Looking at seats... - Page 4 - Toyota Yaris Forums

MGargano · 08-07-2009, 05:31 PM

CTScott · 08-07-2009, 05:31 PM

Much better...

CTScott · 08-07-2009, 05:40 PM

If I end up picking up the wrecked eBay Yaris, I'll have a set of seats to mess with the sensors. They appear to be resistive load cells.

Is there enough space under the new seat for the Occupant Classification ECU?

MGargano · 08-07-2009, 05:42 PM

Is that this guy?

CTScott · 08-07-2009, 05:44 PM

Yes. He'll need to still be connected.

MGargano · 08-07-2009, 05:45 PM

Not really any room under the seat or on the brackets:

MGargano · 08-07-2009, 05:46 PM

Is it safe to just lay it on the floor under the seat?

MGargano · 08-07-2009, 05:53 PM

Scratch that... I can attach it to the front of the bracket

CTScott · 08-07-2009, 05:59 PM

How about the seat belts - Are you going to use the exiting or replace them with harnesses?

MGargano · 08-07-2009, 06:01 PM

Quote:

Originally Posted by CTScott

How about the seat belts - Are you going to use the exiting or replace them with harnesses?

I'm using the existing belts. I already removed the seat belts from the old seats and bolted them to the new ones.

MGargano · 08-07-2009, 06:01 PM

Booya!

MGargano · 08-07-2009, 06:08 PM

Apparently the driver's side seat belt is not the same as the passenger's side. Driver's side is plugged into this:

MGargano · 08-07-2009, 06:10 PM

No idea what this is, but it's magnetic... stuck to the rail when I removed the torx screw holding it in.

MGargano · 08-07-2009, 06:35 PM

I attached it to the driver's side bracket. Seat belts officially swapped!

MGargano · 08-07-2009, 06:56 PM

*patiently awaits the next step*

MGargano · 08-07-2009, 08:01 PM

Ok, I plugged the 3.3 ohm resistors into the airbag sensors and installed 10k ohm resistors between Pin 1 (SVC) and Pin 2 (SIG) and 470 ohm resistor between Pins 2 & 3...

I'm getting the SRS warning light in the instrument cluster, Passenger Airbag 'Off' and passenger seat belt light blinking....

MGargano · 08-07-2009, 08:08 PM

...so now I'm totally lost. Help!

CTScott · 08-07-2009, 09:24 PM

Did you disconnect the battery while you were unplugging the airbag, etc? If not, disconnect it for a couple of minutes and then reconnect it to reset the SRS ECU.

Thread Tools
Show Printable Version Email this Page
Display Modes
Switch to Linear Mode Hybrid Mode Switch to Threaded Mode

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
Possible Group Buy.. Racing Seats, Intakes?	TinyGiant	Items for Sale by private party	60	09-11-2009 03:40 PM
FS: Recaro Pole Position Racing Seats (black) -- socal	03Z33	Items for Sale by private party	13	12-07-2008 06:08 PM
sparco seats and pedals (pics)	turboyaris	Cosmetic Modifications (Exterior/Interior)	18	09-05-2007 03:43 AM
Sport / Racing seats worth the while?	mikeukrainetz	Cosmetic Modifications (Exterior/Interior)	10	11-19-2006 02:17 PM
Yaris Liftback Seats	artyin	General Yaris / Vitz Discussion	3	04-30-2006 05:07 PM

08-07-2009, 05:31 PM	#1
MGargano Drives: 2009 Yaris Hatchback Join Date: Feb 2009 Location: NJ Posts: 792

08-07-2009, 05:31 PM	#2
CTScott ULTIMATE View User's Garage Drives: 09 5dr LB, 2x 08 3dr LB Join Date: Oct 2008 Location: USA, CT Posts: 13,460	Much better...

08-07-2009, 05:40 PM	#3
CTScott ULTIMATE View User's Garage Drives: 09 5dr LB, 2x 08 3dr LB Join Date: Oct 2008 Location: USA, CT Posts: 13,460	If I end up picking up the wrecked eBay Yaris, I'll have a set of seats to mess with the sensors. They appear to be resistive load cells. Is there enough space under the new seat for the Occupant Classification ECU?

08-07-2009, 05:42 PM	#4
MGargano Drives: 2009 Yaris Hatchback Join Date: Feb 2009 Location: NJ Posts: 792	Is that this guy?

08-07-2009, 05:44 PM	#5
CTScott ULTIMATE View User's Garage Drives: 09 5dr LB, 2x 08 3dr LB Join Date: Oct 2008 Location: USA, CT Posts: 13,460	Yes. He'll need to still be connected.

08-07-2009, 05:45 PM	#6
MGargano Drives: 2009 Yaris Hatchback Join Date: Feb 2009 Location: NJ Posts: 792	Not really any room under the seat or on the brackets:

08-07-2009, 05:46 PM	#7
MGargano Drives: 2009 Yaris Hatchback Join Date: Feb 2009 Location: NJ Posts: 792	Is it safe to just lay it on the floor under the seat?

08-07-2009, 05:53 PM	#8
MGargano Drives: 2009 Yaris Hatchback Join Date: Feb 2009 Location: NJ Posts: 792	Scratch that... I can attach it to the front of the bracket

08-07-2009, 05:59 PM	#9
CTScott ULTIMATE View User's Garage Drives: 09 5dr LB, 2x 08 3dr LB Join Date: Oct 2008 Location: USA, CT Posts: 13,460	How about the seat belts - Are you going to use the exiting or replace them with harnesses?

08-07-2009, 06:01 PM	#11
MGargano Drives: 2009 Yaris Hatchback Join Date: Feb 2009 Location: NJ Posts: 792	Booya!

08-07-2009, 06:08 PM	#12
MGargano Drives: 2009 Yaris Hatchback Join Date: Feb 2009 Location: NJ Posts: 792	Apparently the driver's side seat belt is not the same as the passenger's side. Driver's side is plugged into this:

08-07-2009, 06:10 PM	#13
MGargano Drives: 2009 Yaris Hatchback Join Date: Feb 2009 Location: NJ Posts: 792	No idea what this is, but it's magnetic... stuck to the rail when I removed the torx screw holding it in.

08-07-2009, 06:35 PM	#14
MGargano Drives: 2009 Yaris Hatchback Join Date: Feb 2009 Location: NJ Posts: 792	I attached it to the driver's side bracket. Seat belts officially swapped!

08-07-2009, 06:56 PM	#15
MGargano Drives: 2009 Yaris Hatchback Join Date: Feb 2009 Location: NJ Posts: 792	patiently awaits the next step

08-07-2009, 08:01 PM	#16
MGargano Drives: 2009 Yaris Hatchback Join Date: Feb 2009 Location: NJ Posts: 792	Ok, I plugged the 3.3 ohm resistors into the airbag sensors and installed 10k ohm resistors between Pin 1 (SVC) and Pin 2 (SIG) and 470 ohm resistor between Pins 2 & 3... I'm getting the SRS warning light in the instrument cluster, Passenger Airbag 'Off' and passenger seat belt light blinking....

08-07-2009, 08:08 PM	#17
MGargano Drives: 2009 Yaris Hatchback Join Date: Feb 2009 Location: NJ Posts: 792	...so now I'm totally lost. Help!

08-07-2009, 09:24 PM	#18
CTScott ULTIMATE View User's Garage Drives: 09 5dr LB, 2x 08 3dr LB Join Date: Oct 2008 Location: USA, CT Posts: 13,460	Did you disconnect the battery while you were unplugging the airbag, etc? If not, disconnect it for a couple of minutes and then reconnect it to reset the SRS ECU.