Toyota Yaris Forums - Ultimate Yaris Enthusiast Site
 

 


 
Go Back   Toyota Yaris Forums - Ultimate Yaris Enthusiast Site > Technical Forums > Forced Induction Forum
  The Tire Rack

Reply
 
Thread Tools Display Modes
Old 08-31-2017, 07:50 AM   #19
ncp13
 
ncp13's Avatar
 
Drives: 01 Yaris TS
Join Date: Jan 2017
Location: Athens Greece
Posts: 92
The install is complete.!

I used a Gates 6PK1678 belt that fits corolla 120 3zz and made a 4 rib belt. 12e. It comes also in 6PK1670 which I think will be my next try because I get a squeal at 5500rpm

Today I got a P0171 .

I checked for vacuum leaks.. nothing..
Long term fuel trim 30 at idle 0 coast -7 when I floor it..

My injectors are 23250-21020 stock 1nz I assume. My fuel pressure was checked before the instalation and the injetor o-rings replaced during the install..
ncp13 is offline   Reply With Quote
Old 09-04-2017, 01:20 PM   #20
ncp13
 
ncp13's Avatar
 
Drives: 01 Yaris TS
Join Date: Jan 2017
Location: Athens Greece
Posts: 92
Small update..

Vacuum leaks and more vacuum leaks.

The previous owner had thick permanite compressor gaskets made and i made copies with the same material... Bad move .. The material is too thick .

Made some new ones myself with gasket paper and will install tomorrow. ..
Should i cut off that damn aluminum c section on the valve cover that protects the fuel rail? Its in the way
ncp13 is offline   Reply With Quote
Old 09-06-2017, 04:15 AM   #21
ncp13
 
ncp13's Avatar
 
Drives: 01 Yaris TS
Join Date: Jan 2017
Location: Athens Greece
Posts: 92
Vacuum leaks fixed with Toyota Black seal packing and no gaskets..

I tried the paper ones I made without luck.. and then the seal packing came to the rescue .. I am up to 5 times R/R the charger unit.. Dam..
I am getting good at it.

Now of to find a good belt as the Gates 6PK1678 at full tension squeals.
I will try their 1670 or maybe source a 4PK1675 if I am lucky.
ncp13 is offline   Reply With Quote
Old 09-11-2017, 02:58 AM   #22
ncp13
 
ncp13's Avatar
 
Drives: 01 Yaris TS
Join Date: Jan 2017
Location: Athens Greece
Posts: 92
Update on the belt slip.

I tighten about a turn at a time until I have a minor squeal at about 6100 which is fine for me.. I will leave it at that .

The 6PK1670 at the current adjustment leaves aboout 15mm on the bottom of the tensioner bolt so there is still some adjustment left. I will search for a 1665 lenght belt and see :)

The power is pretty linear with a flat spot around 5200 rpm and then a hard pull till redline. I have to datalog a few runs and attach a boost gauge to see whats going on .

Also there is a hessitation if the kompressor gets activated with the engine cold . I have to datalog that too..

I am still with the stock spark plugs, I will try the 20 range and see.
ncp13 is offline   Reply With Quote
Old 09-13-2017, 04:22 AM   #23
ncp13
 
ncp13's Avatar
 
Drives: 01 Yaris TS
Join Date: Jan 2017
Location: Athens Greece
Posts: 92
Did the colder spark plugs.

I reset the ECU and the car felt more responsive.. hmm

I installed the blitz timer boost gauge contraption that came with the kit and I verified 0.52 hkPa which is around 7.2 psi.. cool.. I hate the looks of that dam little thing and its coming off.. I did not care for the timer either..

Any tips or advice ?
ncp13 is offline   Reply With Quote
Old 09-13-2017, 10:25 AM   #24
MugenRep
iQ innovator & researcher
 
MugenRep's Avatar
 
Drives: 2012 iQ
Join Date: Mar 2016
Location: Central Pennsylvania
Posts: 199
Love all the updates! Keep them up!
MugenRep is offline   Reply With Quote
Old 09-14-2017, 06:37 AM   #25
ncp13
 
ncp13's Avatar
 
Drives: 01 Yaris TS
Join Date: Jan 2017
Location: Athens Greece
Posts: 92
Update

Yesterday taking off from low rpm and getting on boost I heard a little pinging..
It was 36C outside temp and just got off the highway. Regular 95 octane fuel was used..

Should I try the 22 heat range spark plugs?
ncp13 is offline   Reply With Quote
Old 11-08-2017, 06:49 AM   #26
ncp13
 
ncp13's Avatar
 
Drives: 01 Yaris TS
Join Date: Jan 2017
Location: Athens Greece
Posts: 92
Boost weather finally here

Finally we got turbo weather here in Greece.

8C at night 15C during the day..

The car is super responsive.. I cant convince myself to do the blue emanage yet.

It does feel restricted at high rpms. (stock intake, exhaust etc..) and then it sqeels at about 6k rpm..

I want to find 6 rib pulleys for my Ac/wp/crank/Blitz compressor to do away with the sqeal . Does anybody know of any models that I can get the from? ex Camry , avalon etc?
ncp13 is offline   Reply With Quote
Old 11-08-2017, 10:18 AM   #27
CrankyOldMan
2ZR swap. DO IT! Ask how!
 
CrankyOldMan's Avatar
 
Drives: 09 Meteoric Metallic HB
Join Date: Feb 2011
Location: West Michigan
Posts: 2,333
The problem you will have is finding a pulley for the compressor. It uses a spline connection instead of the more common taper and key style. I was never able to find one that would fit, so you might have to make something custom.

It's definitely restricted by the stock exhaust. Even with a CAI, 1ZZ throttle body and custom intake plumbing mine would die off above ~5500. Belt squeal is only controllable by tightening the accessory belt, but that puts extra strain on your bearings/pulleys on the accessory loop and can shear off the bolt on the far side of the intake plenum. Yes, I broke pretty much all of those things on mine.
CrankyOldMan is offline   Reply With Quote
Old 11-18-2017, 05:18 AM   #28
ncp13
 
ncp13's Avatar
 
Drives: 01 Yaris TS
Join Date: Jan 2017
Location: Athens Greece
Posts: 92
For the compressor inguess i have to find another ac/clutch pulley for 6 rib..

I will try to free up cat and the rest of the system but with somthing quiet .. I hate unecessary noise polution .. I guess i am getting old and cranky too

ncp13 is offline   Reply With Quote
Old 11-18-2017, 02:19 PM   #29
thebarber
daily driver
 
thebarber's Avatar
 
Drives: the #wrecho
Join Date: Jun 2006
Location: Grand Rapids, MI
Posts: 5,877
Use 1zzfe injectors if you aren't already
__________________
thebarber is offline   Reply With Quote
Old 12-04-2017, 06:41 AM   #30
Gorilla
 
Gorilla's Avatar
 
Drives: Vitz & Supra
Join Date: Jan 2011
Location: Sydney, Australia
Posts: 41
Good updates mate. Mines still going well after a couple of years but i really want more...I need more power lol...Can not find a pulley to suit :(
Gorilla is offline   Reply With Quote
Old 01-04-2018, 02:03 PM   #31
ncp13
 
ncp13's Avatar
 
Drives: 01 Yaris TS
Join Date: Jan 2017
Location: Athens Greece
Posts: 92
Happy new Year yall !

I decided to free up the exhaust flow one piece at a time. Since an internal combustion engine is an air pump and i stuffed about 30% more in to it i should do somthing with the catalytic converter. I will make a pipe with a universal cat for a 2.0 vehicle and i will see how it goes :) .

The belt squeal is anoying and thats next on the agenda.

Btw does the s/c pulley comes apart easy? Anyone with pictures of it apart?

ncp13 is offline   Reply With Quote
Reply

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump

Similar Threads
Thread Thread Starter Forum Replies Last Post
List of Boosted Yarisworld Members whooppee777 Forced Induction Forum 262 11-23-2022 05:49 AM
2008 vitzRs clone+fixed pulley blitz... blacksandiegovitz Forced Induction Forum 5 12-05-2010 01:26 PM
Blitz throttle controller 808_Yaris Performance Modifications 43 10-22-2009 04:36 AM
BLITZ HAS CLOSED????? ROCKLAND TOYOTA General Yaris / Vitz Discussion 12 08-13-2009 05:35 AM
GI: OFFICIAL BLITZ YARIS laszlo Cars for Sale by private party 11 11-25-2008 05:05 AM


All times are GMT -4. The time now is 02:30 PM.




YarisWorld
Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2024, vBulletin Solutions Inc.