Log in

View Full Version : Antho's turbo thread!

packetrace
08-24-2012, 08:37 PM
So some may have read my thread on MI but I wanted to share it here...

So far I have...

SR20DET T25 turbo
1NZ-FE engine
TOGA maine and rod bearing
CP piston 9:1
Highbeam rods
Goldean eagle fuel rail
2AZ-FE injertors
2.5'' intercooler piping kit
ebay CAI for the piping parts to make the piping easier
6AN fuel line with return with 255LPH pump
10an return oil lin
10 an water line
4 an oil feed line

What I am planning for the rest..
AEM GAUGE(thru-boost, water temp, oil pressure from a guy here on YW)
Malibuguy complete exhaust...
Timing chain cover and valve cover powdercoated from TBR with their brand new water pump
TBR complete pulley set
Intake manifold with xB cable TB
MI stainless manifold with heat wrap
Used Tial F38mm external WG
All stainless stud
new thermostat
new dip stick
New gasket(all)

Propably a manual tranny swap...because I am automatic


here are some picture of next component and actual engine

The car!!! But noew has no japanese sticker...
http://i1199.photobucket.com/albums/aa471/Antho_Paquette/1e99420d.jpg
Engine now..
http://i1199.photobucket.com/albums/aa471/Antho_Paquette/a4b359d9.jpg
http://i1199.photobucket.com/albums/aa471/Antho_Paquette/d3d5a0de.jpg
Gauge hole
http://i1199.photobucket.com/albums/aa471/Antho_Paquette/de58ffdb.jpg
The car in the garage
http://i1199.photobucket.com/albums/aa471/Antho_Paquette/88cde3cf.jpg
Fuel rail with TBR extra free fitting and hose that he sent me with this nice fuel rail black powder coated
http://i1199.photobucket.com/albums/aa471/Antho_Paquette/5E76951D-E586-4068-AC47-05AA54085636-5181-000005C4A8B4D92F.jpg
http://i1199.photobucket.com/albums/aa471/Antho_Paquette/8EB64D1D-807D-4355-9F87-41272989F889-5181-000005C4AEC83638.jpg
Painted engine
http://i1199.photobucket.com/albums/aa471/Antho_Paquette/b825123b.jpg
TBR soon complete pulley set
http://i1199.photobucket.com/albums/aa471/Antho_Paquette/536EC89A-0A87-4A81-B9B6-EC815D76A53B-5181-000005C4CFB6EDD4.jpg
pimp my yaris
08-26-2012, 10:17 PM
Thats a big project to do all at once. Good luck
thefalls
08-27-2012, 08:35 AM
This is very tempting. Every time i see someone with a forged build i feel like taking the plunge. But i constantly remind myself that its my daily drive :P

Keep up the good work.

PS: Going overbore or stock bore?
packetrace
08-27-2012, 08:45 AM
Thats a big project to do all at once. Good luck

Well the engine has already been running with a turbo...and has been tested on an engine bench test...so this part is no big deal

The rest is just some small stuff to had..

Pulleys new manifold new stud..install gauge...fuel rail....

Powdercoating all lolll

Engine management will be wired before so it makes easier the install
packetrace
08-27-2012, 08:46 AM
This is very tempting. Every time i see someone with a forged build i feel like taking the plunge. But i constantly remind myself that its my daily drive :P

Keep up the good work.

PS: Going overbore or stock bore?



You really should do it bro!!
thefalls
08-27-2012, 02:14 PM
Too early :) engine has only 45k kms. But i have been eyeing that pt tuning short block for a while. If shipping is reasonable then maybe i will splash out.
Yoda
08-27-2012, 03:22 PM
Too early :) engine has only 45k kms. But i have been eyeing that pt tuning short block for a while. If shipping is reasonable then maybe i will splash out.
^^ Great idea! Wish I went that route :frown:
packetrace
08-27-2012, 05:35 PM
Too early :) engine has only 45k kms. But i have been eyeing that pt tuning short block for a while. If shipping is reasonable then maybe i will splash out.

what you mean pt tuning ? got a link ?


When turbo is done I want to build a second engine....but this time...build it my self since this one was bought already built and fuly tested....

I do all that mostly to learn and have fun....it became a passion like 2-3 years ago...

Will pick up a 50k engine...sleeve it...forged pistons and rods...new bearing....new all :D loll

and try a big turbo...with a manual tranny echo ! I really want to try these small car :) Mine is a sedan...
thefalls
08-28-2012, 05:56 AM
http://www.ptuning.com/subdir/itemdetail.cfm?PartNo=PTP-ENG-12000&MakeCode=scion&ModelCode=xB&ModelYear=2004-2007%20All&ModelDesc=xB

There you go.

We dont have any workshop which can balance the rotating assembly here. So in future i will just get the short block. Works better this way.
Not too sure what to do about keeping a 8k rev limit.Some use the yaris cup springs.
Need to research a bit on this.
cali yaris
08-28-2012, 01:12 PM
PT tuning, I've only heard really good things about them. We can also build short blocks for West Coasters...
packetrace
08-28-2012, 05:28 PM
http://www.ptuning.com/subdir/itemdetail.cfm?PartNo=PTP-ENG-12000&MakeCode=scion&ModelCode=xB&ModelYear=2004-2007%20All&ModelDesc=xB

There you go.

We dont have any workshop which can balance the rotating assembly here. So in future i will just get the short block. Works better this way.
Not too sure what to do about keeping a 8k rev limit.Some use the yaris cup springs.
Need to research a bit on this.

sounds good....the only thing I dont like is shipping the block to USA from CANADA...where I live...

I really would like to try to build it on my own but its a risky job.....Ill finish turbo first...and see after :biggrin:
packetrace
08-28-2012, 05:28 PM
PT tuning, I've only heard really good things about them. We can also build short blocks for West Coasters...

good to know:thumbsup:
thefalls
08-29-2012, 02:43 PM
Indeed this is good news!
packetrace
08-30-2012, 07:43 AM
WG flange and gasket ordered*

Manifold from Alex1987 bought

SR20DET turbo from Alez1987 bought

Bought some nice Prosport gauge...thanks to Garm for pointing me these!!

here they are:
http://prosportgauges.com/images/products/detail/EvoWebsitepicBOOSTcopy.jpg
http://prosportgauges.com/images/products/detail/EvoWebsitepicOILPRESSURE.jpg
http://prosportgauges.com/images/products/detail/EvoWebsitepicWATERTEMP.jpg
Yoda
08-30-2012, 01:06 PM
well thats pretty. O and got your pm thanks!