Toyota Yaris Forums - Ultimate Yaris Enthusiast Site
 

 


 
Go Back   Toyota Yaris Forums - Ultimate Yaris Enthusiast Site > Technical Forums > DIY / Maintenance / Service
  The Tire Rack

Reply
 
Thread Tools Display Modes
Old 10-28-2021, 07:43 PM   #1
PinkPumba
 
Drives: 2010 Toyota Yaris 3D LB
Join Date: Oct 2021
Location: Bethlehem, PA
Posts: 2
Question Roof Drip Molding replacement on 2010 3D LB

I'm trying to replace the LH and RH roof drip moldings on my 2010 Yaris 3D LB.

I purchased (2x) of 75551-52130 (same part used on both sides).
https://parts.toyota.com/p/Toyota__/...555152130.html

The LH molding went in fine but I can't get the RH molding to sit flat, it keeps lifting off the roof in the middle after I press it down.

Anyone else have struggles like this? I might just glue it down and be down with it :) or maybe try swapping the new LH and RH parts to see if that works.

The old RH molding didn't sit flat either and was bouncing/vibrating on the highway which is why I purchased a new one. Maybe the gap/flush is off on my Yaris from factory or from a previous owner accident.

Installation for reference (sedan but basically the same thing):
https://www.youtube.com/watch?v=TM_z...nel=burrheadjr

Thanks!
PinkPumba is offline   Reply With Quote
Old 10-28-2021, 08:37 PM   #2
CrankyOldMan
2ZR swap. DO IT! Ask how!
 
CrankyOldMan's Avatar
 
Drives: 09 Meteoric Metallic HB
Join Date: Feb 2011
Location: West Michigan
Posts: 2,332
You might have to replace the clips that hold them in. They're attached with some adhesive/tape, iirc. I bought them but never installed them and just removed the failing moldings. They're just cosmetic to cover the weld seams, right?
CrankyOldMan is offline   Reply With Quote
Old 11-13-2021, 01:02 PM   #3
PinkPumba
 
Drives: 2010 Toyota Yaris 3D LB
Join Date: Oct 2021
Location: Bethlehem, PA
Posts: 2
Thanks for the suggestion! However, my clips looked fine and the ends of the trim clipped in nicely.

I worked the trim with my hands to straighten it out more and used a heat gun when installing it again. The trim went in better (still kinda loose in the middle) but it doesn't vibrate while driving so I'm happy with how it is. If it does come loose I'll drop some Sikaflex-221 under the trim.

I think the trim also helps prevent water from pooling at the weld seams and causing rust over time.
PinkPumba is offline   Reply With Quote
Reply

Tags
2010, drip, molding, roof

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump

Similar Threads
Thread Thread Starter Forum Replies Last Post
Roof drip molding patm Cosmetic Modifications (Exterior/Interior) 6 01-11-2017 09:55 PM
Roof drip molding moving romram Cosmetic Modifications (Exterior/Interior) 9 04-01-2015 07:29 PM
Roof drip molding patm DIY / Maintenance / Service 1 05-20-2013 12:31 PM
Get your post counts here! *read 1st post for rules* Astroman Off-topic / Other Cars / Everything else Discussions 3414 11-04-2012 10:03 AM


All times are GMT -4. The time now is 02:17 PM.




YarisWorld
Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2021, vBulletin Solutions Inc.