DIY - 1.8L 1ZZ-FE TB Connector Chip Swap - Page 7 - Toyota Yaris Forums

marcus · 04-21-2009, 06:38 PM

WOULD THIS WORK FOR CANADIAN TB 1.5,...well im assuming it will.i may try this out...

AlexNet0 · 04-21-2009, 06:41 PM

Quote:

Originally Posted by marcus

WOULD THIS WORK FOR CANADIAN TB 1.5,...well im assuming it will.i may try this out...

as long as the stock is a 1nz-fe engine

marcus · 04-21-2009, 06:47 PM

aight..i guess i got a new project to do...

AlexNet0 · 04-21-2009, 08:15 PM

^no, not unless you also capped the hoses.

MGargano · 04-21-2009, 08:17 PM

Quote:

Originally Posted by AlexNet0

^no, not unless you also capped the hoses.

lol no I used one of those barb couplers. I finally broke down and did the chip swap and coolant bypass. I have the gasket maker setting overnight and look forward to testing it out tomorrow morning.

*tk-421* · 04-22-2009, 01:41 AM

Quote:

Originally Posted by MGargano

lol no I used one of those barb couplers. I finally broke down and did the chip swap and coolant bypass. I have the gasket maker setting overnight and look forward to testing it out tomorrow morning.

Good luck! Hope that gets that problem solved on your end.

I'm also considering capping the (now useless) tubes... What did you use for that?

MGargano · 04-22-2009, 10:06 AM

Quote:

Originally Posted by tk-421

Good luck! Hope that gets that problem solved on your end.

I'm also considering capping the (now useless) tubes... What did you use for that?

Just a few inches of rubber tubing with a little brass plug on the end. I found the plug's at Lowe's in the same section as the barb union coupler.

t0m4s · 04-22-2009, 02:09 PM

did everybody trim the OEM TB gasket to allow more air flow as t-sport did?

MGargano · 04-22-2009, 04:58 PM

No good so far. Oscillation is way worse at cold start up than before the chip swap and I got a CEL within 10 minutes of driving :(

marcus · 04-22-2009, 05:28 PM

Quote:

Originally Posted by MGargano

No good so far. Oscillation is way worse at cold start up than before the chip swap and I got a CEL within 10 minutes of driving :(

darn it!!

jkuchta · 04-22-2009, 06:39 PM

I'm still getting 37-38mpg per tank with the 1ZZ TB...and I've had it on for nearly 1000 miles so far.

MGargano · 04-23-2009, 12:24 AM

Unless someone can convince me otherwise, I'm putting the stock TB back on tomorrow. I can handle the CEL but the oscillation is a little scary. After the chip swap, it oscillates very heavily from 2k to 3k for almost 2 minutes.

Yaris T-Sport. · 04-23-2009, 02:40 AM

Quote:

Originally Posted by MGargano

Unless someone can convince me otherwise, I'm putting the stock TB back on tomorrow. I can handle the CEL but the oscillation is a little scary. After the chip swap, it oscillates very heavily from 2k to 3k for almost 2 minutes.

do this, put the stock TB back and drive it for over a week with out doing and or trying anything at all and then swap the chip back to 1zz and try it again, this helps your ecu to remember the normal setup, then give it a fresh try after that. it worked for me.

yarstar · 04-23-2009, 07:40 AM

I concur with T-Sport. Giving it a 2nd try made it work for me too.

35-38 mpg now for 3k miles with new TB. No issues at all, except high cold idle. I really think it's worth it.

MGargano · 04-23-2009, 10:25 AM

I love the performance of the 1ZZ but the harsh oscillation is a killer. So I should reinstall the stock TB & chip for a week or so and then start over with the 1ZZ and chip swap?

yarstar · 04-23-2009, 11:19 AM

Quote:

Originally Posted by MGargano

I love the performance of the 1ZZ but the harsh oscillation is a killer. So I should reinstall the stock TB & chip for a week or so and then start over with the 1ZZ and chip swap?

That worked for me. You may be getting ocillation due to an air leak. Make sure you did the gasket maker correctly and really let it set up a long time (I let mine set up overnight). Check also the intake for leaks.

I pulled mine back off, waited a week, did the chip swap again, and re-installed and have had no probs since.

MGargano · 04-23-2009, 11:20 AM

Quote:

Originally Posted by yarstar

That worked for me. You may be getting oscillation due to an air leak. Make sure you did the gasket maker correctly and really let it set up a long time (I let mine set up overnight). Check also the intake for leaks.

I pulled mine back off, waited a week, did the chip swap again, and re-installed and have had no probs since.

Thanks. I'll give that a try.

MGargano · 04-23-2009, 02:38 PM

Quote:

Originally Posted by yarstar

That worked for me. You may be getting ocillation due to an air leak. Make sure you did the gasket maker correctly and really let it set up a long time (I let mine set up overnight). Check also the intake for leaks.

I pulled mine back off, waited a week, did the chip swap again, and re-installed and have had no probs since.

Did you get CEL and oscillation the first time you did the chip swap?

04-21-2009, 08:15 PM	#4
AlexNet0 View User's Garage Drives: '07 Yaris 3dr Join Date: Nov 2008 Location: Rockland, ME Posts: 1,638	^no, not unless you also capped the hoses. __________________ ---------- MI-YW ----------

04-22-2009, 02:09 PM	#8
t0m4s 1NZ-FE View User's Garage Drives: Yaris Seddan 08 Join Date: Oct 2008 Location: Panama Posts: 220	did everybody trim the OEM TB gasket to allow more air flow as t-sport did? __________________ . DC Sports Header, Vibrant Hi-Flow Cat, Round Magnaflow Muffler, Vibrant Tip, Dunlop Direzza 195/50 Rims 15", Injen Technologies Cold Air Intake, NST CR-Lite crank, waterpump & alternator pulleys, Tanabe NF210 Springs, NST SSK 1 & 2, NST Shifter Cable & Cage Bushing Kit, Nitto Engine Torque Damper

04-23-2009, 07:40 AM	#14
yarstar View User's Garage Drives: 2008 Absolute Red HB Join Date: Oct 2008 Location: Georgia Posts: 264	I concur with T-Sport. Giving it a 2nd try made it work for me too. 35-38 mpg now for 3k miles with new TB. No issues at all, except high cold idle. I really think it's worth it. __________________ AEM CAI, NST Pulleys/SSK, WR 4-2-1 Header, TRD axelback, R1 Concept Rotors, TRD Sway Bar, Nitto Rear Strut Bar, Cusco GT-Zero Coilovers, 1ZZ-FE 1.8L TB

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
1.8L Engine Swap, Possible?	Yaris T-Sport	Performance Modifications	4	05-06-2007 06:57 PM
swap for 2zz-ge????	yarisTOONR82	Performance Modifications	12	03-23-2007 07:15 PM

04-21-2009, 06:38 PM	#1
marcus toyota View User's Garage Drives: 2007 Yaris RS Blazed Join Date: Oct 2006 Location: toronto, canada Posts: 3,637	WOULD THIS WORK FOR CANADIAN TB 1.5,...well im assuming it will.i may try this out...

04-21-2009, 06:47 PM	#3
marcus toyota View User's Garage Drives: 2007 Yaris RS Blazed Join Date: Oct 2006 Location: toronto, canada Posts: 3,637	aight..i guess i got a new project to do...

04-22-2009, 04:58 PM	#9
MGargano Drives: 2009 Yaris Hatchback Join Date: Feb 2009 Location: NJ Posts: 792	No good so far. Oscillation is way worse at cold start up than before the chip swap and I got a CEL within 10 minutes of driving :(

04-22-2009, 06:39 PM	#11
jkuchta View User's Garage Drives: 2007 Yaris hatch (red) Join Date: Sep 2007 Location: L.A. Posts: 557	I'm still getting 37-38mpg per tank with the 1ZZ TB...and I've had it on for nearly 1000 miles so far.

04-23-2009, 12:24 AM	#12
MGargano Drives: 2009 Yaris Hatchback Join Date: Feb 2009 Location: NJ Posts: 792	Unless someone can convince me otherwise, I'm putting the stock TB back on tomorrow. I can handle the CEL but the oscillation is a little scary. After the chip swap, it oscillates very heavily from 2k to 3k for almost 2 minutes.

04-23-2009, 10:25 AM	#15
MGargano Drives: 2009 Yaris Hatchback Join Date: Feb 2009 Location: NJ Posts: 792	I love the performance of the 1ZZ but the harsh oscillation is a killer. So I should reinstall the stock TB & chip for a week or so and then start over with the 1ZZ and chip swap?