|
04-21-2013, 03:14 AM | #1 |
Drives: 07 BB yaris / 06 Mustang Gt Join Date: Apr 2007
Location: northern california
Posts: 136
|
Putting on dust cover boot ring on ball joint
Is there special tool to install dust boot cover ring on ball joint?
|
04-21-2013, 03:15 AM | #2 |
Drives: 07 BB yaris / 06 Mustang Gt Join Date: Apr 2007
Location: northern california
Posts: 136
|
:(
|
04-21-2013, 03:23 AM | #3 |
Drives: 07 BB yaris / 06 Mustang Gt Join Date: Apr 2007
Location: northern california
Posts: 136
|
This happened after using ball joint fork
|
04-21-2013, 03:25 AM | #4 |
Drives: 07 BB yaris / 06 Mustang Gt Join Date: Apr 2007
Location: northern california
Posts: 136
|
.
|
04-21-2013, 07:43 AM | #5 |
ULTIMATE
Drives: 09 5dr LB, 2x 08 3dr LB Join Date: Oct 2008
Location: USA, CT
Posts: 13,460
|
Did you rip the new boot by trying to use the for to get that ring on?
I would probably try two pairs of locking pliers to hold the ends while pulling them apart to get the clip into place. There is a special tool for spreading that type of clip, but it may not be something that you could get from a local autoparts store.
__________________
|
04-21-2013, 11:37 AM | #6 |
Drives: Prius C Join Date: Feb 2013
Location: US
Posts: 240
|
What Scott said. There are some special pliers. I've gotten them from sears before. Craftsman.
|
04-21-2013, 12:27 PM | #7 |
Drives: 08 Yaris Sedan Join Date: Oct 2008
Location: California - Bay Area
Posts: 2,773
|
I hate using pickle forks on the ball joint it always garentees you will damage the boot. This is the actual tool and brand I keep in my tool box for this job
http://www.youtube.com/watch?v=7vweCmGwBiU Its about 20 bucks at harbor freight or around 50 for the entire master kit.
__________________
|
04-21-2013, 12:40 PM | #8 |
Drives: 07 BB yaris / 06 Mustang Gt Join Date: Apr 2007
Location: northern california
Posts: 136
|
No, that's old stock boot and new one still good. I tried to spread using two locking pliers but it doesn't spread enough to fit. Looks like i need special tool
|
04-21-2013, 12:41 PM | #9 |
Drives: 07 BB yaris / 06 Mustang Gt Join Date: Apr 2007
Location: northern california
Posts: 136
|
|
04-21-2013, 12:42 PM | #10 | |
Drives: 07 BB yaris / 06 Mustang Gt Join Date: Apr 2007
Location: northern california
Posts: 136
|
Yep I used that to remove it after fork failed
Quote:
|
|
04-21-2013, 12:51 PM | #11 |
Drives: 07 BB yaris / 06 Mustang Gt Join Date: Apr 2007
Location: northern california
Posts: 136
|
Can I use this to lubricate ball joint?? Thank you
|
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
Clazzio Seat Cover DIY Install | PETERPOOP | DIY / Maintenance / Service | 31 | 09-10-2010 03:30 PM |
Ball Joint on Bottom Arm | David Godfrey | DIY / Maintenance / Service | 1 | 04-18-2010 06:27 PM |
DIY Needed removal of entire e brake boot cover if it is possible? | YarisSedan | DIY / Maintenance / Service | 5 | 12-18-2009 05:23 AM |
07-08 Shift boot and ring | schleppy | Willing to Buy by private party | 13 | 11-30-2009 03:06 AM |