|
04-23-2009, 11:20 AM | #127 | |
Drives: 2009 Yaris Hatchback Join Date: Feb 2009
Location: NJ
Posts: 792
|
Quote:
|
|
04-23-2009, 11:45 AM | #128 |
SIPNDEW
|
i just want to stress a point again. anyone who just did this mod you have to drive it for a good 2 days or so for the ecu to learn the now tb. it will oscillate bad until then.
|
04-23-2009, 12:01 PM | #129 |
Drives: 2009 Yaris Hatchback Join Date: Feb 2009
Location: NJ
Posts: 792
|
Oh I was under the impression that the chip swap made the oscillation and CEL go away immediately. Think I should leave it on for a few days?
|
04-23-2009, 12:48 PM | #130 |
toyota
Drives: 2007 Yaris RS Blazed Join Date: Oct 2006
Location: toronto, canada
Posts: 3,637
|
i guess time will tell
|
04-23-2009, 01:12 PM | #131 |
Yes....I would leave it on and see what happens.
|
|
04-23-2009, 02:38 PM | #132 | |
Drives: 2009 Yaris Hatchback Join Date: Feb 2009
Location: NJ
Posts: 792
|
Quote:
|
|
04-23-2009, 03:23 PM | #133 |
SIPNDEW
|
i did after the chip swap for a day or so. give it some time.
|
04-23-2009, 05:54 PM | #134 |
Drives: 2009 Yaris Hatchback Join Date: Feb 2009
Location: NJ
Posts: 792
|
|
04-23-2009, 07:33 PM | #135 |
SIPNDEW
|
:) mine still cold idles high for a min but it goes down to normal after that
|
04-23-2009, 08:08 PM | #136 |
Drives: 2008 yaris, stripped, red Join Date: Jan 2009
Location: SE Texas
Posts: 977
|
ok.......
here's the deal....again...for you who will listen now you can stop the oscillation in less than ten minutes. after the swap, pull the plug on the battery, drain caps by hitting brakes and turning on lights plug in batt start car AND LET IDLE FOR 10 MINUTES you have to re-learn the iac sensor to the new throttle body...it is oscilating to learn the position of the iac motor....unless you have a vac leak somewhere. |
04-23-2009, 08:35 PM | #137 | |
Drives: 2009 Yaris Hatchback Join Date: Feb 2009
Location: NJ
Posts: 792
|
Quote:
|
|
04-24-2009, 07:56 AM | #138 |
bx in the house
Drives: toyota yaris sedan Join Date: Oct 2008
Location: N.Y.
Posts: 113
|
quick ? guys what's the diameter on the 1zz tb is it 2" & half or 3"
|
04-24-2009, 07:59 AM | #139 |
Mine's on the car, so I can't really measure it right now.
Do a search. It's on here. I think in the Performance Mod section. There's a picture of both TBs and the exact measurement of each.
__________________
AEM CAI, NST Pulleys/SSK, WR 4-2-1 Header, TRD axelback, R1 Concept Rotors, TRD Sway Bar, Nitto Rear Strut Bar, Cusco GT-Zero Coilovers, 1ZZ-FE 1.8L TB |
|
04-24-2009, 08:35 AM | #140 |
bx in the house
Drives: toyota yaris sedan Join Date: Oct 2008
Location: N.Y.
Posts: 113
|
|
04-24-2009, 12:43 PM | #141 |
toyota
Drives: 2007 Yaris RS Blazed Join Date: Oct 2006
Location: toronto, canada
Posts: 3,637
|
been 2 days anyone got rid of the issue..
|
04-24-2009, 12:52 PM | #142 |
I never had the issue.
I think you have an air leak somewhere in the system. Best bet is to pull the TB, and reapply the sealer and let it sit overnight to set up. |
|
04-24-2009, 01:13 PM | #143 |
Drives: 2009 Yaris Hatchback Join Date: Feb 2009
Location: NJ
Posts: 792
|
|
04-26-2009, 02:24 PM | #144 |
toyota
Drives: 2007 Yaris RS Blazed Join Date: Oct 2006
Location: toronto, canada
Posts: 3,637
|
well................anyone.
|
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
1.8L Engine Swap, Possible? | Yaris T-Sport | Performance Modifications | 4 | 05-06-2007 06:57 PM |
swap for 2zz-ge???? | yarisTOONR82 | Performance Modifications | 12 | 03-23-2007 07:15 PM |