DIY - 1.8L 1ZZ-FE TB Connector Chip Swap - Page 17 - Toyota Yaris Forums

MGargano · 06-06-2009, 01:23 AM

Quote:

Originally Posted by jkuchta

turn the screw clockwise a half turn with the engine off. That should make it better. Also, if a half turn isnt enough, keep turning in half turn increments (with the engine off).

I gave up on the 1ZZ for the 2nd time. No matter how many turns I gave the idle screw, after a while the engine would settle back down to around 500 RPM, shake/shudder, rev up to 1,000 RPM, and then repeat the process until I either started moving or turned the car off in frustration. I hate all the problems I'm having since the performance of the the 1ZZ really is noticeably better than OEM, but I can't take the way it idles. I was also getting the heavy jerking whenever I took my foot off the gas.

PETERPOOP · 06-06-2009, 12:54 PM

you might have gotten a bad throttle body. maybe you should order the one through cali yaris.

MGargano · 06-06-2009, 01:39 PM

Quote:

Originally Posted by PETERPOOP

you might have gotten a bad throttle body. maybe you should order the one through cali yaris.

I don't think it's that, since the TB was working perfectly until I disconnected the battery. I wasn't getting any oscillation, jerking, weird idling, or CEL... then I pulled the battery cable and all these problems came out of the woodwork. I might try the swap again down the road sometime. Where can I get the Micro Image one? I don't see it listed on his website. Is it new or used/refurbished?

jkuchta · 06-07-2009, 01:17 PM

It's a 1zz TB, with the Yaris chip module already swapped on...also, we remove all of the epoxy on the idle set screw and make a preliminary adjustment to get you in the ballpark.

PETERPOOP · 07-05-2009, 01:37 PM

finally installed my 1zz tb after months of it sitting in my room. no CELS. warm idle at 2500rpms, then within seconds drops to 2k rpms, and then idles smoothly at a warm idle of 585 rpms. Didn't adjust the idle screw, and I didn't switch the chips; I think i've lucked out....

Drove the car after and ran it hard and conservatively, no problems! niceee

edit: Still running good. I don't really notice an increase in power? I remember looking at Yoda's dyno sheet that he did after he added the 1zz TB, and he got a gain of 3 whp. Unless I got less of a gain, I can't really feel 3 whp added to the existing. However, if the car keeps running with no problems for a couple of weeks, I plan on taking it to get dyno'd. Now that I have my 1zz injectors, I will be able to successfully do three pulls and hopefully hit 140whp now with the 1zz TB! :)

blacksandiegovitz · 07-17-2009, 09:16 PM

Quote:

Originally Posted by echo_hrs

I got my TB yesterday & cleaned and polished it...I need to go get a coupler for the intake to TB, is it a 2.25" - 2.5" I need?

Anything else I need for the swap?

I'm thinking I'll just do the straight swap like PETERPOOP and see what I get before swapping chips...

Cheers

I just did this swap today and Its feels a lot stronger. I was able to make my aem coupler strech over the corolla tb .
you'll also need either 6 rivets and a rivet gun or 6 x small bolt and nuts for the "chip swap "

jkuchta · 07-19-2009, 05:25 PM

I used 6-32 allen head cap screws and jet nuts on mine. Makes for a realy clean job and the jet nuts are self-locking, so no worries about the screws coming loose.

whooppee777 · 07-20-2009, 08:56 PM

where the hell did the diy go?

PETERPOOP · 07-20-2009, 09:26 PM

t-sport is at it again; deleting everything he posts. i wouldn't think he'd delete this!

mikenacarato · 07-20-2009, 09:27 PM

why did he do that?

whooppee777 · 07-20-2009, 11:54 PM

ditto

Kioshi · 07-21-2009, 02:44 PM

Quote:

Originally Posted by mikenacarato

why did he do that?

Wants to be the only one w/ the setup/s...or it backfired on him...or something else?

jkuchta · 07-21-2009, 02:55 PM

I've got close to 10,000 miles on my chipped 1ZZ TB, so I don't think it went bad on him.

PatrickJohnson · 07-21-2009, 03:13 PM

I'm hoping he just removed it because so many are having issues and not because he is being a pissant...

whooppee777 · 07-21-2009, 07:21 PM

i just did a swap last night from the stock throttle position sensor to a scion tc throttle body. i havent put the throttle body on yet to see it worked though. my corolla throttle body didnt set any cels when i installed it as is

PETERPOOP · 07-21-2009, 09:28 PM

my 1zz throttle body that i put on without switching the chip or adjusting the idle screw and was running perfectly for the last two weeks has just turned gay on me. It started oscilating the other day, and i unplugged the battery, replugged it and it was fine. However, again it is now back to oscilating and i can't disturb it by tapping the gas to interupt it. my only hope now is to do a chip swap; but i don't think i want to.

eii · 07-21-2009, 09:48 PM

Quote:

Originally Posted by PatrickJohnson

I'm hoping he just removed it because so many are having issues and not because he is being a pissant...

Na, he always does this. We're not sure why he does though.

Quote:

Originally Posted by PETERPOOP

my 1zz throttle body that i put on without switching the chip or adjusting the idle screw and was running perfectly for the last two weeks has just turned gay on me. It started oscilating the other day, and i unplugged the battery, replugged it and it was fine. However, again it is now back to oscilating and i can't disturb it by tapping the gas to interupt it. my only hope now is to do a chip swap; but i don't think i want to.

Why wouldnt you? I didnt even bother trying it with the stock 1zz chip since I heard almost everyone's problems being fixed by a swap. Swap it!

blacksandiegovitz · 07-21-2009, 10:00 PM

Quote:

Originally Posted by eii

Why wouldnt you? I didnt even bother trying it with the stock 1zz chip since I heard almost everyone's problems being fixed by a swap. Swap it!

Just do the damn swap already Peter

07-05-2009, 01:37 PM	#293
PETERPOOP View User's Garage Drives: 08 white liftback Join Date: Oct 2008 Location: Oahu Posts: 3,674	finally installed my 1zz tb after months of it sitting in my room. no CELS. warm idle at 2500rpms, then within seconds drops to 2k rpms, and then idles smoothly at a warm idle of 585 rpms. Didn't adjust the idle screw, and I didn't switch the chips; I think i've lucked out.... Drove the car after and ran it hard and conservatively, no problems! niceee edit: Still running good. I don't really notice an increase in power? I remember looking at Yoda's dyno sheet that he did after he added the 1zz TB, and he got a gain of 3 whp. Unless I got less of a gain, I can't really feel 3 whp added to the existing. However, if the car keeps running with no problems for a couple of weeks, I plan on taking it to get dyno'd. Now that I have my 1zz injectors, I will be able to successfully do three pulls and hopefully hit 140whp now with the 1zz TB! :) Last edited by PETERPOOP; 07-05-2009 at 08:48 PM.

07-20-2009, 08:56 PM	#296
whooppee777 I used to have 1700 posts View User's Garage Drives: 2008 Yaris Hatch Join Date: Apr 2007 Location: Maryland Posts: 808	where the hell did the diy go? __________________ *First Boosted Yaris On The East Coast*

07-20-2009, 11:54 PM	#299
whooppee777 I used to have 1700 posts View User's Garage Drives: 2008 Yaris Hatch Join Date: Apr 2007 Location: Maryland Posts: 808	ditto __________________ *First Boosted Yaris On The East Coast*

07-21-2009, 07:21 PM	#303
whooppee777 I used to have 1700 posts View User's Garage Drives: 2008 Yaris Hatch Join Date: Apr 2007 Location: Maryland Posts: 808	i just did a swap last night from the stock throttle position sensor to a scion tc throttle body. i havent put the throttle body on yet to see it worked though. my corolla throttle body didnt set any cels when i installed it as is __________________ *First Boosted Yaris On The East Coast*

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
1.8L Engine Swap, Possible?	Yaris T-Sport	Performance Modifications	4	05-06-2007 06:57 PM
swap for 2zz-ge????	yarisTOONR82	Performance Modifications	12	03-23-2007 07:15 PM

06-06-2009, 12:54 PM	#290
PETERPOOP View User's Garage Drives: 08 white liftback Join Date: Oct 2008 Location: Oahu Posts: 3,674	you might have gotten a bad throttle body. maybe you should order the one through cali yaris.

06-07-2009, 01:17 PM	#292
jkuchta View User's Garage Drives: 2007 Yaris hatch (red) Join Date: Sep 2007 Location: L.A. Posts: 557	It's a 1zz TB, with the Yaris chip module already swapped on...also, we remove all of the epoxy on the idle set screw and make a preliminary adjustment to get you in the ballpark.

07-19-2009, 05:25 PM	#295
jkuchta View User's Garage Drives: 2007 Yaris hatch (red) Join Date: Sep 2007 Location: L.A. Posts: 557	I used 6-32 allen head cap screws and jet nuts on mine. Makes for a realy clean job and the jet nuts are self-locking, so no worries about the screws coming loose.

07-20-2009, 09:26 PM	#297
PETERPOOP View User's Garage Drives: 08 white liftback Join Date: Oct 2008 Location: Oahu Posts: 3,674	t-sport is at it again; deleting everything he posts. i wouldn't think he'd delete this!

07-20-2009, 09:27 PM	#298
mikenacarato SIPNDEW View User's Garage Drives: 15 STI Join Date: Oct 2008 Location: Brentwood, TN Posts: 2,281	why did he do that?

07-21-2009, 02:55 PM	#301
jkuchta View User's Garage Drives: 2007 Yaris hatch (red) Join Date: Sep 2007 Location: L.A. Posts: 557	I've got close to 10,000 miles on my chipped 1ZZ TB, so I don't think it went bad on him.

07-21-2009, 03:13 PM	#302
PatrickJohnson Drives: 2008 Yaris LB Join Date: Dec 2008 Location: Murfreesboro, TN Posts: 198	I'm hoping he just removed it because so many are having issues and not because he is being a pissant...

07-21-2009, 09:28 PM	#304
PETERPOOP View User's Garage Drives: 08 white liftback Join Date: Oct 2008 Location: Oahu Posts: 3,674	my 1zz throttle body that i put on without switching the chip or adjusting the idle screw and was running perfectly for the last two weeks has just turned gay on me. It started oscilating the other day, and i unplugged the battery, replugged it and it was fine. However, again it is now back to oscilating and i can't disturb it by tapping the gas to interupt it. my only hope now is to do a chip swap; but i don't think i want to.