Toyota Yaris Forums - Ultimate Yaris Enthusiast Site
 

 


 
Go Back   Toyota Yaris Forums - Ultimate Yaris Enthusiast Site > Third Generation Toyota Yaris Main Rooms > Third Gen Yaris General Discussion
  The Tire Rack

Reply
 
Thread Tools Display Modes
Old 06-11-2018, 01:00 AM   #55
Dliverance
 
Drives: 2012 Black sand pearl <3
Join Date: Feb 2018
Location: Elma Washington
Posts: 136
So the supercharger kit is for a 2ng gen and I didn’t realize the ecu’s were different between the 2nd and third gen. The piggyback needs tapped into the tach, maf, o2 sensor, and power. I was able to figure out all of the 2nd gen wiring but I can’t find a pinout for a 2012 ecu anywhere.

The previous owner also said that power enterprise told him to leave out the wire for the o2 to get rid of the check engine light that he was having. This seems odd to me. The controller tricks the maf and has a vacuum line hooked up to see how much boost it’s making but it doesn’t seem right to not have the controller hooked up to the o2.

I’m going to keep looking for a 2012 ecu pinout and try to get in touch with power enterprise tomorrow. I don’t feel right without the controller knowing if it’s adding the right amount of fuel.
Dliverance is offline   Reply With Quote
Old 06-11-2018, 11:44 AM   #56
DarkShadowFox
Banned
 
Drives: 2015 Yaris LE 3door 1F7
Join Date: Feb 2017
Location: Massachusetts
Posts: 963
Quote:
Originally Posted by Dliverance View Post
So the supercharger kit is for a 2ng gen and I didn’t realize the ecu’s were different between the 2nd and third gen. The piggyback needs tapped into the tach, maf, o2 sensor, and power. I was able to figure out all of the 2nd gen wiring but I can’t find a pinout for a 2012 ecu anywhere.

The previous owner also said that power enterprise told him to leave out the wire for the o2 to get rid of the check engine light that he was having. This seems odd to me. The controller tricks the maf and has a vacuum line hooked up to see how much boost it’s making but it doesn’t seem right to not have the controller hooked up to the o2.

I’m going to keep looking for a 2012 ecu pinout and try to get in touch with power enterprise tomorrow. I don’t feel right without the controller knowing if it’s adding the right amount of fuel.
I have a pinout somewhere
DarkShadowFox is offline   Reply With Quote
Old 06-11-2018, 12:44 PM   #57
Dliverance
 
Drives: 2012 Black sand pearl <3
Join Date: Feb 2018
Location: Elma Washington
Posts: 136
Quote:
Originally Posted by DarkShadowFox View Post
I have a pinout somewhere
You should find it and share the wealth
Dliverance is offline   Reply With Quote
Old 06-11-2018, 01:19 PM   #58
Dliverance
 
Drives: 2012 Black sand pearl <3
Join Date: Feb 2018
Location: Elma Washington
Posts: 136
I got sent an email off to power enterprise. They have a kit specific to the 3rd gen and it uses the same controller so that’s good. I asked them for the installation manual for my year. Hopefully they get that sent off soon. I really want to get the kit installed before the next event.
Dliverance is offline   Reply With Quote
Old 06-11-2018, 01:31 PM   #59
DarkShadowFox
Banned
 
Drives: 2015 Yaris LE 3door 1F7
Join Date: Feb 2017
Location: Massachusetts
Posts: 963
Quote:
Originally Posted by Dliverance View Post
You should find it and share the wealth
what does a pinout diagram look like i have a shit ton of options on my GSIC:


DarkShadowFox is offline   Reply With Quote
Old 06-11-2018, 01:43 PM   #60
DarkShadowFox
Banned
 
Drives: 2015 Yaris LE 3door 1F7
Join Date: Feb 2017
Location: Massachusetts
Posts: 963
okay i have two diagrams for 'ECM' let me know if these help:



DarkShadowFox is offline   Reply With Quote
Old 06-11-2018, 02:31 PM   #61
Dliverance
 
Drives: 2012 Black sand pearl <3
Join Date: Feb 2018
Location: Elma Washington
Posts: 136
I need this one ^ but for the 2012 connector with descriptions
Dliverance is offline   Reply With Quote
Old 06-11-2018, 03:31 PM   #62
DarkShadowFox
Banned
 
Drives: 2015 Yaris LE 3door 1F7
Join Date: Feb 2017
Location: Massachusetts
Posts: 963
Quote:
Originally Posted by Dliverance View Post
I need this one ^ but for the 2012 connector with descriptions
it is for the 2012. the 2012 is the 2011 in europe. and so on and so forth.
DarkShadowFox is offline   Reply With Quote
Old 06-11-2018, 04:54 PM   #63
Dliverance
 
Drives: 2012 Black sand pearl <3
Join Date: Feb 2018
Location: Elma Washington
Posts: 136


Looks a little different to me
Dliverance is offline   Reply With Quote
Old 06-11-2018, 05:36 PM   #64
DarkShadowFox
Banned
 
Drives: 2015 Yaris LE 3door 1F7
Join Date: Feb 2017
Location: Massachusetts
Posts: 963
Quote:
Originally Posted by Dliverance View Post


Looks a little different to me
i dunno dude your gonna have to wire trace your harness or find a more updated version.
DarkShadowFox is offline   Reply With Quote
Old 06-14-2018, 08:50 PM   #65
Dliverance
 
Drives: 2012 Black sand pearl <3
Join Date: Feb 2018
Location: Elma Washington
Posts: 136
Thank you for the effort though
Dliverance is offline   Reply With Quote
Old 06-15-2018, 03:31 AM   #66
Dliverance
 
Drives: 2012 Black sand pearl <3
Join Date: Feb 2018
Location: Elma Washington
Posts: 136

Score
Dliverance is offline   Reply With Quote
Old 06-19-2018, 01:40 AM   #67
Dliverance
 
Drives: 2012 Black sand pearl <3
Join Date: Feb 2018
Location: Elma Washington
Posts: 136
It’s been a long few days of dealing with this piggyback. I finally got an email back from power enterprise and they were super helpful. They sent me the wiring diagram for the ncp131 but unfortunately, they use a newer controller. The new controller from them would have cost me about $1200 shipped but while I was looking, I found the mapecu3 looks remarkably similar to the power enterprise pmap controller. The connectors and wire colors are all the same. After learning this, I started looking for mapecu controllers. The mapecu3 (newest model with features I don’t need) costs about $650 new but I was able to find the mapecu gen 1 for $200. The only problem now is that the map ecu 1 has one 18 pin connector and the 3 has an 18 and a 16. Right now I’m waiting for an email back from mapecu to get a copy of the diagram for the gen 3. Once I get that, the only thing I need is the map for the ncp131 from power enterprise.

It sounds like a complicated cluster f but it’s really not that bad. Best part is that I’ll be able to sell the 07-11 piggyback to recoup some funds for the mapecu purchase.
Dliverance is offline   Reply With Quote
Old 06-19-2018, 04:51 AM   #68
Dliverance
 
Drives: 2012 Black sand pearl <3
Join Date: Feb 2018
Location: Elma Washington
Posts: 136
I was able to find the pinout for the newer mapecu. I need the 2 or 3 to run the supercharger. The gen 1 doesn’t have ignition timing capabilities. I was able to find the pinout and identify the wires on the ecu side too. The good news is that power enterprise got ahold of me and let me know that it’s the same programmer and their map will work. I’m just trying to source a gen 2 now. I’m pretty stoked.
Dliverance is offline   Reply With Quote
Old 06-19-2018, 04:45 PM   #69
Captain Yaris
 
Captain Yaris's Avatar
 
Drives: 2016 Yaris 3 Dr Super White
Join Date: Mar 2016
Location: SoFloYo
Posts: 259
Quote:
Originally Posted by Dliverance View Post

Score
Awesome score! I saw the box shape and then I saw the part number. I thought, hey! I know what that is! I am installing mine in the next few days. 👍🏽
Captain Yaris is offline   Reply With Quote
Old 06-19-2018, 07:53 PM   #70
Dliverance
 
Drives: 2012 Black sand pearl <3
Join Date: Feb 2018
Location: Elma Washington
Posts: 136
Haha awesome. I’ve been procrastinating on installing mine.

Here’s the mapecu2 I found. $300 on Facebook.


Last edited by Dliverance; 06-19-2018 at 10:58 PM.
Dliverance is offline   Reply With Quote
Old 06-20-2018, 09:02 PM   #71
Dliverance
 
Drives: 2012 Black sand pearl <3
Join Date: Feb 2018
Location: Elma Washington
Posts: 136
Woohoo!!! Just paid for the map. I can start the installation when I get back from my trip to Florida.
Dliverance is offline   Reply With Quote
Old 05-23-2019, 08:17 AM   #72
iam_elmanny
 
Drives: 14 Yaris L
Join Date: Nov 2018
Location: Florida
Posts: 25
Quote:
Originally Posted by Dliverance View Post
Got my Megan acleback on today. I was expecting more sound but I can hardly hear it over the loud federals. Did pretty good at today’s event though. I’m hoping the sway bar will be here this week so I can have it installed for the next event.



will that exhaust fit a 2014 2 door hatch?
iam_elmanny is offline   Reply With Quote
Reply

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -4. The time now is 07:34 PM.




YarisWorld
Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2024, vBulletin Solutions Inc.