FS: OEM Cruise Control Stalk with Wire and Screws

[CTScott]

Originally Posted by Jadijkstra2000

It looks like the car already has the clutch switch installed, i cannot have it started when the clutch is not pressed... So i guess that one is installed...

The cruise control clutch switch is different. The starting one requires the clutch to be pressed completely to trigger, where the cruise control one triggers as soon as the clutch switch is touched.

[Jadijkstra2000]

ah alright, didn't know that, thanks :) are there ways to check if the car is prepared for cruise?

[CTScott]

Originally Posted by Jadijkstra2000

ah alright, didn't know that, thanks :) are there ways to check if the car is prepared for cruise?

The best test is to check the voltage on pin 40 of the A21 ECM connector (see my DIY below for that location). If there is 12 V on that pin with the ignition on, then cruise is present.

http://www.yarisworld.com/forums/showthread.php?t=33750

[Jadijkstra2000]

Originally Posted by CTScott

The best test is to check the voltage on pin 40 of the A21 ECM connector (see my DIY below for that location). If there is 12 V on that pin with the ignition on, then cruise is present.

http://www.yarisworld.com/forums/showthread.php?t=33750

Do I need to remove the A21 connector to do the test or leave it in place for testing?

[CTScott]

Originally Posted by Jadijkstra2000

Do I need to remove the A21 connector to do the test or leave it in place for testing?

Leave it in place. You will need to pull the rubber plug if there is not a wire present, so you can stick a piece of wire in to take the measurement.

[Mommas Yaris]

Just wondering if you have any of these left and if you do how much? If you do would you please comtact me though my email @ cgoretx@gmail.com

[CTScott]

Originally Posted by Mommas Yaris

Just wondering if you have any of these left and if you do how much? If you do would you please comtact me though my email @ cgoretx@gmail.com

email sent.

[xboxer]

Originally Posted by Mommas Yaris

Just wondering if you have any of these left and if you do how much? If you do would you please comtact me though my email @ cgoretx@gmail.com

Same question as above, including the OEM Stalk CC Pin Kit, and Cruise Control Indicator Module. Please send PM. Thanks

[CTScott]

Originally Posted by xboxer

Same question as above, including the OEM Stalk CC Pin Kit, and Cruise Control Indicator Module. Please send PM. Thanks

PM sent

[Tylard]

Do you still have any these?
07 sedan m/t. Cost as well. Thanks

[CTScott]

Originally Posted by Tylard

Do you still have any these?
07 sedan m/t. Cost as well. Thanks

Yes. PM sent.

[z0mb13k1ll]

ive got a 2007 sedan, can you pm me with the price and what i would have to do to install? thanks

[CTScott]

Originally Posted by z0mb13k1ll

ive got a 2007 sedan, can you pm me with the price and what i would have to do to install? thanks

PM sent

[Tylard]

Super fast shipping, install not too bad, fishing the wires was def the hardest part. But I cant seem to get it to function on my 07 m/t sedan. I have tried rechecking all the connections and triple check the clutch switch to ensure it is fully pressed in when the my foot is off the clutch pedal.
Any suggestions of what to check?
My wire coming out of pin 40 on the ECM is hooked up and ran through the firewall. I connected this directly to the wire coming out of the slot 1 of the D3 connector. Is this ok or do I need a different wire? If so what is it where do I get it

[CTScott]

Originally Posted by Tylard

Super fast shipping, install not too bad, fishing the wires was def the hardest part. But I cant seem to get it to function on my 07 m/t sedan. I have tried rechecking all the connections and triple check the clutch switch to ensure it is fully pressed in when the my foot is off the clutch pedal.
Any suggestions of what to check?
My wire coming out of pin 40 on the ECM is hooked up and ran through the firewall. I connected this directly to the wire coming out of the slot 1 of the D3 connector. Is this ok or do I need a different wire? If so what is it where do I get it

Double check your pin 1 and pin 2 locations per my DIY (http://www.yarisworld.com/forums/showthread.php?t=33750)

Also, with the ignition switch in the ON position, you can measure the voltage on the pin1 wire and will see 12V if it is connected properly. (Pin 1 is the one that goes to pin 40 on the ECM connector).

Also, double check your pin 40 to make sure you didn't install it on the opposite side of where it belongs.

[Tylard]

Checked pin 1 and 2 and Im happy with them. Rechecked pin 40 also happy with that.

Checked the voltage. I put my red lead on the connection between the pin 1 wire and the pin 40 ecm wire. Then I put my black lead on the bolt where pin 2 from the d3 connection is mounted. I get 12 v with the ignition turned on. Holding and toggling the cruise on/off switch does NOT make change and still reads 12 volts.

Where the pin 2 wire is mounted there is a black lead already connected to that, I just added on the pin 2 wire and put the bolt back on.

[CTScott]

Originally Posted by Tylard

Checked pin 1 and 2 and Im happy with them. Rechecked pin 40 also happy with that.

Checked the voltage. I put my red lead on the connection between the pin 1 wire and the pin 40 ecm wire. Then I put my black lead on the bolt where pin 2 from the d3 connection is mounted. I get 12 v with the ignition turned on. Holding and toggling the cruise on/off switch does NOT make change and still reads 12 volts.

Where the pin 2 wire is mounted there is a black lead already connected to that, I just added on the pin 2 wire and put the bolt back on.

Ah, the pin 2 wire is the "other side". It is the ground for the system.

The black wire is not pin two. It is in the opposite row from pin 2. In this picture you can see the blue wire in pin 1 and the brown in pin 2:

Conn D3.jpg

[Tylard]

My D3 connector looks just like the one pictured. The wires sent are different colors but going off the colors shown in the picture. The blue one connects directly to the A21 pin 40 wire. The brown one goes to a bolt (for grounding).