Part #s for Fog Light install? Can anyone who works for Toyota confirm? - Page 4 - Toyota Yaris Forums

CTScott · 01-23-2010, 03:03 PM

Quote:

Originally Posted by IsLNdbOi

There used to be some threads here on YW w/ pictures on removing the steering wheel, the stock stalk and then replacing the stalk w/ a new one. Can't find those threads anymore.

Anyone have links to or have the pics. from those threads?

Take a look through the cruise control threads. I believe in one of them that there are some good pics of removing the steering wheel.

1NZYaris1 · 01-24-2010, 12:57 AM

Quote:

Originally Posted by IsLNdbOi

There used to be some threads here on YW w/ pictures on removing the steering wheel, the stock stalk and then replacing the stalk w/ a new one. Can't find those threads anymore.

Anyone have links to or have the pics. from those threads?

Here you go here is the toyota PDF
for Steering wheel fitting /Removing

IsLNdbOi · 01-24-2010, 04:06 AM

Thanks guys. The part of the process I'm actually looking for is removal of the original combination switch and installation of the new one w/ the fog light control.

CTScott · 01-24-2010, 08:00 AM

Quote:

Originally Posted by IsLNdbOi

Thanks guys. The part of the process I'm actually looking for is removal of the original combination switch and installation of the new one w/ the fog light control.

That's the easy part. Once the wheel is off, there are just two plastic tabs that hold the switch. You release those and pop the connector.

IsLNdbOi · 01-27-2010, 10:48 AM

Got the fog light kit yesterday and I'm not happy with it. On my '07 LB, each fog light mounting hole / spot had two slits where the tabs on each fog light would slide into while the other side would be screwed in.

So, the fog lights for the '07 would have two tabs on each side. On my '09 5-door LB, each fog light mounting hole / spot has one slit where a tab on each fog light should go. The fog lights that came with this kit has two tabs on each side just like the ones for the '07 / '08 LB. For them to fit properly, they should have only one tab on each side. The tab on one side would insert into the slit on the mounting hole and the tab on the opposite side would be screwed into the screw hole on the mounting hole. So, once I installed these fog lights there was a noticeable gap b/w the lights and the bumper. Also, the top edge of the fog bezels pop out a little bit so there's a slight gap b/w the top edge of the bezels and the bumper. I already checked and all the tabs are pushed all the way in, securing the bezels. I don't recommend this kit.

cali yaris · 01-27-2010, 11:40 AM

I believe the gap is common to all, not just the 2009 and up.

spookz · 01-27-2010, 06:01 PM

The tiny gap is probably so that the heat from the foglamp glass doesn't melt the bezel plastic..

As for the tiny gap on the top edge of the bezel and the bumper, that's normal. I have genuine '09 bezels and they too leave a tiny gap.

IsLNdbOi · 01-30-2010, 02:21 PM

I don't remember there being gaps like this on my '07 LB. Here are some quick pics. I took:

Revsson · 08-20-2010, 11:50 PM

Quote:

Originally Posted by CTScott

I believe that you can use either the 06-08 (84140-52150) or 09 (84140-52151) versions. TRDsparks sells the 06-08 one for $77. The difference may just be in labeling like the wiper stalk I put on mine. I bought the older version of the Prius wiper stalk and it has text on it, whereas the newer version just has the symbols.

The other place to try is the junkyard that I bought my wiper stalk from (for $50 vs ~$100). http://autoworksinc.com/

Hey CTScott -
Sorry to dredge up an older post, but when you ordered from this junkyard,
did you specify the part number or just the Prius wiper stalk with fog switch?

I don't know if I have the guts to take off the steering wheel to do this,

but that junkyard isn't too far from me, and I have a buddy that lives in the
Madison,WI area. I ordered the fog light kit from Garm, and might just put
the switch that comes in the kit for now.

CTScott · 08-21-2010, 07:27 AM

Quote:

Originally Posted by Revsson

Hey CTScott -
Sorry to dredge up an older post, but when you ordered from this junkyard,
did you specify the part number or just the Prius wiper stalk with fog switch?

I don't know if I have the guts to take off the steering wheel to do this,

but that junkyard isn't too far from me, and I have a buddy that lives in the
Madison,WI area. I ordered the fog light kit from Garm, and might just put
the switch that comes in the kit for now.

He had the part number listed, so I checked that out. The Prius wiper stalk works on the Yaris, but the headlight stalk does not, as it has different connectors.

mari · 09-27-2010, 12:04 PM

Quote:

Originally Posted by BLAZINBLUEVITZ

STALK: 84140-52151
RELAY: 90080-87026
SHROUD LH: 81482-52260
SHROUD RH: 81481-52330

I want foglights on my 2010 Sedan, and want to confirm these part numbers are also valid for my car.

Oh, and is there an OEM toyota part number for the foglight wiring harness? I assume that with the new foglight stalk, there is no need for an interior wiring harness.

1NZYaris1 · 09-27-2010, 04:50 PM

Quote:

Originally Posted by mari

I want foglights on my 2010 Sedan, and want to confirm these part numbers are also valid for my car.

Oh, and is there an OEM toyota part number for the foglight wiring harness? I assume that with the new foglight stalk, there is no need for an interior wiring harness.

Ifyou get the latest kit from Micro Image (a sponsor of this site )
everything is in the kit apart from the OEM Stalk
which is not required , and the whole kit is nplug and play

mari · 09-29-2010, 01:00 PM

thanks... kit price is excellent for the wires and covers, but I like the oem stalk (its only $90 online!) and my own lights (visionx solstice LEDs).

SimTronik · 10-01-2010, 04:21 PM

Just installed my fog light kit and i just noticed gaps like that. Do i need to order the original toyota bezel? Very disapointed. Help!

Quote:

Originally Posted by IsLNdbOi

I don't remember there being gaps like this on my '07 LB. Here are some quick pics. I took:

CTScott · 10-01-2010, 07:03 PM

My genuine Toyota ones fit properly around the outside, but have the same gap around the lens (which may be intentional to avoid melting the plastic).

SimTronik · 10-01-2010, 08:38 PM

Where can i get some genuine ones. are they expensive? Only the bezel.

CTScott · 10-01-2010, 08:40 PM

Quote:

Originally Posted by SimTronik

Where can i get some genuine ones. are they expensive? Only the bezel.

Read above in the thread for the part numbers. They are about $26 each from your local dealer.

chrisj · 10-04-2010, 12:30 AM

I got the MI kit for my '09 and had them professionally installed. There is the slight gap right above the fog light bezel on each light.

01-27-2010, 11:40 AM	#60
cali yaris ULTIMATE View User's Garage Drives: 07 Yaris Turbo Join Date: May 2007 Location: Canoga Park, CA Posts: 14,859	I believe the gap is common to all, not just the 2009 and up. __________________ Micro Image forums, online store and shop are now closed. It was a great eight year run, but it was time to focus on other things. I'm still selling parts on eBay under micro*image seller ID and customers can still make requests for anything specific.

01-27-2010, 06:01 PM	#61
spookz JDM yO! View User's Garage Drives: '09 3dr. 5-spd Join Date: Oct 2008 Location: Sydney, Australia Posts: 331	The tiny gap is probably so that the heat from the foglamp glass doesn't melt the bezel plastic.. As for the tiny gap on the top edge of the bezel and the bumper, that's normal. I have genuine '09 bezels and they too leave a tiny gap. __________________ .

10-04-2010, 12:30 AM	#72
chrisj Hooch Brewer-Shine Sipper View User's Garage Drives: 2009 5-dr LB Join Date: Aug 2010 Location: S. Jesus, Kentucky Posts: 646	I got the MI kit for my '09 and had them professionally installed. There is the slight gap right above the fog light bezel on each light. __________________

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
DIY (08' USDM Liftback): ESUSE Fog Light Install v2.0	goku87	DIY / Maintenance / Service	127	02-19-2023 07:01 PM
Compilation of Yaris How-tos/DIYs	YarisBueller	DIY / Maintenance / Service	39	04-28-2018 08:47 AM
Fog light install	07yaris_fe	Cosmetic Modifications (Exterior/Interior)	10	07-20-2010 01:18 PM
Looking for the Toyota Fog Light install	RocknRollRon	DIY / Maintenance / Service	33	06-13-2010 06:46 PM
srs / airbag light after head unit install?	KwonSau	In Car Entertainment + Electronics (audio / video / alarm)	7	12-24-2008 02:04 AM

01-24-2010, 04:06 AM	#57
IsLNdbOi Drives: Polar White - 5 Door '09 LB Join Date: Aug 2006 Location: Las Vegas, NV Posts: 1,285	Thanks guys. The part of the process I'm actually looking for is removal of the original combination switch and installation of the new one w/ the fog light control.

01-27-2010, 10:48 AM	#59
IsLNdbOi Drives: Polar White - 5 Door '09 LB Join Date: Aug 2006 Location: Las Vegas, NV Posts: 1,285	Got the fog light kit yesterday and I'm not happy with it. On my '07 LB, each fog light mounting hole / spot had two slits where the tabs on each fog light would slide into while the other side would be screwed in. So, the fog lights for the '07 would have two tabs on each side. On my '09 5-door LB, each fog light mounting hole / spot has one slit where a tab on each fog light should go. The fog lights that came with this kit has two tabs on each side just like the ones for the '07 / '08 LB. For them to fit properly, they should have only one tab on each side. The tab on one side would insert into the slit on the mounting hole and the tab on the opposite side would be screwed into the screw hole on the mounting hole. So, once I installed these fog lights there was a noticeable gap b/w the lights and the bumper. Also, the top edge of the fog bezels pop out a little bit so there's a slight gap b/w the top edge of the bezels and the bumper. I already checked and all the tabs are pushed all the way in, securing the bezels. I don't recommend this kit.

01-30-2010, 02:21 PM	#62
IsLNdbOi Drives: Polar White - 5 Door '09 LB Join Date: Aug 2006 Location: Las Vegas, NV Posts: 1,285	I don't remember there being gaps like this on my '07 LB. Here are some quick pics. I took:

09-29-2010, 01:00 PM	#67
mari Drives: 2010 sedan Join Date: Sep 2010 Location: LA Posts: 17	thanks... kit price is excellent for the wires and covers, but I like the oem stalk (its only $90 online!) and my own lights (visionx solstice LEDs).

10-01-2010, 07:03 PM	#69
CTScott ULTIMATE View User's Garage Drives: 09 5dr LB, 2x 08 3dr LB Join Date: Oct 2008 Location: USA, CT Posts: 13,460	My genuine Toyota ones fit properly around the outside, but have the same gap around the lens (which may be intentional to avoid melting the plastic).

10-01-2010, 08:38 PM	#70
SimTronik Machinist View User's Garage Drives: Yaris sedan 2010 Join Date: Sep 2010 Location: Sts-Anges, Quebec, canada Posts: 198	Where can i get some genuine ones. are they expensive? Only the bezel.