Led headlights?

[IllusionX]

They are aimed exactly the same height. It's the way the headlights are made for LHD, passenger side always angles up toward road side signs.

Sent from my SM-G930W8 using Tapatalk

[Exiwolfman]

Originally Posted by IllusionX

They are aimed exactly the same height. It's the way the headlights are made for LHD, passenger side always angles up toward road side signs.

Sent from my SM-G930W8 using Tapatalk

Yup it does

Sent from my SM-G935F using Tapatalk

[Kaotic Lazagna]

Originally Posted by Exiwolfman

Passenger side can stay higher it's the driver side that should be lower so one does not blind on coming traffic or both even works well too.

Sent from my SM-G935F using Tapatalk

Originally Posted by IllusionX

They are aimed exactly the same height. It's the way the headlights are made for LHD, passenger side always angles up toward road side signs.

Sent from my SM-G930W8 using Tapatalk

The picture makes the passenger hotspot look like it sits higher than the driverside.

I am well aware of LHD and RHD cutoffs. The LHD cut off looks like

____/ ____/

What I was saying is in the picture, the "horizontal line" looks like it's higher than the drivers side, like:

..........._____/
_____/

but like I said, it could just be the way the car was parked in relation to the house.

[Kaotic Lazagna]

That's what it should look like.

[Kaotic Lazagna]

But I just realized the door is actually not on the same plane as the garage, so that's why the passenger side appears to be higher than the driver side.

[IllusionX]

I started backing off and turning on a slanted driveway.

Sent from my SM-G930W8 using Tapatalk

[Yaris709]

How do I adjust the lights on my yaris sedan guys? The lights aren't aimed properly would like to get them aimed correctly

[Exiwolfman]

Originally Posted by Yaris709

How do I adjust the lights on my yaris sedan guys? The lights aren't aimed properly would like to get them aimed correctly

Adjust screw at top open hood

Sent from my SM-G935F using Tapatalk

[Kaotic Lazagna]

Originally Posted by Yaris709

How do I adjust the lights on my yaris sedan guys? The lights aren't aimed properly would like to get them aimed correctly

On the back of each headlight, iirc, there are metal adjustment knobs (it's hard to miss). I believe it's an 8mm to adjust.

[BennyLava]

Originally Posted by tmontague

Fwiw i only had condesation on one or m'y headlights after m'y original install when i tried reusing thé oem sealant. I then went To Lowes and bought à proper sealant that stays flexible and since then have had no issues in all types of weather and temperatures.

Imo if you don't want to deal with properly sealing them or the potential headache then don't do the mod, or pay for someone else to do it. Or like you did, manually point them down so they don't blind others - however this ends up leading to poor light patterns like you stated which brings me back to my previous point of do it properly or not at all

Do you have a thread where you took apart the Yaris headlight and installed the lenses? I don't want to blind anyone, but I want those LED's! I'm no stranger to DIY so hopefully I can just copy whatever you did. I have a 2009 sedan. I hope you don't lose any brightness and/or visibility by using a lens. But I have to have some kind of cuttoff for the beam where I am, because as far as I know its against the law to have lights that blind people and you will get pulled over for it.

[tarkus]

An informative article about halogens and HIDs - http://www.ebay.com/gds/Xenon-and-HI...1832221/g.html

[ryryAP2]

Originally Posted by Kaotic Lazagna

And if you don't want to take apart the headlights to do a projector retrofit (but can some how remove that shield/cover thing through the bulb opening), you can use these: https://www.amazon.com/Rover-Project...ini-projectors

I would have went with them, but they're built in HID bulbs, and are 6000k (wouldn't want anything more than 5000k unless they're Osram CBI). I wouldn't use anything less than Morimoto bulbs for HIDs, but that's just me.

Newbie here! Was wondering if anyone has tried these rover projector bulbs? Wanted to do a PnP without retrofitting projectors.

[Yaris874]

I got one different brand on ebay for 22 am goin to try to do it today may be

Sent from my SM-G935T using Tapatalk

[ryryAP2]

Originally Posted by Yaris874

I got one different brand on ebay for 22 am goin to try to do it today may be

Sent from my SM-G935T using Tapatalk

Awesome! Let me know how they work out. I'm thinking of pulling the trigger on the Amazon Car Rover ones. If anything they have a good return policy at Amazon

[Yaris874]

The ones on ebay ar not built in hid
So the Amazon are is the only difference

Sent from my SM-G935T using Tapatalk

[Yaris874]

But u still have to buy the ballast on the Amazon ones the ebay ones u buy ur Owen so u can pick ur color and 35w or 55w

Sent from my SM-G935T using Tapatalk

[ryryAP2]

Originally Posted by Yaris874

But u still have to buy the ballast on the Amazon ones the ebay ones u buy ur Owen so u can pick ur color and 35w or 55w

Sent from my SM-G935T using Tapatalk

From what I understand they only come with 6000k. Amazon sells a kit with the bulbs, ballasts ,and harness relay. The ballasts are 55w, but I was thinking of getting 35w. hmmmmmmm.

Here's the link: http://a.co/gysL9HO

[tarkus]

Originally Posted by Yaris874

I got one different brand on ebay for 22 am goin to try to do it today may be

Sent from my SM-G935T using Tapatalk

Can you share the eBay link?

Sent from my phone with Tapatalk. Please excuse any typpos.