|
10-12-2015, 03:44 PM | #1 |
Drives: 1987 Silverado Join Date: Jan 2010
Location: Texas
Posts: 314
|
Lining up the head lights '09
|
10-13-2015, 09:53 PM | #2 |
Drives: 1987 Silverado Join Date: Jan 2010
Location: Texas
Posts: 314
|
Anyone? Is anybody still out there?
|
10-13-2015, 10:29 PM | #3 |
ULTIMATE
Drives: 09 5dr LB, 2x 08 3dr LB Join Date: Oct 2008
Location: USA, CT
Posts: 13,460
|
For the sedan the adjuster is inboard and below of the headlight bulb. In your first picture it is the device just below the grey connector.
__________________
|
10-13-2015, 10:43 PM | #4 |
Join Date: Feb 2010
Posts: 603
|
I prefer this...https://www.youtube.com/watch?v=NP0mQeLWCCo Patients sometimes on this forum is needed...but you will get a response....usually, as in this case, from the master...CTScott. |
10-22-2015, 03:25 AM | #5 | |
Drives: 1987 Silverado Join Date: Jan 2010
Location: Texas
Posts: 314
|
Quote:
From your reply it looks like I could get to it easier, if I unplug that plug in the first pic. Would you say that the adjustment screw, is fairly easy to access? |
|
10-22-2015, 05:58 AM | #6 | |
ULTIMATE
Drives: 09 5dr LB, 2x 08 3dr LB Join Date: Oct 2008
Location: USA, CT
Posts: 13,460
|
Quote:
__________________
|
|
10-22-2015, 11:36 AM | #7 |
It's the illusion you see
Drives: 07 Yaris Sedan Aero Join Date: Oct 2006
Location: Brossard, QC
Posts: 3,888
|
Hm? Put a Philips head screw driver in the hole. That's the adjuster for height. There are no horizontal adjustments AFAIK. If you look down there, you will see it, it can also be adjusted with a hex wrench.
uploadfromtaptalk1445528209866.jpg Sent from my A0001 using Tapatalk |
10-22-2015, 07:34 PM | #8 | |
ULTIMATE
Drives: 09 5dr LB, 2x 08 3dr LB Join Date: Oct 2008
Location: USA, CT
Posts: 13,460
|
Quote:
__________________
|
|
10-28-2015, 12:15 AM | #9 | |
Drives: 1987 Silverado Join Date: Jan 2010
Location: Texas
Posts: 314
|
Quote:
And with it i was able to adjust the lights. Thanks again |
|
10-30-2015, 07:16 AM | #10 | |
Drives: 1987 Silverado Join Date: Jan 2010
Location: Texas
Posts: 314
|
Quote:
That said, I noticed your reply says something totally different than his. You say its that one with the washer looking head, he says it those others. For me, the ones he said turned out to be the correct one. So is the other one for something else? |
|
10-30-2015, 02:15 PM | #11 |
やりすぎだ~
|
Here. IllusionX circled the same thing except that the part he circled, the adjusting screw, isn't visible, it's behind that plastic. So it looks like he circled those plastic tabs.
|
10-30-2015, 10:52 PM | #12 |
Drives: 08 Yaris sedan auto / Fit auto Join Date: Oct 2009
Location: northeast
Posts: 2,897
|
I would use the horizontal mortar lines of a brick wall to get headlight height the same . Park car on level ground about 5 feet away from side of a brick wall at night and make adjustments .
|
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
3rd Gen Vitz RS (and G's) Tail Lights: Part Numbers, Ordering, and Installation | keiri | Third Gen Yaris General Discussion | 26 | 09-04-2020 12:01 AM |
LED License plate lights for Yaris Sedan | YarisSedan | DIY / Maintenance / Service | 6 | 04-09-2013 04:05 PM |
Instrument Panel goes out if I turn on my lights | ceceb | DIY / Maintenance / Service | 9 | 07-08-2010 05:56 PM |
Solar powered High Bright LED lights replacing the fog lights | alan1828 | Canada | 10 | 05-14-2010 12:34 AM |
Changing LED's In Projector Head Lights | whooppee777 | Cosmetic Modifications (Exterior/Interior) | 16 | 03-01-2009 02:07 PM |