Toyota Yaris Forums - Ultimate Yaris Enthusiast Site
 

 


 
Go Back   Toyota Yaris Forums - Ultimate Yaris Enthusiast Site > Technical Forums > DIY / Maintenance / Service
  The Tire Rack

Reply
 
Thread Tools Display Modes
Old 10-14-2015, 02:35 PM   #1
Silverkarn
 
Drives: 2008 Toyota Yaris 2D
Join Date: Apr 2014
Location: United States
Posts: 28
Are there alternative jack stand spots? (08 Yaris)

2008 Yaris hatchback

I know where the jack points are in front and back for the floor jack, but i was wondering if there is anywhere else i can safely put jack stands without damaging anything besides the pinch welds behind the front tires and in front of the back tires.

All i have for jack stands are ones that have a VERY slightly curved bar at the top, I tried hockey pucks with a groove cut into them under the pinch welds, but the hockey puck started tilting off the stand as i slowly lowered the car down.
Silverkarn is offline   Reply With Quote
Old 10-24-2015, 11:55 PM   #2
billfires
 
Drives: 2010 3dr LB
Join Date: Sep 2010
Location: SE Mass
Posts: 89
When jacking my Yaris I use a 2"x8" board that allows me to lift the whole side at once. I would think you could do something similar when using jack stands. Bill C
billfires is offline   Reply With Quote
Old 10-25-2015, 11:10 AM   #3
ex-x-fire
 
Drives: 2010 yaris 3 door hatch
Join Date: Jun 2013
Location: Sheboygan Falls, Wi.
Posts: 451
I like to lift on the boxed section of the floor pan, sometimes called a subframe. This tread has some pictures for lifting the entire front or rear.
http://www.yarisworld.com/forums/showthread.php?t=9823
ex-x-fire is offline   Reply With Quote
Old 11-10-2015, 01:26 AM   #4
SirDigby
 
Drives: 2007 yaris 3 door
Join Date: Sep 2015
Location: Denver, Colorado
Posts: 998
yes that is good places. also you can jack on the subframe/body bolts, and the center uni-body rail/frame. if you look underneath you can see some rubber body plugs where the vehicle was mounted on the assembly like, this is also a support area.
SirDigby is offline   Reply With Quote
Old 11-10-2015, 07:33 AM   #5
tmontague
 
tmontague's Avatar
 
Drives: '08 2zr swapped Vios M/T
Join Date: Oct 2012
Location: Caledonia Ont.
Posts: 2,931
I finally got around to modifying modifying hockey push with an angle grinder. I'm lowered so I cannot aces the front lift point.

I usually jack my car up about twice a month so the pinch welds are not adequate for that.

I now lift at the pinch welds using a puck and then place my jack stands under my control arms for the front (, close to the subframe , possible). For the rear I place the axle on jack stands this way there is no weight on the pinch welds.

Worked well this past weekend with no issues.
__________________
No one ever wants to give a Yaris the point by...
tmontague is offline   Reply With Quote
Reply

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump

Similar Threads
Thread Thread Starter Forum Replies Last Post
How are you guys jacking up your Yaris? touroxin DIY / Maintenance / Service 65 02-01-2015 05:42 PM
What is it about the Yaris Ranger SVO General Yaris / Vitz Discussion 18 01-06-2015 10:45 PM
WTB: 2006-2008 Yaris Stereo Wiring Harnesses, AUX Jack zerosktz Willing to Buy by private party 4 02-19-2011 03:41 PM
NEWS: TOYOTA REVEALS ALL-NEW YARIS SEDAN AT 2006 LOS ANGELES AUTO SHOW VitzBoy General Yaris / Vitz Discussion 5 09-05-2010 09:53 PM
2007 Yaris Pricing Info ! YarisBueller New YARIS Purchase Forum 104 06-24-2009 05:54 PM


All times are GMT -4. The time now is 02:32 AM.




YarisWorld
Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2023, vBulletin Solutions Inc.