Toyota Yaris Forums - Ultimate Yaris Enthusiast Site
 

 


 
Go Back   Toyota Yaris Forums - Ultimate Yaris Enthusiast Site > Technical Forums > DIY / Maintenance / Service
  The Tire Rack

Reply
 
Thread Tools Display Modes
Old 04-29-2009, 11:35 PM   #1
CTScott
ULTIMATE
 
CTScott's Avatar
 
Drives: 09 5dr LB, 2x 08 3dr LB
Join Date: Oct 2008
Location: USA, CT
Posts: 13,460
DIY - 2009 Cruise Control for $10, without pulling the steering wheel and airbag

This DIY came from the following thread, discussing the possibility of adding cruise control by simply adding the OEM cruise control stalk:

http://www.yarisworld.com/forums/showthread.php?t=16188

2009 Yaris are prewired for cruise control. To enable this functionality one may add the OEM stalk, but doing so requires the removal of the steering wheel and airbag. Also, the dealer price for the OEM stalk is ~$125.

After looking at the cruise control section of the service manual, I realized that the stalk's functionality (On/Off, -(Set), +(Resume), and Cancel) could be recreated using four switches and three resistors. Alternately, basic cruise control functionality (On/Off and Set) can be provided using two switches and one (or two) resistors.

Currently, it is believed that this will also work for 07-08 Yaris, but a wire will have to be connected to connector A21 of the ECM or Connector AD4 (which is located above the top of the fuse panel, just under the dash).

Note: For Manual Transmission equipped Yaris, the "Cruise Control Clutch Switch" is needed as well. This is a second clutch switch (there's already one called the "Clutch Start Switch"). The "Cruise Control Clutch Switch" connects to connector A29. Its part number is: 88280-14030 and it lists for ~$18.



Materials required:
4 - Switches (SPST, Normally Open, Momentary) (Digikey part number EG1900-ND, $2.44 each)
1 - 240 Ohm Resistor (Digikey part number 240QBK-ND, $.06)
1 - 390 Ohm Resistor (Digikey part number 390QBK-ND, $.06)
1 - 910 Ohm Resistor (Digikey part number 910QBK-ND, $.06)
~4ft - Wire, 20-24 AWG, 2 colors

I purchased the switches and resistors from Digikey (http://www.digikey.com/).





Procedure:

1. Make sure your car is pre-wired for cruise control:

Check the Combination Meter for the Crusie Control Lights:
Shining a flashlight to the right of the speedometer will make the two
cruise control icons visible if they are present. They will not illuminate,
but will look like the two below:



2. Remove the lower steering column cover:

Rotate the steering wheel all the way to either side, and remove the two screws:




Remove the screw by the steering wheel tilt lever:


Squeeze the lower steering column cover, by the seam between it and the upper, and gently pull down to remove it.


3. Identify the Cruise Control wires on Connector D3 (white connector at the base of the steering wheel next to the yellow connector): CCS (Blue wire in Pin 1) and ECC (Brown wire in Pin 3).




4. Chose a location to mount the switches. I mounted mine to the "push button start" cover to the right of the key switch. This location has a hole behind it approximately 1-5/8" in diameter. If using this location you must make sure that the back of the switches line up with this hole:

Switches mounted:


Hole behind cover:


Rear of cover (with two switches mounted):



5. Mount and wire switches:
Switches can be mounted in various positions, but wiring between them will be the same. Note that in the 4 switch example the leads of the 390 Ohm resistor are covered with heat shrink tubing to keep them from making contact with the other switch terminals.

4 Switch wiring:


2 Switch wiring (The two resistors could be replaced with a single 567-693 Ohm one) :



6. Connect wires from switch assembly to wires on connector D3.
Red wire from switches connects to blue wire of D3 Pin 1.
Black wire from switches connects to brown wire of D3 Pin 3.





7. Test Cruise Control functions:
On/Off function can be tested with the engine off and the ignition switch in the on position. Pressing the button once should illuminate the cruise control icon. Pressing it again should make the light go off:




The Set function requires that the car be moving at 25 MPH or greater. Pressing the Set switch at >25MPH will cause the SET light to illuminate.


Last edited by CTScott; 05-01-2009 at 09:20 PM. Reason: Add note about Cruise Control Clutch Switch for Manal Transmission
CTScott is offline   Reply With Quote
Old 04-29-2009, 11:44 PM   #2
KCALB SIRAY
それを吸ってください
 
KCALB SIRAY's Avatar
 
Drives: black sand lb
Join Date: Oct 2008
Location: Virginia
Posts: 8,894
very interesting, subscribed
KCALB SIRAY is offline   Reply With Quote
Old 04-30-2009, 12:08 AM   #3
MGargano
 
Drives: 2009 Yaris Hatchback
Join Date: Feb 2009
Location: NJ
Posts: 792
Quote:
Originally Posted by CTScott View Post
To enable this functionality one may add the OEM stalk, but doing so requires the removal of the steering wheel and airbag.
Is there any way to install the OEM stalk without removing the steering wheel & airbag?
MGargano is offline   Reply With Quote
Old 04-30-2009, 12:17 AM   #4
CTScott
ULTIMATE
 
CTScott's Avatar
 
Drives: 09 5dr LB, 2x 08 3dr LB
Join Date: Oct 2008
Location: USA, CT
Posts: 13,460
Quote:
Originally Posted by MGargano View Post
Is there any way to install the OEM stalk without removing the steering wheel & airbag?
No. It mounts under them, and the connector for the spiral cable is buried under there as well. Removing them is not a huge deal, it just requires some caution and care to not pop the airbag or break the clockspring.
CTScott is offline   Reply With Quote
Old 05-09-2009, 01:04 AM   #5
firemachine69
School'er of hard knocks
 
Drives: Silver Yaris 4dr. HB
Join Date: Oct 2008
Location: Sudbury, On
Posts: 556
Quote:
Originally Posted by CTScott View Post
No. It mounts under them, and the connector for the spiral cable is buried under there as well. Removing them is not a huge deal, it just requires some caution and care to not pop the airbag or break the clockspring.
Snapping the clockspring is a big concern. Very fragile piece. Airbag: not so much. Too many fail-safes built-in due to liability concerns.
firemachine69 is offline   Reply With Quote
Old 05-11-2009, 08:05 PM   #6
expo2
 
Drives: 2008 Yaris HB
Join Date: Dec 2008
Location: Gardiner, NY
Posts: 23
I'd like to do this mod to my '08 HB with no CC wiring or dash symbol. I'll run a wire from the ECM A21 connector @ position #40 then to the aftermarket on/off cruise switch.

My question is this: I'd like to have an LED light to indicate when the "cruise control" is "on." Where can I find a hot wire for the LED?
expo2 is offline   Reply With Quote
Old 05-11-2009, 09:04 PM   #7
CTScott
ULTIMATE
 
CTScott's Avatar
 
Drives: 09 5dr LB, 2x 08 3dr LB
Join Date: Oct 2008
Location: USA, CT
Posts: 13,460
Quote:
Originally Posted by expo2 View Post
I'd like to do this mod to my '08 HB with no CC wiring or dash symbol. I'll run a wire from the ECM A21 connector @ position #40 then to the aftermarket on/off cruise switch.

My question is this: I'd like to have an LED light to indicate when the "cruise control" is "on." Where can I find a hot wire for the LED?
The real cruise light is controlled by the combination meter, which gets the info about cruise mode over the CAN bus from the ECM, so there's no easy wire to connect the LED to.
CTScott is offline   Reply With Quote
Old 04-30-2009, 12:19 AM   #8
MGargano
 
Drives: 2009 Yaris Hatchback
Join Date: Feb 2009
Location: NJ
Posts: 792
Is there a DIY for removing the steering wheel & airbag?
MGargano is offline   Reply With Quote
Old 04-30-2009, 12:44 AM   #9
1NZYaris1
 
1NZYaris1's Avatar
 
Drives: Yaris
Join Date: Oct 2008
Location: New Zealand
Posts: 2,566
Quote:
Originally Posted by MGargano View Post
Is there a DIY for removing the steering wheel & airbag?
Here you go
Attached Files
File Type: pdf steering wheel removal (leather).pdf (995.7 KB, 783 views)
1NZYaris1 is offline   Reply With Quote
Old 04-30-2009, 12:45 AM   #10
Creeper
 
Creeper's Avatar
 
Drives: Silver 2DLB Yaris
Join Date: May 2007
Location: Georgia
Posts: 154
Send a message via AIM to Creeper
so you can do this with only 2 switches? on/off and set?
Creeper is offline   Reply With Quote
Old 04-30-2009, 07:27 AM   #11
CTScott
ULTIMATE
 
CTScott's Avatar
 
Drives: 09 5dr LB, 2x 08 3dr LB
Join Date: Oct 2008
Location: USA, CT
Posts: 13,460
Quote:
Originally Posted by Creeper View Post
so you can do this with only 2 switches? on/off and set?
Correct. That's what I did with mine. In any vehicle that I've had with cruise, I never find myself using the tap up/down or coast/resume, so I just went with two switches.
CTScott is offline   Reply With Quote
Old 05-06-2009, 06:33 AM   #12
stran
 
Drives: '07 Yaris 3D HB Auto
Join Date: Jul 2007
Location: Cal
Posts: 44
Quote:
Originally Posted by CTScott View Post
Correct. That's what I did with mine. In any vehicle that I've had with cruise, I never find myself using the tap up/down or coast/resume, so I just went with two switches.
If you push once to turn the cruise switch on. Then turn off the car, and turn the car back on again. Is cruise still on?
stran is offline   Reply With Quote
Old 05-06-2009, 07:37 AM   #13
CTScott
ULTIMATE
 
CTScott's Avatar
 
Drives: 09 5dr LB, 2x 08 3dr LB
Join Date: Oct 2008
Location: USA, CT
Posts: 13,460
Quote:
Originally Posted by stran View Post
If you push once to turn the cruise switch on. Then turn off the car, and turn the car back on again. Is cruise still on?
No. It resets with the ignition.
CTScott is offline   Reply With Quote
Old 05-06-2009, 10:33 AM   #14
mariann
 
Drives: yaris 2007
Join Date: Mar 2009
Location: israel
Posts: 39
it a wired question but...
i understand the on/off buton is for turning the cruise controll on and off
so whats the set button does? why i need two buttons? any one can explain me how to work with cruise controll?
mariann is offline   Reply With Quote
Old 03-20-2011, 11:47 PM   #15
saltwt
 
Drives: Yaris
Join Date: Feb 2011
Location: NJ
Posts: 4
Quote:
Originally Posted by CTScott View Post
Correct. That's what I did with mine. In any vehicle that I've had with cruise, I never find myself using the tap up/down or coast/resume, so I just went with two switches.
Thanks for the great DIY...Im going to try it this week.... 2010 Yaris...Found the Icons for the Set & Cruise on the top left section of the Cluster panel.
saltwt is offline   Reply With Quote
Old 03-22-2011, 04:11 PM   #16
saltwt
 
Drives: Yaris
Join Date: Feb 2011
Location: NJ
Posts: 4
Quote:
Originally Posted by saltwt View Post
Thanks for the great DIY...Im going to try it this week.... 2010 Yaris...Found the Icons for the Set & Cruise on the top left section of the Cluster panel.
This worked out great! Had the job done in a hour...cost was under ten dollars..radio shack came threw with the buttons and resistors.

Thanks...
Attached Images
File Type: jpg 2011-03-22 15.15.37-1.jpg (19.6 KB, 228 views)

Last edited by saltwt; 03-22-2011 at 04:12 PM. Reason: added picture..
saltwt is offline   Reply With Quote
Old 04-30-2009, 07:48 AM   #17
LtNoogie
 
LtNoogie's Avatar
 
Drives: '08 Bayou Blue LB AT
Join Date: Oct 2008
Location: West Hills, CA
Posts: 2,517
In instruction #7, the picture shows that the car thought this mod was pretty "cool" and said so!
__________________
aFe Intake | Blitz Supercharger | Megan Header | TRD Exhaust | NST Pulley Set
TRD Shocks/Struts | Tanabe NF210 Springs | TRD Sway Bar | Motegi TRAKLITE wheels | Kuhmo Ecsta XS
R1 Concepts slotted rotors | Carbotech 1521 brake pads | stainless steel brake lines | Seibon vented carbon fiber hood
LtNoogie is offline   Reply With Quote
Old 04-30-2009, 08:59 AM   #18
Tamago
Start another Oil Thread!
 
Tamago's Avatar
 
Drives: ZZW30
Join Date: Dec 2006
Location: South FL
Posts: 4,890
Send a message via AIM to Tamago Send a message via Yahoo to Tamago
http://www.allelectronics.com/make-a...-SWITCH/1.html

would be a nice switch, if it spring centers.. takes the place of two pushbuttons :)
__________________
Quote:
Originally Posted by xnamerxx
I hate people like you (xbgod) because your the reason I don't come to this board. You spout nonsense and lies and people who don't know any better hold you in high regards because they can't tell the wheat from the chaff.
you nailed it sir.
Tamago is offline   Reply With Quote
Reply

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump

Similar Threads
Thread Thread Starter Forum Replies Last Post
OEM foglight switch and leather wrap steering wheel 808yarisLB Cosmetic Modifications (Exterior/Interior) 8 03-11-2009 12:05 AM
SCION SPORT STEERING WHEEL, RED, XA AND XB, 03 TO 06 justoneyaris Items for Sale by private party 3 12-04-2008 06:30 PM
steering wheel setup aucorium Cosmetic Modifications (Exterior/Interior) 0 07-24-2007 01:05 AM
How do you take off steering wheel mrrock Cosmetic Modifications (Exterior/Interior) 3 12-05-2006 10:16 AM


All times are GMT -4. The time now is 04:56 AM.




YarisWorld
Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2024, vBulletin Solutions Inc.