|
03-27-2009, 07:54 PM | #1 |
toyota
Drives: 2007 Yaris RS Blazed Join Date: Oct 2006
Location: toronto, canada
Posts: 3,637
|
MY new PRM Intake...
well i finally got it in.. got this from gerry creator of jetstream intake system..about a month ago but didnt have a chance to put it on till today..all due to toyota had to fix some idling issue that i had..the main reason i got this is to due local access and unique design..believe me this thing did not disappoint me once i saw it live...anyways here's my take on this..
*sleek design definitely original..talking about the reverse cone on the tube. *short ram cold air intake..gerry found a spot on that corner where for this intake to pull some cold air. proven after about an hour drive mid pipe remain cool to the touch but everything else is warm including the walls on the battery. *half usa made half canadian. rubber tubes and i believe oiled filter itself is made in usa and pipe and filter cover is canadian based. unfortunetely what they are made of only PRM can tell you.. *took about 25 minutes to install including unstalling stock box. final setup is sturdy no brackets needed the whole piece is held by the rubber tube at the end right by the intake manifold.. on the road: bare in mind i got k&n filter on stock box to compare this to. *took it to 85 km/hr playin between 2nd and 3rd gear. pull was great once i hit 3500revs and up.. *sound is not too far from my stock box w/ K&n filter on it although i dont have the tube running on the stock box. on the prm intake there is still an added rev noise once you stomp on the gas. *so far overall very happy with this intake..no need to reset ecu , no cel issue either , i had the rev drop to 450-500 rpm at the beginning on idle but after driving its back to normal. *just took this on the highway and all i can say is WOW!! the grunt and pick up is actually there..."brisky" is the word downshifting ,upshifting and all i can say is excellent choice of an intake no regrets... i guess the straight pipe helped a lot compare to stock box w/ K&n on it.. sound file inside the car.. http://www.youtube.com/watch?v=BdEe4sQ_u8E http://www.prmracing.com Last edited by marcus; 05-03-2009 at 09:24 AM. |
03-27-2009, 08:02 PM | #2 |
Drives: 06 Polar White 5dr, 13 Soul 4u Join Date: Oct 2008
Location: Georgetown, Ontario, Canada
Posts: 5,762
|
Do you notice any more pull off the line? I did with mine.
__________________
|
03-27-2009, 08:13 PM | #3 |
toyota
Drives: 2007 Yaris RS Blazed Join Date: Oct 2006
Location: toronto, canada
Posts: 3,637
|
ill try to notice it when i go out tonight.. i dont like gunning the car from stop.just not me... ill try it just for you though.. i dont mind pushing the car once its spinning..ill see what happen on my highway runs..
|
03-27-2009, 08:42 PM | #4 |
'07 to '12:2 wipers to 1?
Drives: '12 5-door LE & '14 5-door LE Join Date: Apr 2007
Location: Orlando
Posts: 1,999
|
is the price on the site CAD or USD?
either way...cripes...looks good though. I would hope it would come with some sort of bracket sometime...that silicone connector is going to fatigue no matter what and eventually give.
__________________
MicroImageonline forums - Shroomster Xda Forums - Shroomster Androidforums - Shroomster I'm noticing a pattern...... |
03-27-2009, 09:09 PM | #5 |
Carless in Chicago
|
eh, it really depends on how far the filter construction goes into the connector and how heavy the filter portion is. the connector could also be quite rigid. it's hard to say what exactly will happen over time.
__________________
Wanted: Forced Induction Some say that he is the secret love child of Ferrari and Porsche, and others say that he would lap James May twice in a 1/4 mile drag race. All we know is that he is called The Stig. |
03-27-2009, 09:27 PM | #6 | |
Drives: 06 Polar White 5dr, 13 Soul 4u Join Date: Oct 2008
Location: Georgetown, Ontario, Canada
Posts: 5,762
|
Quote:
The entire unit is very light, and if you watch the video, I'd be more concerned about a mounting bracket causing the connector to pull away from the throttle body as the intakes movement would be restricted. Without a mounting bracket, the unit is allowed to move freely with the engine. http://www.youtube.com/watch?v=kQofIM1wJI0
__________________
Last edited by WeeYari; 03-27-2009 at 09:57 PM. |
|
03-27-2009, 09:53 PM | #7 |
toyota
Drives: 2007 Yaris RS Blazed Join Date: Oct 2006
Location: toronto, canada
Posts: 3,637
|
ill check on this to make sure so far i had it ultra tight..
|
03-27-2009, 11:18 PM | #8 | ||
'07 to '12:2 wipers to 1?
Drives: '12 5-door LE & '14 5-door LE Join Date: Apr 2007
Location: Orlando
Posts: 1,999
|
Quote:
Quote:
you wouldn't have to worry about the maf moving at all or fatigue at all; but like I said fatigue will set in sooner than later because the silicone is what is holding the intake in the position it is in. example I can think of is you're holding a balloon by the place you blow air into it. Your hand is the engine and the balloon is the intake....keep your hand still on a windy day and watch the balloon move around everywhere. by the way I'm not opposed to the intake at all I'm just providing my constructive criticism and I'm not trying to be negative at all (after all you can't 'read' text)
__________________
MicroImageonline forums - Shroomster Xda Forums - Shroomster Androidforums - Shroomster I'm noticing a pattern...... |
||
03-28-2009, 12:17 AM | #9 |
Drives: Yaris Hatch /Landrover D2 Join Date: Jun 2007
Location: Canada
Posts: 242
|
I like the built in velocity stack to smooth incomming air.
|
03-28-2009, 12:17 PM | #10 |
toyota
Drives: 2007 Yaris RS Blazed Join Date: Oct 2006
Location: toronto, canada
Posts: 3,637
|
wicked highway run today..although i would like for you guys to hear it so ill try to do another run today with a friend to take a video while i push this beast to the limit.
i did notice a difference on the off the line pull on this weeyari.. its a great product and no regrets...and i did run a wire across the bay for the filter to lean on too incase its putting pressure on the silicone tube worked out great.. |
03-28-2009, 01:56 PM | #11 |
Drives: 06 Polar White 5dr, 13 Soul 4u Join Date: Oct 2008
Location: Georgetown, Ontario, Canada
Posts: 5,762
|
I've been running 5 months without providing any extra support. Frankly, when I look at the sturdiness of the connector and the light weight, I'm not concerned about the connection.
__________________
|
03-28-2009, 02:51 PM | #12 |
toyota
Drives: 2007 Yaris RS Blazed Join Date: Oct 2006
Location: toronto, canada
Posts: 3,637
|
now the exhaust..really want to get one fr garm..but i cant decide if im gonna go with noise again while driving which i do kinna missed on my prev car but quiet ride is great as well.. i must be getting old...
|
03-29-2009, 12:30 AM | #13 |
Drives: Yaris Liftback 2008 Join Date: Mar 2009
Location: SoCal
Posts: 15
|
Have you noticed any change in gas mileage?
|
03-29-2009, 03:02 AM | #14 |
toyota
Drives: 2007 Yaris RS Blazed Join Date: Oct 2006
Location: toronto, canada
Posts: 3,637
|
|
03-30-2009, 12:29 PM | #15 |
Drives: supra Join Date: Oct 2008
Location: toronto
Posts: 10
|
$
there is a introductory group buy price happening right know
@ $200.00 shipped. if your interested contact Gerry e-mail prm@look.ca www.prmracing.com or PM me. |
03-30-2009, 03:49 PM | #16 |
toyota
Drives: 2007 Yaris RS Blazed Join Date: Oct 2006
Location: toronto, canada
Posts: 3,637
|
thanks gerry great design on the intake..one of a kind.
|
04-01-2009, 06:19 PM | #17 |
Drives: 06 Polar White 5dr, 13 Soul 4u Join Date: Oct 2008
Location: Georgetown, Ontario, Canada
Posts: 5,762
|
Decided that my (dirty) engine bay needed a splash of colour. Went and saw Gerry last weekend to swap my black silicones for red.
__________________
|
04-01-2009, 06:23 PM | #18 |
toyota
Drives: 2007 Yaris RS Blazed Join Date: Oct 2006
Location: toronto, canada
Posts: 3,637
|
nice....and i do love this intake makes acceleration briskier.. i push the car on highway 401 everytime i head home..i just love the sound i got to post a video so everyone can hear..
oh by the way you can change the angle on where this thing is pointing depends on you preference..just turn the intake clock or counterclockwise. |
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
DIY: Intake Installation | redyaris | DIY / Maintenance / Service | 53 | 08-23-2014 05:34 AM |
Bomz Ebay Intake - Partial Review | Split | Performance Modifications | 11 | 11-19-2008 02:12 AM |
Intake Systems Decision Maker.. | Blenjar | Performance Modifications | 25 | 09-15-2007 10:07 PM |
WR Secret Weapon Intake Dyno Tested.. | WRLEO | Performance Modifications | 70 | 05-17-2007 03:00 PM |
Intake VS modified filter housing | Spades | Performance Modifications | 19 | 03-30-2007 12:30 AM |