 |
 |
|
|
05-17-2013, 01:53 AM
|
#1 |
 Drives: soarer Join Date: Feb 2011
Location: Beautiful British Columbia
Posts: 954
|
Noob turbo (zage) questions
Decided to start another thread as i have lots of really noob questions
Below is what I plan using for my oil return: 10AN fittings. Question: Do i need any sort of paste or compound to assemble these things? There are not any sort of rubber spacers inside. It looks as if I just need to assemble them tight and aluminum against aluminum (convex vs concave surface) should provide a tight seal. Opinions? Thanks |
|
|
|
05-17-2013, 02:47 AM
|
#2 |
|
やりすぎだ～
|
Do not use tape or paste on AN fittings. The taper seals it.
|
|
|
|
|
05-17-2013, 02:50 AM
|
#3 |
|
Drives: soarer Join Date: Feb 2011
Location: Beautiful British Columbia
Posts: 954
|
thanks
|
|
|
|
|
05-20-2013, 11:49 PM
|
#4 |
|
Drives: soarer Join Date: Feb 2011
Location: Beautiful British Columbia
Posts: 954
|
What engine oil are you (turbo heads) using?
Can I keep using Pennzoil Platinum 5w30 (that I like a lot)? |
|
|
|
|
05-21-2013, 08:54 AM
|
#5 |
|
1NZ-6spd
Drives: '05 6-Spd Vitz RS Join Date: Oct 2008
Location: Oshawa, Ontario, Canada
Posts: 2,967
|
I'm pretty sure oils will indicate in writing on the back weather they're safe for turbos or not. Full synthetics usually work best.
|
|
|
|
|
05-21-2013, 11:47 AM
|
#6 |
ULTIMATE
Drives: 07 Yaris Turbo Join Date: May 2007
Location: Canoga Park, CA
Posts: 14,859
 |
5w30 synth is good -- I don't run anything exotic. I change it a lot more often.
__________________
Micro Image forums, online store and shop are now closed. It was a great eight year run, but it was time to focus on other things. I'm still selling parts on eBay under micro*image seller ID and customers can still make requests for anything specific. |
|
|
|
|
05-21-2013, 01:21 PM
|
#7 |
|
Drives: soarer Join Date: Feb 2011
Location: Beautiful British Columbia
Posts: 954
|
^ Thanks
|
|
|
|
|
05-21-2013, 11:39 PM
|
#8 |
Drives: 08 Yaris Turbo; 06 tC Turbo Join Date: Jan 2010
Location: New Jersey
Posts: 875
|
I'd use permatex black or equivalent where the fitting connects to the inside/outside of the block. You won't be threading it into the block, as it's too thin to really grab any of the threads.
|
|
|
|
|
05-22-2013, 12:51 AM
|
#9 |
|
Drives: soarer Join Date: Feb 2011
Location: Beautiful British Columbia
Posts: 954
|
^ Thanks
This is p.black I belive. Will buy some for my install http://www.amazon.com/Permatex-82180.../dp/B0002UEN1U The scariest part right now seems to be drilling )) One does not come to drill a 18 mm hole in this engine every day )) |
|
|
|
|
05-22-2013, 01:29 AM
|
#10 |
|
ULTIMATE
Drives: 07 Yaris Turbo Join Date: May 2007
Location: Canoga Park, CA
Posts: 14,859
|
18mm? that sounds a lot larger than necessary.
__________________
Micro Image forums, online store and shop are now closed. It was a great eight year run, but it was time to focus on other things. I'm still selling parts on eBay under micro*image seller ID and customers can still make requests for anything specific. |
|
|
|
|
05-22-2013, 02:23 AM
|
#11 | |
|
Drives: soarer Join Date: Feb 2011
Location: Beautiful British Columbia
Posts: 954
|
Quote:
10AN - 18 mm oustide diameter - just measured it http://www.ebay.com/itm/181134096470...84.m1497.l2649 plaan to use something like this stepped bt |
|
|
|
|
 |
| Thread Tools | |
| Display Modes | |
|
|
Similar Threads
|
||||
| Thread | Thread Starter | Forum | Replies | Last Post |
| Zage Turbo Kit Install - Toyota Yaris | Focus_Sh1ft | Forced Induction Forum | 160 | 02-06-2022 09:14 PM |
| FS: Zage Turbo kit, AEM FIC with Pnp Harness | djgab101 | Items for Sale by private party | 32 | 04-11-2013 11:42 AM |
| Zage turbo kit | Mister Z | Forced Induction Forum | 17 | 11-26-2010 04:32 AM |
| noob here.. need help on questions about turbo and engine life | 10Kyaris | Forced Induction Forum | 43 | 10-06-2010 10:26 AM |
| zage turbo kit..! just need some help | joseyaris | Forced Induction Forum | 12 | 10-29-2009 09:35 PM |
Linear Mode
