Toyota Yaris Forums - Ultimate Yaris Enthusiast Site
 

 


 
Go Back   Toyota Yaris Forums - Ultimate Yaris Enthusiast Site > Technical Forums > DIY / Maintenance / Service
  The Tire Rack

Reply
 
Thread Tools Display Modes
Old 09-08-2018, 11:05 PM   #1
brad14880
 
Drives: 2009 Toyota Yaris Hatchback
Join Date: Jun 2018
Location: SCIO NY
Posts: 4
BRAKE PAD AND ROTOR GOUGING INSIDE SIDE OF ROTOR

Hello all,
I am new to the forum, and have came here for numerous answered questions by just searching, well i have a question that may be able to be answered here...
History:
Replaced front pads/rotors
Replaced front passenger side wheel bearing
Replaced front tires

Problem:
Brake rotor has a defined gouge on the inner side of the rotor.
When you are making a hard left turn, the brakes are rubbing, if you apply pressure to the pedal, the noise stops..

I have replaced the front rotor and pads on that side 2x and its still doing it.

I have torn the wheel off myself, along with the braking system to see if there was anything out of the ordinary with it- (brake dust shield, sticking caliper piston, sticky slider bolts, faulty brake pad hardware) and NOTHING

The dust shield has been loose, and to improvise until i get time to pull the knuckle back off, drilled and tapped one bolt on the worse side of it to hold it in place as it has rusted terribly. I have put car on lift and VERIFIED there is no contact between the rotor and dust shield.

Again, replaced the faulty wheel bearing, and with the new bearing/hub (bought both and used both new to save time)
Ever since then, the car has been gouging the rotor on the inside of the vehicle.

SO HOPEFULLY SOMEONE ELSE CAN HELP ME POSSIBLY SEE IF I AM MISSING ANYTHING TO LOOK OVER...

THANKS FOR YOUR ADVICE, AND I'M TERRIBLY SORRY FOR THE LONG ASS POST...

-Brad
brad14880 is offline   Reply With Quote
Old 09-09-2018, 09:02 AM   #2
IllusionX
It's the illusion you see
 
Drives: 07 Yaris Sedan Aero
Join Date: Oct 2006
Location: Brossard, QC
Posts: 3,888
Push the shield further back.

Mine clearly have space between, but rubs when making hard right turn (left shield rubs)

I pushed the shield further back and it's no longer doing it.

Next I may just get brand new shield.

Sent from my VTR-L09 using Tapatalk
__________________
IllusionX is offline   Reply With Quote
Old 09-09-2018, 09:38 AM   #3
ex-x-fire
 
Drives: 2010 yaris 3 door hatch
Join Date: Jun 2013
Location: Sheboygan Falls, Wi.
Posts: 504
Maybe the bearing is tight enough. Is there any play? Do you see marks on the caliper bracket? A bracket bolt that is too long?
ex-x-fire is offline   Reply With Quote
Old 09-09-2018, 10:02 PM   #4
brad14880
 
Drives: 2009 Toyota Yaris Hatchback
Join Date: Jun 2018
Location: SCIO NY
Posts: 4
The shield does not hit, the gouging marks are nowhere on the shield and wouldn't be on the pads as well if it were to hit. I drilled and tapped two bolts way back to hold it.

I'm unsure of how the wheel bearing could be too tight. The tolerances are pretty simple it only goes in so far into hun and into spindle...

SO CONFUSING
brad14880 is offline   Reply With Quote
Old 09-09-2018, 11:26 PM   #5
IllusionX
It's the illusion you see
 
Drives: 07 Yaris Sedan Aero
Join Date: Oct 2006
Location: Brossard, QC
Posts: 3,888
Quote:
Originally Posted by brad14880 View Post
The shield does not hit, the gouging marks are nowhere on the shield and wouldn't be on the pads as well if it were to hit. I drilled and tapped two bolts way back to hold it.

I'm unsure of how the wheel bearing could be too tight. The tolerances are pretty simple it only goes in so far into hun and into spindle...

SO CONFUSING
Remove the shield. You'll know right away if that was the problem.
Like I said, mine did it on hard turn. I pryed it away from the rotor and the noise stopped.

Sent from my VTR-L09 using Tapatalk
__________________
IllusionX is offline   Reply With Quote
Old 09-12-2018, 10:47 PM   #6
brad14880
 
Drives: 2009 Toyota Yaris Hatchback
Join Date: Jun 2018
Location: SCIO NY
Posts: 4
********UPDATE******
I HAVE NARROWED IT DOWN TO THE ROTOR RUBBING ON THE CALIPER BRACKET, INSIDE CORNER TOP PORTION OF THE ROTOR AND THE BRACKET,

COULD THE MOUNTING EARS OF THE KNUCKLE HAVE BEEN BENT WHILE PRESSING THE BEARING IN OR OUT?
I AM GOING TO GRIND THE BRACKET OUT A FEW MILS TO GET IT TO STOP RUBBING UNTIL I CAN GET A NEW KNUCKLE...
brad14880 is offline   Reply With Quote
Old 09-12-2018, 11:10 PM   #7
CoryM
 
Drives: 2009 5-door, 5-speed
Join Date: Sep 2011
Location: White Rock BC
Posts: 687
Quote:
Originally Posted by brad14880 View Post
,

COULD THE MOUNTING EARS OF THE KNUCKLE HAVE BEEN BENT WHILE PRESSING THE BEARING IN OR OUT?
Yes.
CoryM is offline   Reply With Quote
Reply

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -4. The time now is 06:07 AM.




YarisWorld
Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2024, vBulletin Solutions Inc.