Toyota Yaris Forums - Ultimate Yaris Enthusiast Site
 

 


 
Go Back   Toyota Yaris Forums - Ultimate Yaris Enthusiast Site > Technical Forums > DIY / Maintenance / Service
  The Tire Rack

Reply
 
Thread Tools Display Modes
Old 06-17-2022, 05:42 PM   #1
esse10
 
Drives: 2009 yaris 2 door
Join Date: Feb 2013
Location: richmond TX.
Posts: 212
clutch replacement, 2009 1.5L

who here has already replaced their clutch themselves and can give me a few tips on that? is there a procedure to adjusting the shift cable links/ends after re-install? anybody know the tranny mount torque values?

thanks folks
esse10 is offline   Reply With Quote
Old 06-21-2022, 10:05 AM   #2
esse10
 
Drives: 2009 yaris 2 door
Join Date: Feb 2013
Location: richmond TX.
Posts: 212
clutch

Fellas? i thought people worked on their cars around here. Nobody has actually adjusted their shifting links before on these cars.....HHHMM???
esse10 is offline   Reply With Quote
Old 06-24-2022, 01:07 PM   #3
remcafee
 
Drives: 2007 Toyota Yaris 3 door
Join Date: Sep 2018
Location: Arizona
Posts: 186
the clutch is fairly easy to do on our cars, the one thing to keep in mind is putting on red loctite on flywheel bolts and torquing them down the spec properly, they are 38 ft ibs, and a 90 degree turn in a star pattern, your rear subframe torque mount bolt is going to be 89 ft ibs.
remcafee is offline   Reply With Quote
Old 06-30-2022, 07:45 AM   #4
esse10
 
Drives: 2009 yaris 2 door
Join Date: Feb 2013
Location: richmond TX.
Posts: 212
clutch

Quote:
Originally Posted by remcafee View Post
the clutch is fairly easy to do on our cars, the one thing to keep in mind is putting on red loctite on flywheel bolts and torquing them down the spec properly, they are 38 ft ibs, and a 90 degree turn in a star pattern, your rear subframe torque mount bolt is going to be 89 ft ibs.
I didn't mess with the flywheel bolts i just replaced the clutch, pressure plate and throw out bearing. I didn't remove the subframe either just manhandle the tranny in there it's not that heavy.
esse10 is offline   Reply With Quote
Old 07-03-2022, 10:15 PM   #5
remcafee
 
Drives: 2007 Toyota Yaris 3 door
Join Date: Sep 2018
Location: Arizona
Posts: 186
you should of machined the flywheel or replaced it, youre going to get chatter when using the clutch soon, the vibration is bad as it is also making sure the crankshaft is spinning smooth, now there is going to be more vibration and the wear on crankshaft will accelerate
remcafee is offline   Reply With Quote
Old 07-04-2022, 12:29 PM   #6
sh0rtlife
 
Drives: 2007 5dr canadian import
Join Date: Dec 2016
Location: pacific north WET
Posts: 202
or youll heat glaze the snot out of the clutch and trash it in short order....machining the flywheel for a clutch swap is a MUST otherwise you can be 110% sure of shortened clutch life by atleast half
sh0rtlife is offline   Reply With Quote
Old 07-04-2022, 01:36 PM   #7
esse10
 
Drives: 2009 yaris 2 door
Join Date: Feb 2013
Location: richmond TX.
Posts: 212
Tranny clutch

Does the transmission go out a lot on these cars? I mean the inside bearing go bad after certain amount of miles?
Mine is making a rattling noise that seems to be coming from the tranny output bearing. I'm gonna have it refurbished or replace it with a used one, if I can find one
esse10 is offline   Reply With Quote
Reply

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump

Similar Threads
Thread Thread Starter Forum Replies Last Post
Clutch Maintenance fnkngrv DIY / Maintenance / Service 12 03-03-2017 10:42 AM


All times are GMT -4. The time now is 08:53 AM.




YarisWorld
Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2022, vBulletin Solutions Inc.