Blitz SuperCharger Install - Page 4 - Toyota Yaris Forums

CTScott · 03-08-2009, 09:11 PM

Quote:

Originally Posted by PETERPOOP

Having trouble locating A21-55# on the 60 pin harness for the ECU. The wiring diagram doesn't list it. What the..

It's the red wire (VPA) from the accelerator position sensor to the ECU:

ECM Conn.jpg

PETERPOOP · 03-08-2009, 09:19 PM

Thanks for that thing! The part that says A21 on the top is in japanese on my instructions. And it doesn't have all the numbers!

nisyota · 03-08-2009, 09:22 PM

so... is it installed yet? :D

LtNoogie · 03-08-2009, 09:26 PM

Peter. Close your eyes and just use the Force.

j/k

I don't think I read much of the instructions during this part of the installation. I followed the wiring diagram and counted pins from the edge of ECU connectors.

This is where you have to be very careful that you are oriented correctly to the diagram. My brother and I independently counted out and called out what color wire should be worked on next. We only proceeded if we argreed upon the color of the harness wire.

PETERPOOP · 03-08-2009, 10:06 PM

soldering and shrink wrapping is taking forever...

808_Yaris · 03-08-2009, 10:09 PM

Quote:

Originally Posted by PETERPOOP

soldering and shrink wrapping is taking forever...

so you'll be finished today peter?

AlexNet0 · 03-08-2009, 10:14 PM

I hope so, Im still awake and need something to follow, lol

808_Yaris · 03-08-2009, 10:35 PM

lol peter did you need to use a magnet again?

PETERPOOP · 03-08-2009, 10:37 PM

hah. 808_yaris was a help with his magnet yesterday. Some bolts fell down the engine bay and we used that thing to get them out! Hoping to be done today! Have one more wire to solder!!! Still haven't put the controller anywhere yet. Might just let it hang for now so we can test drive it. Once the wire is done soldering, need to hook up the battery and start her up... I pray for no CELs.

LtNoogie · 03-08-2009, 10:43 PM

I remember using the magnet too. Also had to lay on the floor and reach around in the lower shroud for tools that I dropped in the engine bay.

KCALB SIRAY · 03-08-2009, 11:05 PM

Quote:

Originally Posted by PETERPOOP

soldering and shrink wrapping is taking forever...

But it is sooo worth it in the end with a clean factory look and better protection. Can't wait to see it

Quote:

Originally Posted by LtNoogie

I remember using the magnet too. Also had to lay on the floor and reach around in the lower shroud for tools that I dropped in the engine bay.

huh huh, Long said "reach around"

anonymous user · 03-08-2009, 11:25 PM

Quote:

Originally Posted by PETERPOOP

Can't wait to put this in.

I put it in every tank. It feels great when you first add it. I think the car adjusts to it though.

So how was the install, and did you have a mechanic help you, or someone just lent you a hand?

PETERPOOP · 03-09-2009, 12:16 AM

IT'S ALIVE!!! No fuel leaks. Everything is running GREAT! No CELS! Just the smell of burnt rubber in the rain!!! MUAHAHAHA! So much torque!!! I love it. Can't wait to run my new exhaust setup and free up more HP in the higher RPMS!

Thanks to noogie and KK for the tips! Noogie's thread was very helpful!

VIDEOS COMING TONIGHT!!!

kou · 03-09-2009, 12:20 AM

congratulations

PETERPOOP · 03-09-2009, 12:35 AM

Quote:

Originally Posted by anonymous user

I put it in every tank. It feels great when you first add it. I think the car adjusts to it though.

So how was the install, and did you have a mechanic help you, or someone just lent you a hand?

No mechanic. My dad helped me. Definately would not want to do it again. I will probably only be using half a bottle or a third of the boost octane when i fill up!

PETERPOOP · 03-09-2009, 12:47 AM

I ain't no camell, doc, noogie, KK, whoope, etc.. Here's my video of me driving the car seconds after finishing install! Yah baby! It was raining the entire time we were installing it. The roads were wet and provided no traction when I wanted to open it up. I'll still put up the video. Once the weather dries up this week (hopefully), I'll get some 0-60 videos (etc.) without a passenger riding with me!

http://www.youtube.com/watch?v=SFT8SE1kSHM

The tires were spinning the entire time in 1st during the 1st clip of me driving it. I didn't even take it to 6000rpms because it got no traction! MORE VIDEOS TO COME THIS WEEK!

LtNoogie · 03-09-2009, 01:25 AM

Welcome to the club.

How much clearance do you have between your belt and air conditioner block thingy? It was hard to tell from your video.

PETERPOOP · 03-09-2009, 01:29 AM

Thanks. I got a few inches. I didn't even tie it to the side or whatever. Just yanked it out of the way. I'll get better pics and videos tomorrow! Gotta install the iridium spark plugs still.

03-08-2009, 09:26 PM	#58
LtNoogie View User's Garage Drives: '08 Bayou Blue LB AT Join Date: Oct 2008 Location: West Hills, CA Posts: 2,517	Peter. Close your eyes and just use the Force. j/k I don't think I read much of the instructions during this part of the installation. I followed the wiring diagram and counted pins from the edge of ECU connectors. This is where you have to be very careful that you are oriented correctly to the diagram. My brother and I independently counted out and called out what color wire should be worked on next. We only proceeded if we argreed upon the color of the harness wire. __________________ aFe Intake \| Blitz Supercharger \| Megan Header \| TRD Exhaust \| NST Pulley Set TRD Shocks/Struts \| Tanabe NF210 Springs \| TRD Sway Bar \| Motegi TRAKLITE wheels \| Kuhmo Ecsta XS R1 Concepts slotted rotors \| Carbotech 1521 brake pads \| stainless steel brake lines \| Seibon vented carbon fiber hood

03-08-2009, 10:14 PM	#61
AlexNet0 View User's Garage Drives: '07 Yaris 3dr Join Date: Nov 2008 Location: Rockland, ME Posts: 1,638	I hope so, Im still awake and need something to follow, lol __________________ ---------- MI-YW ----------

03-08-2009, 10:43 PM	#64
LtNoogie View User's Garage Drives: '08 Bayou Blue LB AT Join Date: Oct 2008 Location: West Hills, CA Posts: 2,517	I remember using the magnet too. Also had to lay on the floor and reach around in the lower shroud for tools that I dropped in the engine bay. __________________ aFe Intake \| Blitz Supercharger \| Megan Header \| TRD Exhaust \| NST Pulley Set TRD Shocks/Struts \| Tanabe NF210 Springs \| TRD Sway Bar \| Motegi TRAKLITE wheels \| Kuhmo Ecsta XS R1 Concepts slotted rotors \| Carbotech 1521 brake pads \| stainless steel brake lines \| Seibon vented carbon fiber hood

03-09-2009, 01:25 AM	#71
LtNoogie View User's Garage Drives: '08 Bayou Blue LB AT Join Date: Oct 2008 Location: West Hills, CA Posts: 2,517	Welcome to the club. How much clearance do you have between your belt and air conditioner block thingy? It was hard to tell from your video. __________________ aFe Intake \| Blitz Supercharger \| Megan Header \| TRD Exhaust \| NST Pulley Set TRD Shocks/Struts \| Tanabe NF210 Springs \| TRD Sway Bar \| Motegi TRAKLITE wheels \| Kuhmo Ecsta XS R1 Concepts slotted rotors \| Carbotech 1521 brake pads \| stainless steel brake lines \| Seibon vented carbon fiber hood

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
List of Boosted Yarisworld Members	whooppee777	Forced Induction Forum	262	11-23-2022 05:49 AM
BLITZ supercharger kits IN STOCK	cali yaris	Micro Image	34	06-02-2012 10:31 AM
anyone with Blitz supercharger?	yrsdrgn	Performance Modifications	52	08-24-2010 07:57 AM
Blitz Supercharger vendors	sdyaris	Forced Induction Forum	32	09-18-2009 12:28 AM
blitz supercharger!!!	djgab101	Australia	4	11-20-2008 05:06 AM

03-08-2009, 09:19 PM	#56
PETERPOOP View User's Garage Drives: 08 white liftback Join Date: Oct 2008 Location: Oahu Posts: 3,674	Thanks for that thing! The part that says A21 on the top is in japanese on my instructions. And it doesn't have all the numbers!

03-08-2009, 09:22 PM	#57
nisyota Drives: 2007 Toyota Yaris Sedan Join Date: Feb 2009 Location: Orlando, USA Posts: 73	so... is it installed yet? :D

03-08-2009, 10:06 PM	#59
PETERPOOP View User's Garage Drives: 08 white liftback Join Date: Oct 2008 Location: Oahu Posts: 3,674	soldering and shrink wrapping is taking forever...

03-08-2009, 10:35 PM	#62
808_Yaris Where is Oahu? View User's Garage Drives: 5-door meteorite metallic Join Date: Dec 2008 Location: HI Posts: 1,346	lol peter did you need to use a magnet again?

03-08-2009, 10:37 PM	#63
PETERPOOP View User's Garage Drives: 08 white liftback Join Date: Oct 2008 Location: Oahu Posts: 3,674	hah. 808_yaris was a help with his magnet yesterday. Some bolts fell down the engine bay and we used that thing to get them out! Hoping to be done today! Have one more wire to solder!!! Still haven't put the controller anywhere yet. Might just let it hang for now so we can test drive it. Once the wire is done soldering, need to hook up the battery and start her up... I pray for no CELs.

03-09-2009, 12:16 AM	#67
PETERPOOP View User's Garage Drives: 08 white liftback Join Date: Oct 2008 Location: Oahu Posts: 3,674	IT'S ALIVE!!! No fuel leaks. Everything is running GREAT! No CELS! Just the smell of burnt rubber in the rain!!! MUAHAHAHA! So much torque!!! I love it. Can't wait to run my new exhaust setup and free up more HP in the higher RPMS! Thanks to noogie and KK for the tips! Noogie's thread was very helpful! VIDEOS COMING TONIGHT!!!

03-09-2009, 12:20 AM	#68
kou View User's Garage Drives: 08 lb Join Date: Aug 2007 Location: nj Posts: 935	congratulations

03-09-2009, 12:47 AM	#70
PETERPOOP View User's Garage Drives: 08 white liftback Join Date: Oct 2008 Location: Oahu Posts: 3,674	I ain't no camell, doc, noogie, KK, whoope, etc.. Here's my video of me driving the car seconds after finishing install! Yah baby! It was raining the entire time we were installing it. The roads were wet and provided no traction when I wanted to open it up. I'll still put up the video. Once the weather dries up this week (hopefully), I'll get some 0-60 videos (etc.) without a passenger riding with me! http://www.youtube.com/watch?v=SFT8SE1kSHM The tires were spinning the entire time in 1st during the 1st clip of me driving it. I didn't even take it to 6000rpms because it got no traction! MORE VIDEOS TO COME THIS WEEK!

03-09-2009, 01:29 AM	#72
PETERPOOP View User's Garage Drives: 08 white liftback Join Date: Oct 2008 Location: Oahu Posts: 3,674	Thanks. I got a few inches. I didn't even tie it to the side or whatever. Just yanked it out of the way. I'll get better pics and videos tomorrow! Gotta install the iridium spark plugs still.