Toyota Yaris Forums - Ultimate Yaris Enthusiast Site
 

 


 
Go Back   Toyota Yaris Forums - Ultimate Yaris Enthusiast Site > Technical Forums > DIY / Maintenance / Service
  The Tire Rack

Reply
 
Thread Tools Display Modes
Old 02-23-2016, 03:01 PM   #1
Yaris1234
 
Drives: Toyota Yaris 05
Join Date: Mar 2015
Location: Sweden
Posts: 4
What have I done?

Hello. I have a 2005 Yaris. I suspected a bad wheel bearing and thought about lifting up the car with help from a jack. I placed myself on the left hand side at the front and placed the jack under (from what I thought was a strong point in the construction) a circular little point (picture). I started to pump and the car lifted slowly. Something didn't feel right so I lowered the car back down to the ground. I looked under where the jack had been and saw that I had made a big dent, going right up, close where the drivers left foot is placed.

I think I have hurt some kind of soft metal, as you can see from the pictures there are cracks along the circular "thing?" also a bit along side on the first picture to the upper right (red marking). Have I breached something serious? I guess I don't want moisture traveling up there through the cracks...?

Please help me sort out what I have done and how serious this is.
Attached Images
File Type: jpg image1.JPG (562.2 KB, 176 views)
File Type: jpg image2.JPG (451.2 KB, 171 views)
Yaris1234 is offline   Reply With Quote
Old 02-23-2016, 03:29 PM   #2
Kar98
 
Drives: 2011 Scion tC
Join Date: Jul 2012
Location: DFW
Posts: 651
Where you are supposed to put the jack:



I'm not even sure how you managed to do what you did.
Kar98 is offline   Reply With Quote
Old 02-23-2016, 03:33 PM   #3
brushforhire
 
Drives: 07 HB YARIS, 15 JUKE, 00 TUNDR
Join Date: Mar 2007
Location: Johnstown, PA
Posts: 320
The round thing is a body plug. Just rubber plug that can be pulled out to drain out excess water. You might need to pull the carpet back there to make sure it is seated properly if you can't tell from the bottom.

The long "crack" on the side just looks like where the floorpan meets the rocker panel. Looks more like the undercoating is cracking that anything else.

I would say you probably just scratched the metal a little around the body plug.
brushforhire is offline   Reply With Quote
Old 02-23-2016, 05:08 PM   #4
WeeYari
 
WeeYari's Avatar
 
Drives: 06 Polar White 5dr, 13 Soul 4u
Join Date: Oct 2008
Location: Georgetown, Ontario, Canada
Posts: 5,739
^ this

No damage done. Just get yourself a rattle can of rust-proofing and spray those areas you've outlined in red.
__________________
WeeYari is offline   Reply With Quote
Old 02-23-2016, 05:16 PM   #5
tmontague
 
tmontague's Avatar
 
Drives: '08 2zr swapped Vios M/T
Join Date: Oct 2012
Location: Caledonia Ont.
Posts: 2,938
^ definitely spray the area to avoid corrosion.

I don't personally put jack stands under the pinch welds. IMO they're only good for road side emergencies. I put stands under the control arms for the front, or the subframe if I need access to the control arms.

I put my Jack under the pinch welds but only to jack up and down the car. I also cut a slit in a rubber hockey puck so that no damage is done to the pinch welds.

For the rear of the car, use the little piece of metal coming down in the middle of the back of the car. Then put your stands under the axles. Works well and keeps everything sturdy.

I've heard of others using the square frame rails that run under the car just in from the pinch welds. This should be fine since the Yaris is such a light car.
__________________
No one ever wants to give a Yaris the point by...
tmontague is offline   Reply With Quote
Old 02-24-2016, 06:33 AM   #6
Yaris1234
 
Drives: Toyota Yaris 05
Join Date: Mar 2015
Location: Sweden
Posts: 4
Thank you!
Yaris1234 is offline   Reply With Quote
Old 02-24-2016, 09:37 AM   #7
Bluevitz-rs
1NZ-6spd
 
Bluevitz-rs's Avatar
 
Drives: '05 6-Spd Vitz RS
Join Date: Oct 2008
Location: Oshawa, Ontario, Canada
Posts: 2,966
put the jack under the big square frame rails.
Bluevitz-rs is offline   Reply With Quote
Old 02-24-2016, 02:39 PM   #8
bronsin
 
bronsin's Avatar
 
Drives: 2009 Base Hatch 2 Dr Auto
Join Date: Dec 2008
Location: nj
Posts: 4,790
"And you may ask yourself "My God, what have I done?""

Talking Heads
__________________
Synthetic Oil: Its All In Your Head
bronsin is offline   Reply With Quote
Old 02-25-2016, 04:51 PM   #9
xdarkxfirex
 
Drives: 2015 yaris le
Join Date: Feb 2015
Location: hamilton, on
Posts: 149
No damage at all. I jack up my car from other places, and you can see a few small dents here and there, but it doesnt effect the car whatsoever. Even the subframe bends a little when I jack it up from there. Toyota should've used stronger metal. As long as you dont jack it from obvious places, like the oil pans, brake/fuel lines etc, you should be fine. It you are worried about any damage, just jack it up from somewhere really solid. Even the pinch welds bend a bit
xdarkxfirex is offline   Reply With Quote
Old 02-25-2016, 10:02 PM   #10
CoryM
 
Drives: 2009 5-door, 5-speed
Join Date: Sep 2011
Location: White Rock BC
Posts: 687
I'm guessing you've had a BMW or similar? They use round black "jacking pads" which look a bit like the rubber plug you went for.

As others have said, you're fine. Next time, try the subframe.

Cheers.
CoryM is offline   Reply With Quote
Old 02-27-2016, 05:01 AM   #11
Secretblend
 
Drives: 2009 Yaris
Join Date: Apr 2015
Location: United States
Posts: 23
Here is locations of where you can place jack and jack stands on your car.
Attached Files
File Type: pdf lift and jack stand.pdf (213.1 KB, 41 views)
Secretblend is offline   Reply With Quote
Reply

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -4. The time now is 07:52 AM.




YarisWorld
Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2024, vBulletin Solutions Inc.