Remote Start DIY Wiring Guide 2006-2010 Yaris

[bad_bwoy007]

Thanks for the quick response.

So is this how the relay should be hooked up?



If so, what would you use as you 12 volt pulse to activate the relay?

The Starter output?

PIN-1 YELLOW Starter Output-This wire will test 0V when the key is off, in the Accessory position and when
the Ignition is in the on position. The starter wire is 12volts during the start/ crank position only.

[CTScott]

Originally Posted by bad_bwoy007

Thanks for the quick response.

So is this how the relay should be hooked up?



If so, what would you use as you 12 volt pulse to activate the relay?

The Starter output?

PIN-1 YELLOW Starter Output-This wire will test 0V when the key is off, in the Accessory position and when
the Ignition is in the on position. The starter wire is 12volts during the start/ crank position only.

Correct - The starter output wire should feed the relay coil.

[bad_bwoy007]

Thanks for all the help. You are the man.

[bad_bwoy007]

CTScott,

Got so troubles here with the install.



I'm just doing a quick test to see if I could get the system to start.

I have the:
Yellow(Output to starter circuit) to Black(Yaris - Starter)
Green(Output to ACC circuit) to White(Yaris - ACC)
Red
Red
*Both Red wires tapped together then into the 12v fuse location.
White(2nd IGN) to Pink(Yaris - IGN#2)
Blue(IGN circuit) to Green(Yaris - IGN#1)

For now I am just pressing the clutch switch with my hand, will bypass it later.

Only thing I can think of is if my wiretaps didn't make solid connections. I did undo and redo some to verify there where connecting.

Currently I am simulating the system:
I have the system ground connected to ground.

On the 13 wire connection, I only need the Brake switch, park brake, and door input for now.

I also attempted the reservation mode to no avail.

MANUAL TRANSMISSION INSTALL MANUAL SYSTEM PROGRAMMING - Menu 1
RESERVATION MODE
Manual transmission remote starters must be set into Reservation Mode before the remote starter will activate. The activation type of Reservation Mode is determined when the system is installed.
Auto Reservation Mode (Default) 1- While the vehicle is running, place into neutral and apply the park brake.
2*- Press and release the brake pedal twice. The park lights will flash twice, the SIREN or HORN (opt.) will chirp twice and the doors will unlock (opt.). 3-Turn the ignition key off and the vehicle will continue running. 4**- Within 30 seconds, exit the vehicle and close all the doors. The vehicle will then shut off .
Manual Reservation Mode (Optional) 1- While the vehicle is running with the key, place transmission into neutral
and apply the park brake. 2- Press and release the START button. The park lights will flash twice, the SIREN or HORN (opt.) will chirp twice and the doors will unlock (opt.). 3- Turn the ignition key off and the vehicle will continue running. 4- Exit the vehicle and close all the doors. 5**- Press and hold the START button for 3 seconds, the vehicle will then shut off.
* If the park lights do not flash and stay on or the SIREN (HORN optional) chirps a third time, repeat Step 2. ** If the vehicle has dome light delay, the vehicle may stay running until the dome light turns off. This is normally no longer than 30 seconds.
**TEST RESERVATION MODE**
1) Press the start button on the remote without setting the Reservation Mode. The park lights should flash 4 times without starting the vehicle. If the vehicle starts THE WRONG REMOTE STARTER HAS BEEN INSTALLED!!!
2) Set the Reservation Mode then remote start the vehicle. Shut off with the remote wait 10 seconds then open the passenger door. Press Start on the remote and Reservation Mode should be cancelled. (4 flashes) if not, check for proper door pin connections.
*****FOR SAFETY REASONS ALL DOOR PINS INCLUDING THE REAR HATCH MUST BE CONNECTED.******

Any ideas?