I know its been asked before..but i still don't know - Toyota Yaris Forums

luckydlb · 03-12-2007, 12:15 PM

I apoligize for asking, because i know its been answered, but I still don't understand how to take of the window crank to access the front speakers in my liftback. pictures would be extremely helpful, or a step by step, just make sure a not smart person could understand it.

Thanks in advance.

ChinoCharles · 03-12-2007, 01:38 PM

You need to wedge something between the handle and that white/opaque spacer. I used a zip tie last night and it worked fine. Just work a zip tie in there and twist it around, putting pressure on the center of the crank. Eventually you'll pop the little retention clip out enough to take it out and get the handle off.

It'll take a while to get it the first time, but once you do it once it'll make more sense.

luckydlb · 03-12-2007, 01:48 PM

thanks for your help...when i read other posts i thought u had to somehow get into the door pannel and work a rag around back there...and was a bit confused....lol..

thanks again

jdubau55 · 03-12-2007, 04:24 PM

Heres a lil drawing. You put the rag between the handle and the door panel. This will catch that clip and push it off.

ChinoCharles · 03-12-2007, 04:35 PM

Quote:

Originally Posted by jdubau55

Heres a lil drawing. You put the rag between the handle and the door panel. This will catch that clip and push it off.

Good job! You get three gold stars today!

That drawing is TIGHT! Actually, its damn accurate too.

MrJester · 03-12-2007, 07:00 PM

Honestly I could not get the rag trick to work best bet is buying the stupid tool for $7-$9

KSIbucky · 03-12-2007, 09:08 PM

how does the clip keep it on there

jdubau55 · 03-12-2007, 09:33 PM

Side profile view...Clip goes around part of the crank handle something like that to keep it from easily pulling off. Thats why you must remove the clip. Othewise, you pull the whole door panel and window regulator all out.

Im a paint master....

jdubau55 · 03-12-2007, 09:35 PM

Quote:

Originally Posted by MrJester

Honestly I could not get the rag trick to work best bet is buying the stupid tool for $7-$9

You kinda have to try to look hard behind the handle to see where the ends of the clip are then put your rag on the ends so it will push it off. If you just shove the rag behind there and go for it you might be pushing in on. Once you figure it out its a breeze.

TrancosRt · 03-12-2007, 09:59 PM

The clip ends are facing the crank, so slipping the rag between the crank and the door panel grabs the ends. Then wrap the crank axis, and pull the rag back and forth until it pops out. (mind you, when it does pop up, IT REALLY does... I had to chase it!)

ChinoCharles · 03-12-2007, 11:51 PM

Yeah, don't lose that sucker.

You guys should see the inside of my car right now. The paneling is in the trunk.

Black Yaris · 03-13-2007, 12:04 AM

I think I figured out the problem on your drivers window...

The wiring was all wrong

ChinoCharles · 03-13-2007, 12:18 AM

Haha, oh I had the wiring right. Somewhere between me testing it and getting the driver's side door panel back on I must have jarred a connection loose somewhere. It'll be fun following wire around my car later. Ohhhh yeah baby, real fun.

JustYYaris · 04-28-2007, 11:23 AM

I'm not sure if this has been clearly pointed out, but the rag goes between the plastic spacer and the actual crank. After 15 minutes trying between the door and the spacer, it came to me that maybe they meant between the crank/spacer! Could just be I wasn't reading directions or wasn't getting it, but good to know! I'm in my car doing it right now, rag trick works awesome!

PS: How does it go back on? lol

spkrman · 04-28-2007, 01:13 PM

easiest is to use the tool, even a monkey could use it and pop off the crank in 30 seconds... that includes chuggin a beer.

on that note, I noobed it up and the clip flew into oblivion... the replcaement clips @ advance dont fit properly, sux.

MarkCamp · 12-09-2012, 03:05 PM

It took me about 2 seconds once I figured it out! Use a screw driver to lift the handle away from the white washer. Place the rag so the edge starts in the handle area. Pull the rag around the shaft, away from the handle. The end of the clip, which is pointed towards the handle end, will get caught and the clip will just pop out!

03-12-2007, 12:15 PM	#1
luckydlb Drives: 3dr Black Yaris Liftback Join Date: Oct 2006 Location: Syracuse - ish NY Posts: 16	I know its been asked before..but i still don't know I apoligize for asking, because i know its been answered, but I still don't understand how to take of the window crank to access the front speakers in my liftback. pictures would be extremely helpful, or a step by step, just make sure a not smart person could understand it. Thanks in advance.

03-12-2007, 09:08 PM	#7
KSIbucky View User's Garage Drives: 2007 Yaris manual dark silver Join Date: May 2006 Location: Fond du Lac, WI Posts: 694	how does the clip keep it on there __________________ 7 Color Tach Fujita Intake Momo pedals Shift knob and boot. Full TRD SSK. Blitz exhaust Megan Lowering Springs (Next is DC Header)

03-13-2007, 12:04 AM	#12
Black Yaris der Zeck View User's Garage Drives: '05 Audi A4 1.8t quattro Join Date: Sep 2006 Location: Toledo, OH Posts: 5,231	I think I figured out the problem on your drivers window... The wiring was all wrong __________________

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
Anyone have Yaris air and oil filter numbers?	Yaris_Fan	DIY / Maintenance / Service	54	02-11-2009 01:14 AM
sum dude asked if my car was electric...	Blenjar	General Yaris / Vitz Discussion	17	01-12-2007 10:39 PM
How often do you get asked "is that a Yaris?"	Jfoofoo	General Yaris / Vitz Discussion	23	12-14-2006 11:11 PM
This is my buying experience	yoyoche	New YARIS Purchase Forum	9	08-13-2006 08:01 PM
How much do you think they make?	Chaad32	New YARIS Purchase Forum	38	08-05-2006 08:50 AM

03-12-2007, 01:38 PM	#2
ChinoCharles Banned Drives: LB Join Date: Jul 2006 Location: OH Posts: 7,787	You need to wedge something between the handle and that white/opaque spacer. I used a zip tie last night and it worked fine. Just work a zip tie in there and twist it around, putting pressure on the center of the crank. Eventually you'll pop the little retention clip out enough to take it out and get the handle off. It'll take a while to get it the first time, but once you do it once it'll make more sense.

03-12-2007, 01:48 PM	#3
luckydlb Drives: 3dr Black Yaris Liftback Join Date: Oct 2006 Location: Syracuse - ish NY Posts: 16	thanks for your help...when i read other posts i thought u had to somehow get into the door pannel and work a rag around back there...and was a bit confused....lol.. thanks again

03-12-2007, 07:00 PM	#6
MrJester View User's Garage Drives: homo Join Date: Feb 2007 Location: Homo Posts: 149	Honestly I could not get the rag trick to work best bet is buying the stupid tool for $7-$9

03-12-2007, 09:59 PM	#10
TrancosRt View User's Garage Drives: 07 Silver HB Yaris Join Date: Jul 2006 Location: S Florida Posts: 289	The clip ends are facing the crank, so slipping the rag between the crank and the door panel grabs the ends. Then wrap the crank axis, and pull the rag back and forth until it pops out. (mind you, when it does pop up, IT REALLY does... I had to chase it!)

03-12-2007, 11:51 PM	#11
ChinoCharles Banned Drives: LB Join Date: Jul 2006 Location: OH Posts: 7,787	Yeah, don't lose that sucker. You guys should see the inside of my car right now. The paneling is in the trunk.

03-13-2007, 12:18 AM	#13
ChinoCharles Banned Drives: LB Join Date: Jul 2006 Location: OH Posts: 7,787	Haha, oh I had the wiring right. Somewhere between me testing it and getting the driver's side door panel back on I must have jarred a connection loose somewhere. It'll be fun following wire around my car later. Ohhhh yeah baby, real fun.

04-28-2007, 11:23 AM	#14
JustYYaris View User's Garage Drives: 2007 Blazing Blue Hatch M/T Join Date: Jan 2007 Location: Spencer, NY Posts: 61	I'm not sure if this has been clearly pointed out, but the rag goes between the plastic spacer and the actual crank. After 15 minutes trying between the door and the spacer, it came to me that maybe they meant between the crank/spacer! Could just be I wasn't reading directions or wasn't getting it, but good to know! I'm in my car doing it right now, rag trick works awesome! PS: How does it go back on? lol

04-28-2007, 01:13 PM	#15
spkrman Banned View User's Garage Drives: 1 Join Date: Nov 2006 Location: 2 Posts: 1,476	easiest is to use the tool, even a monkey could use it and pop off the crank in 30 seconds... that includes chuggin a beer. on that note, I noobed it up and the clip flew into oblivion... the replcaement clips @ advance dont fit properly, sux.

12-09-2012, 03:05 PM	#16
MarkCamp I've made a post! Drives: 2007 Yaris Hatchback Join Date: Dec 2012 Location: Auburn, CA Posts: 1	It took me about 2 seconds once I figured it out! Use a screw driver to lift the handle away from the white washer. Place the rag so the edge starts in the handle area. Pull the rag around the shaft, away from the handle. The end of the clip, which is pointed towards the handle end, will get caught and the clip will just pop out!