in need of some help!!!

[aznofmuff]

so what do i do with the multimeter? do i measure the current or the voltage or the resistance?! id so how do i measure the voltagee without the battery and etc... thanks again!

[CTScott]

Originally Posted by aznofmuff

so what do i do with the multimeter? do i measure the current or the voltage or the resistance?! id so how do i measure the voltagee without the battery and etc... thanks again!

Voltage. Stick the tip of the red lead into the back of the connector, touching the metal of the pin while holding the tip of the black lead to a ground (the metal body of the key switch is fine as the ground).

Measure first with the ignition off and key out and then a second time with the key in and rotated to start. Record the voltage seen on each color wire in both of those modes.

[aznofmuff]

hey scott, these are the measurements i recorded for the wires.
GREY [ 14.4v off, 14.4v on, 14.4 v start]
YELLOW [ 14.4 off, 14.4 on, 14.4 start]
BLACK [0v off, 0.01 v on, 14.4 v start]
PINK [0v off, 14.3 on, 14.4 start ]
WHITe [0 off, 14.33 on, 0 start]
GREEN [0 v off, 14.43 on, 14.43 start]

thanks!

[CTScott]

Originally Posted by aznofmuff

hey scott, these are the measurements i recorded for the wires.
GREY [ 14.4v off, 14.4v on, 14.4 v start]
YELLOW [ 14.4 off, 14.4 on, 14.4 start]
BLACK [0v off, 0.01 v on, 14.4 v start]
PINK [0v off, 14.3 on, 14.4 start ]
WHITe [0 off, 14.33 on, 0 start]
GREEN [0 v off, 14.43 on, 14.43 start]

thanks!

OK - That is all correct.

What I would like you to do next is to swap two relays for me in the under hood fuse panel, to see if the ST relay is bad.

In the diagram below of the fuse box there is the "HTR SUB1" Relay and the *10 Relay (which is the "ST" relay). They are both the same type of relay, so you can safely switch them for a test. Swap them and then try to start it.

[aznofmuff]

hey scottt i tried putting a 9v battery t the relay and i don't hear anything!!! does this mean that the relay is broken?!!?! thankss again!!!!!!

[CTScott]

Originally Posted by aznofmuff

hey scottt i tried putting a 9v battery t the relay and i don't hear anything!!! does this mean that the relay is broken?!!?! thankss again!!!!!!

It likely does. Mine clicks loudly when I do it. Do you have fog lights? If so, you can swap that relay, which is on the side of the under-dash fuse panel.

[aznofmuff]

ohh nevermind it does click... my bad sorry. so what should i do now?!

[CTScott]

Originally Posted by aznofmuff

ohh nevermind it does click... my bad sorry. so what should i do now?!

Put the relay back in, put your ear right against it, and have someone else turn the key to the start position and see if it clicks while in circuit.

[aznofmuff]

hey scott yeah it does click when the ignition is turned on. what should i check next/!?!! many thanks yet again!!

[CTScott]

Originally Posted by aznofmuff

hey scott yeah it does click when the ignition is turned on. what should i check next/!?!! many thanks yet again!!

Is that one clicking when the key is turned to "START" or is one clicking when it is turned to "ON"?

If that one is definitely the clicking one, then the next thing to try is to pull the relay and using a piece of wire, jump the other two contacts on the relay socket (other two from the ones that you touched the battery to above). Don't fully insert the wire in to the two terminals, but rather just touch it between them,

When you do so, it will make a good spark and theoretically the starter should spin.

[aznofmuff]

stil nothing... i put the wire across and started the engine but it doesnt wanna do anything... is there anything else u can recommend?! thanks again

[lablab]

If I were you, go the nearest auto shop and let the professional handle it. It might worsen the case if you yourself will touch it,.