DIY Cruise Control FAQ (2006-2010 Yaris)

[CTScott]

Originally Posted by hockysa

Hi is there any information anywhere on these installs?

I've acquired a second hand AP800 and want to install it on my Yaris and have figured out the wiring except for the accelerator pedal.

Like I asked on your other thread - What year is your Yaris, as that makes a difference in the wiring?

[hockysa]

Originally Posted by CTScott

Like I asked on your other thread - What year is your Yaris, as that makes a difference in the wiring?

oh sorry didn't see a reply

it's a 2007 Yaris

[CTScott]

Originally Posted by hockysa

oh sorry didn't see a reply

it's a 2007 Yaris

OK. The accelerator pedal has a 6 pin connector.

1 - White: VCP2 (Sensor 2 power)
2 - Brown: EPA2 (Sensor 2 ground)
3 - Light blue: VPA2 (Sensor 2 output)
4 - Black: VCPA (Sensor 1 power)
5 - Green: EPA (Sensor 1 ground)
6 - Red: VPA (Sensor 1 output)


I haven't seen the install manual for the AP800 for the Yaris, but looking at the pinout of the AP800 it has a high and low throttle position sensor connections.

On the Yaris the VPA signal would be the low one (2.6 to 4.5 V at full throttle) and VPA2 would be the high one (3.4 to 5.0 V at full throttle).

[hockysa]

Awesome that's perfect
thanks!

you don't also happen to have the same thing for a 2006 Corolla do you?
It's also a 6pin plug but different configuration

*edit*
also where did you find it?
because I've been searching for hours and got nothing

*edit edit*
just googled corolla VCP2 and found it :S

Originally Posted by CTScott

OK. The accelerator pedal has a 6 pin connector.

1 - White: VCP2 (Sensor 2 power)
2 - Brown: EPA2 (Sensor 2 ground)
3 - Light blue: VPA2 (Sensor 2 output)
4 - Black: VCPA (Sensor 1 power)
5 - Green: EPA (Sensor 1 ground)
6 - Red: VPA (Sensor 1 output)


I haven't seen the install manual for the AP800 for the Yaris, but looking at the pinout of the AP800 it has a high and low throttle position sensor connections.

On the Yaris the VPA signal would be the low one (2.6 to 4.5 V at full throttle) and VPA2 would be the high one (3.4 to 5.0 V at full throttle).

[CTScott]

Originally Posted by hockysa

Awesome that's perfect
thanks!

you don't also happen to have the same thing for a 2006 Corolla do you?
It's also a 6pin plug but different configuration

*edit*
also where did you find it?
because I've been searching for hours and got nothing

*edit edit*
just googled corolla VCP2 and found it :S

I don't have the info for the Corolla, but the pinout order is likely the same with just the wire colors being different. You can verify that by measuring the voltage on the pins where the "power" pins should have 5 volts on them and the grounds zero.

I found a manual for the aftermarket cruise online, but it was not for a Yaris.

[hockysa]

Originally Posted by CTScott

I don't have the info for the Corolla, but the pinout order is likely the same with just the wire colors being different. You can verify that by measuring the voltage on the pins where the "power" pins should have 5 volts on them and the grounds zero.

I found a manual for the aftermarket cruise online, but it was not for a Yaris.

Yeah I thought the same too but the order is different

yeah? could you link it to me anyway please?

[CTScott]

Originally Posted by hockysa

Yeah I thought the same too but the order is different

yeah? could you link it to me anyway please?

http://nicolas.bct.free.fr/Regulateu...rateur_HDi.pdf

I ran into the diagram for the 05 Corolla and it shows:

1. Yellow - EPA2
2. White - VPA2
3. Yellow - EPA
4. Black - VCP2
5. Green - VPA
6. Black - VCPA