CTScott.. broken parts - Toyota Yaris Forums

Eduardo_mty · 11-09-2014, 08:08 PM

CTScott, do you have this part? 82819-0D070

i searching on the internet and i cant found it

CTScott · 11-09-2014, 08:17 PM

That part is actually just considered part of the hatch wiring harness, so you can't purchase it separately from Toyota. I had one but sold it a while back to someone who did the same kind of damage to his.

Eduardo_mty · 11-09-2014, 08:29 PM

Thank you.... Its the same for others years, to search on yunkyards here in México

CTScott · 11-09-2014, 08:45 PM

Quote:

Originally Posted by Eduardo_mty

Thank you.... Its the same for others years, to search on yunkyards here in México

That looks identical to 2nd generation ones, so you should be able to use one from 2006 to present.

And, it is easiest to remove it without damage by squeezing it from below (getting above the head liner).

Eduardo_mty · 11-11-2014, 12:59 PM

Ctscott, this part have a name, i try to ask on Internet yunkyards.

Here in México i can't found it

CTScott · 11-11-2014, 02:49 PM

Quote:

Originally Posted by Eduardo_mty

Ctscott, this part have a name, i try to ask on Internet yunkyards.

Here in México i can't found it

I have never seen a definite name for the white part, but I would inquire about the hatch wiring harness, as it is part of that assembly.

Eduardo_mty · 11-12-2014, 03:22 PM

$ 50 usd for this part, is good price... i found one in mexico

Eduardo_mty · 11-14-2014, 12:17 PM

How i will install the White piece

joell · 11-14-2014, 12:36 PM

Isn´t a two piece part like mine (third gen hatchback), looks like you will need to remove the wiring before inserting in the body of the car.Search for diagrams that can give you a better idea.

CTScott · 11-14-2014, 01:01 PM

If I remember correctly the connector ends fit through the white piece, but it has been a while since I had one in my hands.

ucsmfu · 12-11-2014, 02:14 PM

won't the wire fit through this plastic part ?

Eduardo_mty · 12-11-2014, 02:19 PM

When i did that, i dont know how to remove, i pull from "outside" to inside and broken that piece

Eduardo_mty · 12-11-2014, 02:25 PM

Look

Eduardo_mty · 12-11-2014, 02:27 PM

You need to remove a little ceiling to remove this White plastic

ucsmfu · 12-11-2014, 03:38 PM

i was able to feed both wires through the plastic piece. I didn't need to remove it.

My question now is how do I put the black grommet back in place ? The bottom part of the grommet which goes over the plastic part.

Thanks

CTScott · 12-11-2014, 06:31 PM

Quote:

Originally Posted by ucsmfu

i was able to feed both wires through the plastic piece. I didn't need to remove it.

My question now is how do I put the black grommet back in place ? The bottom part of the grommet which goes over the plastic part.

Thanks

You have to remove the white part to get the black part back over it correctly.

ucsmfu · 12-11-2014, 09:27 PM

Quote:

Originally Posted by CTScott

You have to remove the white part to get the black part back over it correctly.

what's the best way of removing it properly ?

thanks

CTScott · 12-11-2014, 09:32 PM

Quote:

Originally Posted by ucsmfu

what's the best way of removing it properly ?

thanks

Pull the rear part of the headliner and release it from below.

11-09-2014, 08:17 PM	#2
CTScott ULTIMATE View User's Garage Drives: 09 5dr LB, 2x 08 3dr LB Join Date: Oct 2008 Location: USA, CT Posts: 13,460	That part is actually just considered part of the hatch wiring harness, so you can't purchase it separately from Toyota. I had one but sold it a while back to someone who did the same kind of damage to his. __________________

11-14-2014, 01:01 PM	#10
CTScott ULTIMATE View User's Garage Drives: 09 5dr LB, 2x 08 3dr LB Join Date: Oct 2008 Location: USA, CT Posts: 13,460	If I remember correctly the connector ends fit through the white piece, but it has been a while since I had one in my hands. __________________

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
Have you noticed that parts are hard to find for the Yaris?	grampi	DIY / Maintenance / Service	2	09-06-2014 12:42 PM
broken blitz supercharger needed for parts, for 1nz-fe	biffy	Willing to Buy by private party	13	02-10-2014 03:28 PM
Yaris Super trip to buy aftermarket parts / 1500miles (2547km) in 36hrs / Pictures	3cyltrbo	General Yaris / Vitz Discussion	10	11-07-2012 09:09 AM

11-09-2014, 08:29 PM	#3
Eduardo_mty Join Date: Sep 2014 Posts: 198	Thank you.... Its the same for others years, to search on yunkyards here in México

11-11-2014, 12:59 PM	#5
Eduardo_mty Join Date: Sep 2014 Posts: 198	Ctscott, this part have a name, i try to ask on Internet yunkyards. Here in México i can't found it

11-12-2014, 03:22 PM	#7
Eduardo_mty Join Date: Sep 2014 Posts: 198	$ 50 usd for this part, is good price... i found one in mexico

11-14-2014, 12:17 PM	#8
Eduardo_mty Join Date: Sep 2014 Posts: 198	How i will install the White piece

11-14-2014, 12:36 PM	#9
joell Drives: 2013 Hatchback Join Date: Dec 2012 Location: Panama, Central America Posts: 57	Isn´t a two piece part like mine (third gen hatchback), looks like you will need to remove the wiring before inserting in the body of the car.Search for diagrams that can give you a better idea.

12-11-2014, 02:14 PM	#11
ucsmfu Drives: yaris le Join Date: Sep 2014 Location: vancouver, BC Posts: 224	won't the wire fit through this plastic part ?

12-11-2014, 02:19 PM	#12
Eduardo_mty Join Date: Sep 2014 Posts: 198	When i did that, i dont know how to remove, i pull from "outside" to inside and broken that piece

12-11-2014, 02:27 PM	#14
Eduardo_mty Join Date: Sep 2014 Posts: 198	You need to remove a little ceiling to remove this White plastic

12-11-2014, 03:38 PM	#15
ucsmfu Drives: yaris le Join Date: Sep 2014 Location: vancouver, BC Posts: 224	i was able to feed both wires through the plastic piece. I didn't need to remove it. My question now is how do I put the black grommet back in place ? The bottom part of the grommet which goes over the plastic part. Thanks