NST (NonStopTuning) Pulleys. Info, Specs, User Data... - Page 15 - Toyota Yaris Forums

battleversiontc · 10-26-2008, 03:27 PM

i let you know by today i have to install it on my gfs car which is an automatic

ZING · 10-26-2008, 03:33 PM

Quote:

Originally Posted by battleversiontc

i let you know by today i have to install it on my gfs car which is an automatic

Excellent, thanks

lamdog · 10-28-2008, 10:58 AM

received a underdrive pulley from Gram today..
tried to fit it, but no luck... the bolt is freaking hard.
i have also tried an electric drill to take it off, the bolt did not move at all.
sighs... gonna take the pulley to my mechanic this weekend, i cannot wait....

battleversiontc · 10-29-2008, 12:05 AM

yeah i had to use an impact gun to remove the bolt for the crank
and a 10mm wrench for the water pump pulley along with a thick srew driver through the holes to loosen the water pump pulley bolts and i just impacted the alt pulley it was all good after that

lamdog · 10-31-2008, 09:32 AM

got my underdrive pulley on today...
took it to my mechanic, it was just a piece of cake with air tool....
i could notice that the throttle is much lighter right after the pulley was on...
no unusual vibration after.

NonStopTuning · 11-05-2008, 01:28 AM

Thank you sir

battleversiontc · 11-06-2008, 02:11 AM

im waiting to find out the differences with the mpg on these i hope to see alot of improvement on this since now i dont really push the gas down as much now

NonStopTuning · 11-20-2008, 05:03 PM

Quote:

Originally Posted by richardholdener

Here are the official results of an honest back-to-back dyno test of the NST pulleys (crank, alt & WP). Car was run on the dyno with stock pulleys and then we swapped out the stock pulleys for the NST (I believe 10% under driven) though sizing on WP and Alt looked the same. Pulleys were definitely worth some power as indicated by grpah. Note also the power numbers (123 wheel hp) is a new NA record-posted elsewhere with description of mods.

Thanks again Richard, your hard work and dedication is much appreciated

*MAD DOG* · 11-20-2008, 08:35 PM

Quote:

Originally Posted by NonStopTuning

Thanks again Richard, your hard work and dedication is much appreciated

Is that dyno a stock car vs the same stock car with stock pulleys removed and NST pulleys (including 10% underdrive)? Were there no other engine/exhaust mods?

CASTREX · 11-20-2008, 08:54 PM

Quote:

Originally Posted by *MAD DOG*

Is that dyno a stock car vs the same stock car with stock pulleys removed and NST pulleys (including 10% underdrive)? Were there no other engine/exhaust mods?

There are a lot of other modifications on that Dyno chart. Intake Manifold, custom long tube header, and others.

However, is important to mention that NON of those other mods modify in no way the output / gains provided by the pulleys.

That means that the 3whp gain all across the power band will be the same on an unmodified car.

And yes, that is a complete pulley set including the 10% underdrive crank pulley.

RagnaCaT · 11-20-2008, 08:41 PM

One with pulleys and one without thats about 3hp!

*MAD DOG* · 11-20-2008, 08:57 PM

^
Thanks for clearing that up.

NonStopTuning · 11-21-2008, 03:18 PM

And now some breaking news from NNN (NST News Network)

75% lighter than OEM.
Slight underdriving of accessories EXCEPT alternator.
Hard anodized aluminum.

More info...
http://nonstoptuning.blogspot.com/20...-yaris-ts.html

mikenacarato · 11-21-2008, 03:47 PM

very nice! btw Mike i had a problem installing my short shifter. it did not slide on very easy with out me having to grind out the bottom a little. just fyi...but other than that..TOP NOTCH!!! love the new shifts

Thej3sta2 · 11-21-2008, 04:02 PM

gangsta leen

NonStopTuning · 11-21-2008, 07:11 PM

Quote:

Originally Posted by Thej3sta2

gangsta leen

NST pulleys are GANGSTA

RagnaCaT · 11-21-2008, 06:16 PM

Can't see PICS!

NonStopTuning · 11-21-2008, 07:12 PM

Quote:

Originally Posted by RagnaCaT

Can't see PICS!

Really?! Anyone else having a problem with the pics?

10-26-2008, 03:27 PM	#1
battleversiontc View User's Garage Drives: 08 vip yaris Join Date: Oct 2008 Location: 808 Posts: 501	i let you know by today i have to install it on my gfs car which is an automatic __________________ 08 junction produce belta almost done and ready for paint 06 junction produce tc 604 bhp 445tq ddriven still trying for 700+hp 90 crx sir ls vtec turbo 755 hp mecp masters certified

10-29-2008, 12:05 AM	#4
battleversiontc View User's Garage Drives: 08 vip yaris Join Date: Oct 2008 Location: 808 Posts: 501	yeah i had to use an impact gun to remove the bolt for the crank and a 10mm wrench for the water pump pulley along with a thick srew driver through the holes to loosen the water pump pulley bolts and i just impacted the alt pulley it was all good after that __________________ 08 junction produce belta almost done and ready for paint 06 junction produce tc 604 bhp 445tq ddriven still trying for 700+hp 90 crx sir ls vtec turbo 755 hp mecp masters certified

11-05-2008, 01:28 AM	#6
NonStopTuning Drives: NST CARS: S13 AE86 ANT10 AW11 Join Date: Dec 2006 Location: USA Posts: 1,097	Thank you sir __________________ MIKE @ NST www.NonStopTuning.com

11-06-2008, 02:11 AM	#7
battleversiontc View User's Garage Drives: 08 vip yaris Join Date: Oct 2008 Location: 808 Posts: 501	im waiting to find out the differences with the mpg on these i hope to see alot of improvement on this since now i dont really push the gas down as much now __________________ 08 junction produce belta almost done and ready for paint 06 junction produce tc 604 bhp 445tq ddriven still trying for 700+hp 90 crx sir ls vtec turbo 755 hp mecp masters certified

11-20-2008, 08:41 PM	#11
RagnaCaT HacKers WanTed! View User's Garage Drives: Yaris S HB & Yaris S SD Join Date: Aug 2007 Location: Villalba, Puerto Rico Posts: 435	One with pulleys and one without thats about 3hp! __________________ *R-CaT* Project Yar 2ZR

10-28-2008, 10:58 AM	#3
lamdog View User's Garage Drives: Yaris YRX Join Date: Oct 2008 Location: Perth Australia Posts: 29	received a underdrive pulley from Gram today.. tried to fit it, but no luck... the bolt is freaking hard. i have also tried an electric drill to take it off, the bolt did not move at all. sighs... gonna take the pulley to my mechanic this weekend, i cannot wait....

10-31-2008, 09:32 AM	#5
lamdog View User's Garage Drives: Yaris YRX Join Date: Oct 2008 Location: Perth Australia Posts: 29	got my underdrive pulley on today... took it to my mechanic, it was just a piece of cake with air tool.... i could notice that the throttle is much lighter right after the pulley was on... no unusual vibration after.

11-20-2008, 08:57 PM	#12
MAD DOG Drives: 2011 Toyota Camry Hybrid Join Date: Oct 2008 Location: Victoria, Australia Posts: 6,412	^ Thanks for clearing that up. __________________ "Manual labour is not for me. In fact i'm not even sure non manual work is either." -Anthony Linton Check out ▬▬► I like I like ◄▬▬ for more fun on Facebook

11-21-2008, 03:18 PM	#13
NonStopTuning Drives: NST CARS: S13 AE86 ANT10 AW11 Join Date: Dec 2006 Location: USA Posts: 1,097	And now some breaking news from NNN (NST News Network) 75% lighter than OEM. Slight underdriving of accessories EXCEPT alternator. Hard anodized aluminum. More info... http://nonstoptuning.blogspot.com/20...-yaris-ts.html __________________ MIKE @ NST www.NonStopTuning.com Last edited by NonStopTuning; 11-21-2008 at 07:31 PM.

11-21-2008, 03:47 PM	#14
mikenacarato SIPNDEW View User's Garage Drives: 15 STI Join Date: Oct 2008 Location: Brentwood, TN Posts: 2,281	very nice! btw Mike i had a problem installing my short shifter. it did not slide on very easy with out me having to grind out the bottom a little. just fyi...but other than that..TOP NOTCH!!! love the new shifts

11-21-2008, 04:02 PM	#15
Thej3sta2 Drives: Soon to be LFA Join Date: Oct 2008 Location: Orlando, FL Posts: 523	gangsta leen __________________

11-21-2008, 06:16 PM	#17
RagnaCaT HacKers WanTed! View User's Garage Drives: Yaris S HB & Yaris S SD Join Date: Aug 2007 Location: Villalba, Puerto Rico Posts: 435	Can't see PICS! __________________ *R-CaT* Project Yar 2ZR

Thread Tools
Show Printable Version Email this Page
Display Modes
Switch to Linear Mode Hybrid Mode Switch to Threaded Mode