|
|
10-06-2009, 01:00 PM | #1 |
Drives: 2008 Yaris Sedan Join Date: Oct 2008
Location: Edmonton
Posts: 393
|
HID Kit High-Beam Cluster Indicator Problem
I have done extensive searching and cannot find anyone with the same problem. I bought this kit:
http://www.retrosolutionsllc.com/ser...VERSION/Detail Its a moving type dual bi-xenon H4 kit. It operates perfectly. I has a shield which reduces glare, and when you switch to high beams, something in the bulb moves and it shifts the light upwards. The only problem is, the high-beam indicator light does not appear on the gauge cluster, which sometimes leads to forgetting that the highbeams are on, or turning them on by mistake and not realizing. Does anyone have any suggestions regarding this or have had a similar problem? I'm not sure how it works, but I have a feeling the highbeam wire actually powers a magnet that shifts the bulb, but i'm not certain, just speculating. |
10-06-2009, 01:09 PM | #2 |
Drives: '07 Yaris Sedan/'03 Protege Join Date: Oct 2008
Location: St. Augustine, FL
Posts: 260
|
Something is not wired in correctly. If you are moving your High-beam control into
the High-beam position, the dash light should come on. Judging from your location I'd guess that it has something to do with you DRLs? How did you connect those, or did you fun a bypass to shut them off? |
10-06-2009, 01:12 PM | #3 |
Drives: 2008 Yaris Sedan Join Date: Oct 2008
Location: Edmonton
Posts: 393
|
i just disconnected the whole DRL module underneath the dash. Does that somehow disable that light?
|
10-06-2009, 01:36 PM | #4 | |
ULTIMATE
Drives: 09 5dr LB, 2x 08 3dr LB Join Date: Oct 2008
Location: USA, CT
Posts: 13,460
|
Quote:
Pin 14 (gray wire) on Connector D76 (for the Sedan) should be hot with +12V at all times. Pin 11 (pink wire) goes to ground when the headlight switch is in the high beam mode. If you measure voltage on it, it should read about 1V less than pin 14 (provided that pin 14 is hot) when the high beams are off and 0V when the high beams are on. If Pin 14 is not hot, and Pin 11 measures 0V with the high beams off, you can measure resistance (Ohms) between pin 11 and ground. it should be open (OL or high value) with the high beams off and 0 Ohms with the high beams on. If Pin 14 is not hot and Pin 11 functions correctly, then the problem has to do with how the HIDs are cut in to the existing wiring. If that is the case and you can post the wiring instructions I can help further... D76 - Sedan Combo Meter.jpg |
|
10-06-2009, 02:14 PM | #5 |
ULTIMATE
Drives: 07 Yaris Turbo Join Date: May 2007
Location: Canoga Park, CA
Posts: 14,859
|
I know about this problem. There should be a leftover harness with the installation of that kit, the harness needs a resistor, then your high beam indicator will work.
PM "miniTRD", he knows the fix.
__________________
Micro Image forums, online store and shop are now closed. It was a great eight year run, but it was time to focus on other things. I'm still selling parts on eBay under micro*image seller ID and customers can still make requests for anything specific. |
10-07-2009, 06:57 PM | #6 |
It's the illusion you see
Drives: 07 Yaris Sedan Aero Join Date: Oct 2006
Location: Brossard, QC
Posts: 3,888
|
That's weird.. why does this happen to you guys?
Mine's working perfectly.. THOUGHT... my setup have one thing different that you guys... (before i did the DRL mod) my high beam indicator always worked. So.. what is different in my setup is the relay i have. My HID are directly connected to the battery with a relay.. where the oem harness switches that relay... |
12-31-2009, 06:18 PM | #7 |
Drives: Yaris & Supra Join Date: Nov 2008
Location: Here
Posts: 118
|
Did this Scott and thanks! Mine works again with the HID's. :)
Now need to know what they do since my Supra has the same problem. Duane |
02-07-2010, 08:43 PM | #8 |
Drives: 2009 RED Yaris Join Date: Feb 2010
Location: Mount Shasta Ca
Posts: 8
|
Thank you Scott & Mike!
|
02-08-2010, 06:45 AM | #9 |
Drives: no-longer-boosted '10 Yaris Join Date: Nov 2009
Location: Angus, Ontario
Posts: 1,891
|
i had the same problem when trying to disable drl's. i took out the module and was very happy for about a min.... with the module removed the DRL's, fogs and highbeams no longer worked...... u need to put that module back in but to disable the DRLs u need to cut the big blue wire (i opened up the module and cut the connectors right off the chip ) and everything works perfectly...... except the DRL's. if u are completly lost i'll try to get picks up by week end.
jsut a side note.... when i had the problem i didn't have any HID's installed so if the problem is dirrectly related to them then i dont think the module will be too much help..... give it a shot if u like
__________________
If it has boobs or wheels sooner or later your gonna have problems with it |
02-09-2010, 01:15 PM | #10 |
Bob
Drives: Yaris and Scion XD 5 spd BSP Join Date: Dec 2009
Location: Was Hawaii - Moved to Everett WA
Posts: 145
|
this is the simplest fix.
I used the right side (unused) Original Headlight socket to make these connections. 50 cents and done in a jiffy. If you want to make it "professional" looking. buy a connector from Radio Shack and fabricate the wiring on that, and plug it into the old harness. |
02-19-2010, 03:21 PM | #11 | |
Drives: 2009 RED Yaris Join Date: Feb 2010
Location: Mount Shasta Ca
Posts: 8
|
Quote:
Todd |
|
02-19-2010, 03:51 PM | #12 | |
ULTIMATE
Drives: 09 5dr LB, 2x 08 3dr LB Join Date: Oct 2008
Location: USA, CT
Posts: 13,460
|
Quote:
|
|
02-20-2010, 01:00 PM | #13 | |
Bob
Drives: Yaris and Scion XD 5 spd BSP Join Date: Dec 2009
Location: Was Hawaii - Moved to Everett WA
Posts: 145
|
Quote:
The stock harness still has related connections since nothing was ever "cut" to install the kit. Analyzing the circuit, the new low beams had no trickle circuit to the inst. cluster since it was isolated with the use of a new harness that only had connections from the ballast for power to fire the HID's the Halogen bulb actually feds the indicator circuit so without the bulbs, no indicator illumination. Also remember the ind ckt is not High beams on, but more like low beams off. |
|
02-22-2010, 02:04 AM | #14 | |
Drives: 2009 RED Yaris Join Date: Feb 2010
Location: Mount Shasta Ca
Posts: 8
|
Quote:
Todd |
|
03-02-2010, 05:44 PM | #15 | |
Quote:
can somebody post a picture for this fix! I'm not really into electronics and would like to figure out how it's done. Thanks .................
__________________
. My system may not blow your ears, but it will sweeten your senses. CLA 250, 4MATIC |
||
05-14-2010, 04:01 PM | #16 | |
Little Eggy
Drives: Toyota Yaris Liftback 3DR 2009 Join Date: Apr 2010
Location: North Plainfield, NJ
Posts: 30
|
Quote:
|
|
02-21-2010, 08:30 AM | #17 |
Drives: Yaris Join Date: Apr 2009
Location: USA
Posts: 355
|
I used CTScott's method listed above and it worked perfectly for me.
|
04-10-2010, 11:36 AM | #18 |
Yaris = <3
Drives: '08 Sedan - Flint Mica Join Date: Jan 2009
Location: Halifax, NS Canada
Posts: 217
|
Hey guys,
With the help of Bobolinko, I think I've come up with the easiest method and least invasive. Please see the attached pictures. The resistor used is a 10Kohms resistor (Brown - Black - Orange - Gold/Silver). It took only 5 minutes to put together (10 if you count the time sifting through a bag of resistors to find the right one ). With the right hand side unused headlight plug facing you, insert one spade connector into the right side of the plug and the other spade connector in the top-middle of the plug. Thanks Bobolinko for all your help and speedy responses! Greatly appreciated! I'm sure I'm not the only one who will be greatful either. Goodluck everyone and enjoy your high beam indicator!
__________________
..:'; Nick ;':.. ============================== 2008 Yaris Sedan - Flint Mica ============================== Debadged Rear; Blue Interior Styling; Toyota Sports Pedals; AM Exhaust Tip; OEM Spoiler; Upgraded Speakers; Sony Xplod BT 2600 Deck; Infinity Basslink SUB/AMP in Trunk; 16" Konig Rims; 6000k HID Bi-Xenons; 6000k HID Fogs; NST Short Shifter ============================== |
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
Yaris sedan low and high beam | jorizk | DIY / Maintenance / Service | 10 | 03-02-2010 09:49 AM |
Xenon-Vision HID Conversion Kit - $120 Shipped/$160 Shipped for Slim Ballast | phu@xenon-vision | Sponsors Classifieds Area | 8 | 03-06-2009 02:33 PM |
Hi & Lo Beam HID Conversion Kit | OgDogg | Items for Sale by private party | 0 | 11-11-2008 04:55 PM |