hmm quick help - Toyota Yaris Forums

Klinton · 04-16-2009, 04:08 AM

hey guys i know im always asking for help so here goes again lol im going to get the NST crank pulley and well here would i get this installed or is any one in the OKC area looking to make a few extra bucks lol but yeah any good places for this type of thing?

turboyaris · 04-16-2009, 12:19 PM

any mechanics shop can do it, its a pretty easy task. If they've changed a timing belt before, step 3 of that process was remove the crank pulley. it'd be easier to diy

yaris-me · 04-16-2009, 01:12 PM

Check this out.
http://www.yarisworld.com/forums/showthread.php?t=3964

Klinton · 04-16-2009, 04:38 PM

thanks !

severous01 · 04-16-2009, 08:49 PM

simple...pull the pass wheel and it's right there...all u need is a set of sockets and a pulley puller....and maybe a hammer to strike the puller. that makes pulling the OEM unit a lot easier.

any way, may as well get a new belt when u do it.

04-16-2009, 04:08 AM	#1
Klinton View User's Garage Drives: 2009 Yaris sedan Flint Mica Join Date: Mar 2009 Location: OKC Posts: 146	hmm quick help hey guys i know im always asking for help so here goes again lol im going to get the NST crank pulley and well here would i get this installed or is any one in the OKC area looking to make a few extra bucks lol but yeah any good places for this type of thing? __________________ 205/45/17 Nittos/ KN tyhoon 69 intake EURO areo muffler / DF 210 Springs NST 10% Pulley/ 15% tint 600watt rockford punch 12" subs and amp micro image rocks!

04-16-2009, 04:38 PM	#4
Klinton View User's Garage Drives: 2009 Yaris sedan Flint Mica Join Date: Mar 2009 Location: OKC Posts: 146	thanks ! __________________ 205/45/17 Nittos/ KN tyhoon 69 intake EURO areo muffler / DF 210 Springs NST 10% Pulley/ 15% tint 600watt rockford punch 12" subs and amp micro image rocks!

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
reverse gear..quick question..	Yaris2910	DIY / Maintenance / Service	10	01-11-2011 06:14 AM
Works bell/Nardi quick release steering wheel setup	blacksandiegovitz	Cosmetic Modifications (Exterior/Interior)	35	09-02-2009 06:52 PM
Quick advice needed on unfinished amp install	GreenSpeed	In Car Entertainment + Electronics (audio / video / alarm)	15	01-16-2009 12:03 AM
Stupid question...TRD Quick Shift	Stargate YARlantIS	DIY / Maintenance / Service	17	12-01-2008 12:46 AM
TRD Quick Shift & Toyota S/S Exhaust Tip	Polar	Items for Sale by private party	10	07-16-2007 03:13 AM

04-16-2009, 12:19 PM	#2
turboyaris Drives: 2007 Yaris Sedan Join Date: Jan 2007 Location: Southern New Jersey Posts: 459	any mechanics shop can do it, its a pretty easy task. If they've changed a timing belt before, step 3 of that process was remove the crank pulley. it'd be easier to diy

04-16-2009, 01:12 PM	#3
yaris-me Learn to Relax Drives: 2007, Meteorite, LB Join Date: Dec 2008 Location: Anaheim, CA Posts: 2,070	Check this out. http://www.yarisworld.com/forums/showthread.php?t=3964

04-16-2009, 08:49 PM	#5
severous01 Drives: 2008 yaris, stripped, red Join Date: Jan 2009 Location: SE Texas Posts: 977	simple...pull the pass wheel and it's right there...all u need is a set of sockets and a pulley puller....and maybe a hammer to strike the puller. that makes pulling the OEM unit a lot easier. any way, may as well get a new belt when u do it.