Remote Start DIY Wiring Guide 2006-2010 Yaris

[CTScott]

Originally Posted by Yarisduder

The disconnecting the white wire to the receiver does absolutely nothing. The keyless entry works in the exact same manner as if it was connected.

Looking through the various diagrams and manuals it looks to me like the CAN bus thing is involved.

It's definitely not CAN between the Main Body ECU and the Door Control Receiver. I believe it's LIN bus, which is much easier to intercept. I need to get my hands on a door control receiver to sniff that data stream.

[chexmix]

hey ctscott.. thanks for the pdf file on the diy.. i have a question.. is there a door trigger on a 2008 yaris h/b with no power windows/locks? lmk thanks

[CTScott]

Originally Posted by chexmix

hey ctscott.. thanks for the pdf file on the diy.. i have a question.. is there a door trigger on a 2008 yaris h/b with no power windows/locks? lmk thanks

Door triggers (negative input when door is open):
FL-red wire 4A-21, FR-light blue wire 4A-24, RL-green wire 4A-5, RR-light blue wire 4A-20, Trunk/Hatch- Sky blue wire 4A-7

If the alarm only has one input for the 2 or 4 doors, you can tap all wires together.

[chexmix]

is there suppose to be any wire on the pin? cause there is none on the wire you mentioned? or just stick the wire from the alarm in the open harness that you mentioned?

[CTScott]

Originally Posted by chexmix

is there suppose to be any wire on the pin? cause there is none on the wire you mentioned? or just stick the wire from the alarm in the open harness that you mentioned?

There is no wire on any of the 5 pins listed above?

[chexmix]

yup no wires

[CTScott]

Here's a picture from Crashy, who is an 08 Liftback without power:

Door Inputs - Conn 4A - 08 LB no power copy.jpg

[CTScott]

OK - I assume your remote starter uses the DBI port?

Does the LED stay solid green when starting?

[Yaris PAVEL94]

Does anybody know how the new apps for Viper remote starters work and how to set it up? Because I'm getting my new phone( BB Curve2)next week and I want to try it.THANKS

[CTScott]

Originally Posted by Yaris PAVEL94

Does anybody know how the new apps for Viper remote starters work and how to set it up? Because I'm getting my new phone( BB Curve2)next week and I want to try it.THANKS

The ones with the cell phone interface install just like the keyfob ones. The only issue with them is that there is a monthly subscription fee for hanging it on the cell network.

[hatch2008]

ya mine is using the dbi port

[CTScott]

Originally Posted by hatch2008

ya mine is using the dbi port

OK - So that meant that you only had to wire it to the key transponder receiver.

Did the registration process go correctly (and is the module showing the green light)?

For your remote starter, what model is that?

If the remote starter didn't have a connection for key presence, the issue may be that the remote starter is telling the bypass module to send the key data at the wrong time.

[hatch2008]

the led is doing the proper lighting when flashing , i spent like 7 hours on this yesterday and made sure all that ws good .

[hatch2008]

its a prostart ct 3371 , and as far as i can tell there isnt a key sense connections jus the ign green, the white wire off the ign, the black starter wire. and the imm. hooks into the imm. connctor and obd connector .

[hatch2008]

im reading through the prostart again and notice inthe programming of the prostart im mode 3 the default is xpresskit, but my bypass is connected to the ads port , so i will try changing that becuase if that is inncorect then the prostart is looking in the wrong place for the by pass, so i could very well be an idiot today lol .. make sense too you

[hatch2008]

whats the differnece of the ign 1 wire and ign 2 wire on your diy

[hatch2008]

from what google has told me i need to have ign 1 and 2 connected to a relay which as far as i can tell my prostart instructions say is optinal, also when the car is cranking if i put the key in and to the on pos. it starts. anyone noe what i should do hear , or how the2 ign wires are suppose to be connected. starting to really hate prostart lol.

[CTScott]

Originally Posted by hatch2008

from what google has told me i need to have ign 1 and 2 connected to a relay which as far as i can tell my prostart instructions say is optinal, also when the car is cranking if i put the key in and to the on pos. it starts. anyone noe what i should do hear , or how the2 ign wires are suppose to be connected. starting to really hate prostart lol.

If you put the key in, but don't turn it, what happens?