Intake HP Increases - Page 2 - Toyota Yaris Forums

LtNoogie · 05-06-2009, 07:20 PM

Yes, thanks for the catch. Corrected.

808_Yaris · 05-06-2009, 07:40 PM

Or you could get a carbon fiber intake. kargoboy (yarisuniverse) has one left!

slvryaris · 05-06-2009, 08:27 PM

I would do the AFE. I had the AEM for a while and had problems with getting the filter wet and eerything was installed as it should be.

kurokoma-kun · 05-06-2009, 10:34 PM

I also have the AEM, works great, love the sound it makes

Quote:

Originally Posted by Astroman

I love my AEM, and with my foglight cover mod it reduced the intake temperature by 10 degrees.

Ah, Astroman! I coulda sworn someone did this but could not remember who or find a pic! I just sold my foglights and will be making the same type vent soon--did you back yours with any kind of mesh? did you use a dremel or utility knife?

lilredrocket · 05-08-2009, 12:33 AM

^ I did the same thing and didn't use mesh. I used a utility knife to cut mine out

b00sted4fun · 05-08-2009, 08:51 AM

Quote:

Originally Posted by lilredrocket

^ I did the same thing and didn't use mesh. I used a utility knife to cut mine out

is there any kind of routing that needs to be doen to push the air to the intake?

kurokoma-kun · 05-08-2009, 10:30 AM

The people who've done this for brake duct cooling added dryer vent hose or similar to direct the air; I'm just gonna cut the slots out and go from there.

LtNoogie · 05-08-2009, 10:49 AM

Quote:

Originally Posted by kurokoma-kun

The people who've done this for brake duct cooling added dryer vent hose or similar to direct the air; I'm just gonna cut the slots out and go from there.

I bought 10' of RV sewer hose.

lilredrocket · 05-09-2009, 12:43 AM

Since my engine is sucking air from inside the bumper i didn't use any ducting. I might go back and put in some later on but I figure for on that will help air circulate in ther more than before

anonymous user · 05-09-2009, 06:57 AM

Am I the only one with a Blitz intake on this forum?

PETERPOOP · 05-09-2009, 02:03 PM

don't think so. i think t-sport and the other guy with the blitz spondered s/c car has one too

eric81 · 05-09-2009, 05:25 PM

Blitz makes an intake?

j/k

05-06-2009, 07:20 PM	#19
LtNoogie View User's Garage Drives: '08 Bayou Blue LB AT Join Date: Oct 2008 Location: West Hills, CA Posts: 2,517	Yes, thanks for the catch. Corrected. __________________ aFe Intake \| Blitz Supercharger \| Megan Header \| TRD Exhaust \| NST Pulley Set TRD Shocks/Struts \| Tanabe NF210 Springs \| TRD Sway Bar \| Motegi TRAKLITE wheels \| Kuhmo Ecsta XS R1 Concepts slotted rotors \| Carbotech 1521 brake pads \| stainless steel brake lines \| Seibon vented carbon fiber hood

05-09-2009, 06:57 AM	#28
anonymous user rarer than JDM -1 of 1! View User's Garage Drives: 07yaris Join Date: Oct 2008 Location: windward oahu Posts: 402	Am I the only one with a Blitz intake on this forum? __________________ It's not what you drive, or how much $$ you throw at the car. Mod the ballast on the front left first!

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
DIY: Intake Installation	redyaris	DIY / Maintenance / Service	53	08-23-2014 06:34 AM
MY new PRM Intake...	marcus	Performance Modifications	27	05-04-2009 12:04 AM
Bomz Ebay Intake - Partial Review	Split	Performance Modifications	11	11-19-2008 03:12 AM
Intake Systems Decision Maker..	Blenjar	Performance Modifications	25	09-15-2007 11:07 PM
WR Secret Weapon Intake Dyno Tested..	WRLEO	Performance Modifications	70	05-17-2007 04:00 PM

05-06-2009, 07:40 PM	#20
808_Yaris Where is Oahu? View User's Garage Drives: 5-door meteorite metallic Join Date: Dec 2008 Location: HI Posts: 1,346	Or you could get a carbon fiber intake. kargoboy (yarisuniverse) has one left!

05-06-2009, 08:27 PM	#21
slvryaris View User's Garage Drives: 2007 Yaris Sedan S Join Date: May 2006 Location: Indiana Posts: 885	I would do the AFE. I had the AEM for a while and had problems with getting the filter wet and eerything was installed as it should be.

05-08-2009, 12:33 AM	#23
lilredrocket Slowy getting there View User's Garage Drives: 08 Liftback Join Date: Nov 2008 Location: DFW, Texas Posts: 1,464	^ I did the same thing and didn't use mesh. I used a utility knife to cut mine out

05-08-2009, 10:30 AM	#25
kurokoma-kun Drives: 2007 Yaris HB Join Date: Apr 2007 Location: my own little world Posts: 1,256	The people who've done this for brake duct cooling added dryer vent hose or similar to direct the air; I'm just gonna cut the slots out and go from there.

05-09-2009, 12:43 AM	#27
lilredrocket Slowy getting there View User's Garage Drives: 08 Liftback Join Date: Nov 2008 Location: DFW, Texas Posts: 1,464	Since my engine is sucking air from inside the bumper i didn't use any ducting. I might go back and put in some later on but I figure for on that will help air circulate in ther more than before

05-09-2009, 02:03 PM	#29
PETERPOOP View User's Garage Drives: 08 white liftback Join Date: Oct 2008 Location: Oahu Posts: 3,674	don't think so. i think t-sport and the other guy with the blitz spondered s/c car has one too

05-09-2009, 05:25 PM	#30
eric81 View User's Garage Drives: Toyota Salesman Join Date: Nov 2008 Location: Clarksville, IN Posts: 297	Blitz makes an intake? j/k