Toyota Yaris Forums - Ultimate Yaris Enthusiast Site
 

 


 
Go Back   Toyota Yaris Forums - Ultimate Yaris Enthusiast Site > Technical Forums > DIY / Maintenance / Service
  The Tire Rack

Reply
 
Thread Tools Display Modes
Old 11-12-2014, 05:07 PM   #1
joell
 
joell's Avatar
 
Drives: 2013 Hatchback
Join Date: Dec 2012
Location: Panama, Central America
Posts: 57
Question Help finding part number

Hello
The clear white plastic part that hold the rubber gromet of the hatch is loose,the water can leak inside the headliner.
I searched the catalog of parts but without luck, the part itself donīt have any marking that indicate a Toyota code XXXX-XXXX.

Silicone sealant and 3M tape cannot hold in place, Japanese Yaris 2013, sorry for the bad english





Thanks for any help
joell is offline   Reply With Quote
Old 11-14-2014, 12:09 AM   #2
bairjo
 

Join Date: Feb 2010
Posts: 547
I usually find that the local Toyota dealer can give that info in 5 minutes. try that.
bairjo is offline   Reply With Quote
Old 11-14-2014, 07:33 AM   #3
CTScott
ULTIMATE
 
CTScott's Avatar
 
Drives: 09 5dr LB, 2x 08 3dr LB
Join Date: Oct 2008
Location: USA, CT
Posts: 13,456
That white part is considered part of the complete hatch wiring harness. You can't purchase it separately from Toyota.
CTScott is offline   Reply With Quote
Old 11-14-2014, 08:11 AM   #4
hondajt
 
hondajt's Avatar
 
Drives: 2013 Yaris LE 5Dr
Join Date: Nov 2014
Location: United States
Posts: 91
You can make something out of hose sealer and silicon from Lowe's or Home Depot.
hondajt is offline   Reply With Quote
Old 11-14-2014, 09:32 AM   #5
CTScott
ULTIMATE
 
CTScott's Avatar
 
Drives: 09 5dr LB, 2x 08 3dr LB
Join Date: Oct 2008
Location: USA, CT
Posts: 13,456
Quote:
Originally Posted by hondajt View Post
You can make something out of hose sealer and silicon from Lowe's or Home Depot.
The white plastic piece snaps into a large hole in the hatch opening and is designed to squeeze the molded lip on the black rubber boot to make a waterproof seal. When the hatch is open the black boot has a significant amount of tension on it as well.

You would have a difficult time making something to replace it and particularly finding a sealing compound that will stick to the painted metal and the rubber and form a completely waterproof seal (particularly for the O.P., who is in Panama, where it is hot and wet).
CTScott is offline   Reply With Quote
Old 11-14-2014, 09:36 AM   #6
hondajt
 
hondajt's Avatar
 
Drives: 2013 Yaris LE 5Dr
Join Date: Nov 2014
Location: United States
Posts: 91
Quote:
Originally Posted by CTScott View Post
The white plastic piece snaps into a large hole in the hatch opening and is designed to squeeze the molded lip on the black rubber boot to make a waterproof seal. When the hatch is open the black boot has a significant amount of tension on it as well.

You would have a difficult time making something to replace it and particularly finding a sealing compound that will stick to the painted metal and the rubber and form a completely waterproof seal (particularly for the O.P., who is in Panama, where it is hot and wet).
Yikes, yeah, I don't think I completely understood how it operated.....so in hindsight....the better idea is definitely to go buy the harness (and part) from the dealer or online.

Good luck.
hondajt is offline   Reply With Quote
Old 11-14-2014, 12:57 PM   #7
joell
 
joell's Avatar
 
Drives: 2013 Hatchback
Join Date: Dec 2012
Location: Panama, Central America
Posts: 57
Thanks for all the responses

I will evaluate all the options available:
1. Buy the whole harness
2. Search in the junkyard, some new yaris have crashed
3.Another post have a lead for possibles replacements, partial Part Name Code (82819-XXXXX) that will investigate more.

The best advice I can give is: Be careful when installing any reverse camera
joell is offline   Reply With Quote
Old 11-14-2014, 01:15 PM   #8
Eduardo_mty
 

Join Date: Sep 2014
Posts: 198
Ctscott do you know the part number of hatch Wiring harness.

Joell i did the same "error" when i try to install reverse camera

Last edited by Eduardo_mty; 11-14-2014 at 01:57 PM.
Eduardo_mty is offline   Reply With Quote
Old 11-14-2014, 02:02 PM   #9
CTScott
ULTIMATE
 
CTScott's Avatar
 
Drives: 09 5dr LB, 2x 08 3dr LB
Join Date: Oct 2008
Location: USA, CT
Posts: 13,456
Quote:
Originally Posted by Eduardo_mty View Post
Ctscott do you know the part number of hatch Wiring harness.

Joell i did the same "error" when i try to install reverse camera
Any of these:

82184-52320
82184-52340
82184-52350
CTScott is offline   Reply With Quote
Old 11-14-2014, 06:41 PM   #10
Eduardo_mty
 

Join Date: Sep 2014
Posts: 198
I found it, www.toyotapartsoverstock.com $82.41 usd
Eduardo_mty is offline   Reply With Quote
Old 11-15-2014, 03:18 AM   #11
ucsmfu
 
Drives: yaris le
Join Date: Sep 2014
Location: vancouver, BC
Posts: 220
what is the best way to remove that plastic part when removing the reverse camera ?
ucsmfu is offline   Reply With Quote
Old 11-15-2014, 07:34 AM   #12
CTScott
ULTIMATE
 
CTScott's Avatar
 
Drives: 09 5dr LB, 2x 08 3dr LB
Join Date: Oct 2008
Location: USA, CT
Posts: 13,456
Quote:
Originally Posted by ucsmfu View Post
what is the best way to remove that plastic part when removing the reverse camera ?
Squeezing the tabs from below is the only way to remove it without deforming it.
CTScott is offline   Reply With Quote
Old 11-15-2014, 06:14 PM   #13
ucsmfu
 
Drives: yaris le
Join Date: Sep 2014
Location: vancouver, BC
Posts: 220
Quote:
Originally Posted by CTScott View Post
Squeezing the tabs from below is the only way to remove it without deforming it.
to access to the tabs below, will I need to remove the headliner ?

thanks
ucsmfu is offline   Reply With Quote
Old 11-15-2014, 09:29 PM   #14
CTScott
ULTIMATE
 
CTScott's Avatar
 
Drives: 09 5dr LB, 2x 08 3dr LB
Join Date: Oct 2008
Location: USA, CT
Posts: 13,456
Quote:
Originally Posted by ucsmfu View Post
to access to the tabs below, will I need to remove the headliner ?

thanks
Partially, or get your hand up between it and the roof.
CTScott is offline   Reply With Quote
Old 12-21-2014, 12:06 PM   #15
joell
 
joell's Avatar
 
Drives: 2013 Hatchback
Join Date: Dec 2012
Location: Panama, Central America
Posts: 57
Update: I take the broken part to a 3D printing shop, they scanned and printed in black ABS, cost $30 dollars.



joell is offline   Reply With Quote
Old 12-21-2014, 12:50 PM   #16
Eduardo_mty
 

Join Date: Sep 2014
Posts: 198
Do you have a finished printing part.


Where are you located ?
Eduardo_mty is offline   Reply With Quote
Old 12-21-2014, 12:50 PM   #17
Eduardo_mty
 

Join Date: Sep 2014
Posts: 198
Picture from finished part printing
Eduardo_mty is offline   Reply With Quote
Old 12-21-2014, 07:33 PM   #18
joell
 
joell's Avatar
 
Drives: 2013 Hatchback
Join Date: Dec 2012
Location: Panama, Central America
Posts: 57
This is the finished printed part, i dont have the computer archive of the 3D model.But you can search locally for some place that can help you: http://www.3dhubs.com/3dprint
joell is offline   Reply With Quote
Reply

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump

Similar Threads
Thread Thread Starter Forum Replies Last Post
Top glove box part number? Nips Cosmetic Modifications (Exterior/Interior) 6 02-24-2012 12:39 PM
Yet another cabin air filter part number... Goose DIY / Maintenance / Service 0 05-05-2010 05:15 PM
Part Number?? nick1983 Wheels, Tires and Suspension Forum sponsored by The Tire Rack 7 04-12-2007 01:43 PM
A quick favor... I need a part number ChinoCharles General Yaris / Vitz Discussion 5 04-10-2007 08:36 PM
HELP: JDM Armrest Console Box part number GabL Cosmetic Modifications (Exterior/Interior) 7 10-24-2006 11:12 PM


All times are GMT -4. The time now is 09:22 PM.




YarisWorld
Powered by vBulletin® Version 3.8.0
Copyright ©2000 - 2018, Jelsoft Enterprises Ltd.