessclubloser | DIY / Maintenance / Service | 11 | 03-27-2010 11:59 AM |
Cruise control vs MPG | YarisOwnersDad | Fuel Economy Forum | 15 | 05-29-2009 03:55 PM |
Using Cruise control | Driver | General Yaris / Vitz Discussion | 14 | 11-09-2006 10:12 PM |