JUN Cams for 1NZ-FE - Page 2 - Toyota Yaris Forums

rob323 · 03-28-2011, 04:51 PM

But a 1NZ-FE doesn't have hydraulic lash adjusters or adjustable tappets, you should still re-shim the buckets to get the clearances correct.

Dylan Yap · 03-28-2011, 11:04 PM

Quote:

Originally Posted by rob323

But a 1NZ-FE doesn't have hydraulic lash adjusters or adjustable tappets, you should still re-shim the buckets to get the clearances correct.

You need to do this IF you are going for spec higher than what i have. What i using is bolt-on JUN cams 264 - 9.5 mm

Jason@SportsCar · 03-29-2011, 04:07 PM

Quote:

Originally Posted by Dylan Yap

You need to do this IF you are going for spec higher than what i have. What i using is bolt-on JUN cams 264 - 9.5 mm

There are like 16 different OE bucket part numbers (in varying thickness) for use with the stock cams. Build tolerances within the head, valves, cam and bearings are enough to require a bucket change with just a stock cam replacement.

rob323 · 03-29-2011, 04:59 PM

My point exactly, you can't even use a stock cam from another motor without having to redo the clearances.

Thirty-Nine · 03-29-2011, 05:01 PM

Cool stuff, but yikes: $800 USD per cam is a lot of dough. It is cool to see some NA builds, though.

Jason@SportsCar · 03-29-2011, 05:03 PM

Quote:

Originally Posted by rob323

My point exactly, you can't even use a stock cam from another motor without having to redo the clearances.

I am sure its fine, just send your $30k to me, I will send you a set of magic cams and a cashiers check for the balance.

rob323 · 03-29-2011, 05:12 PM

No thanks, I'll do it myself so I know it's done right.

vitz rs · 04-06-2011, 12:55 PM

Quote:

Originally Posted by Dylan Yap

You need to do this IF you are going for spec higher than what i have. What i using is bolt-on JUN cams 264 - 9.5 mm

Hi Bro, I am driving vitz rs.
just wondering where is your workshop?

Dylan Yap · 04-13-2011, 05:25 AM

Quote:

Originally Posted by vitz rs

Hi Bro, I am driving vitz rs.
just wondering where is your workshop?

Pmed you my address... great to find someone from SG here

vitz rs · 04-13-2011, 11:47 AM

Quote:

Originally Posted by Dylan Yap

Pmed you my address... great to find someone from SG here

U got mail bro.

rob323 · 04-19-2011, 05:14 PM

I see these cams are now available on Yahoo Japan.

speed1 · 05-11-2011, 03:58 PM

I read all of your stories.
Super Mega cams for 1nzfe.
If u look at Jun site there are only 2 specs for 1nzfe:
9,0-63 (bolt-on series) and 9,5-66 (regular series).
If 9,5-66 rev limit move e vvt-i manage required
to have best.

03-29-2011, 05:01 PM	#23
Thirty-Nine Small cars are a big deal View User's Garage Drives: 2007 Yaris Liftback Join Date: Feb 2006 Location: Portland, OR Posts: 3,144	Cool stuff, but yikes: $800 USD per cam is a lot of dough. It is cool to see some NA builds, though. __________________ Subcompact Culture: The Small car blog

05-11-2011, 03:58 PM	#30
speed1 Drives: vitz rs Join Date: Apr 2011 Location: Lecco-Italy Posts: 77	The True I read all of your stories. Super Mega cams for 1nzfe. If u look at Jun site there are only 2 specs for 1nzfe: 9,0-63 (bolt-on series) and 9,5-66 (regular series). If 9,5-66 rev limit move e vvt-i manage required to have best. Last edited by speed1; 05-28-2012 at 07:25 AM.

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
JUN Releases Camshafts for the 1NZ-FE	changchewsoon	Performance Modifications	53	01-23-2017 09:28 PM
JUN Auto Releases High Lift Camshafts for Toyota 1NZ-FE	changchewsoon	Performance Modifications	7	02-16-2011 04:46 PM
Gude cams "NOT SO NACHO"	xbgod	Performance Modifications	77	01-27-2011 02:45 PM
JUN Auto - 1NZ-FE I-Beam Connecting Rods	changchewsoon	Forced Induction Forum	10	04-19-2010 12:00 PM
GI: Custom Cams	lilredrocket	Performance Modifications	62	11-13-2009 11:10 AM

03-28-2011, 04:51 PM	#19
rob323 Don't drive it, RALLY it! Drives: 1999 echo PRC rally car Join Date: Oct 2008 Location: Joyner, Brisbane Posts: 321	But a 1NZ-FE doesn't have hydraulic lash adjusters or adjustable tappets, you should still re-shim the buckets to get the clearances correct.

03-29-2011, 04:59 PM	#22
rob323 Don't drive it, RALLY it! Drives: 1999 echo PRC rally car Join Date: Oct 2008 Location: Joyner, Brisbane Posts: 321	My point exactly, you can't even use a stock cam from another motor without having to redo the clearances.

03-29-2011, 05:12 PM	#25
rob323 Don't drive it, RALLY it! Drives: 1999 echo PRC rally car Join Date: Oct 2008 Location: Joyner, Brisbane Posts: 321	No thanks, I'll do it myself so I know it's done right.

04-19-2011, 05:14 PM	#29
rob323 Don't drive it, RALLY it! Drives: 1999 echo PRC rally car Join Date: Oct 2008 Location: Joyner, Brisbane Posts: 321	I see these cams are now available on Yahoo Japan.