"Parmas" Motor

[Parmas]

I am making an estimate of all things I need...... I wish anyone who can help to post some useful info.

The tuner gave me this estimate of parts to replace\upgrade:
Parts marked are thought to be left out

- Toyota OE Overall Gasket Set
- Toyota OE Crank shaft Bearings Kit
- Toyota OE Trust Bearings
- Toyota OE Timing chain kit ?

- Arias Rings Set - Where to buy? Prices ?
- Block Guard Custom made ? What about sleeves? Cost? Need new pistons?
- Steel Head Studs - Thinking of AJUSA or ARP. Where To buy?
- Knife edge crankshaft ?
- Full bottom end Balancing
- Flywheel Lightening + faces ?
- Head Porting - There are different stages, can anyone explain in detail?
- Cometic MLS Head Gasket - Does AJUSA have better head gaskets?

If I am missing something please post reply...

[cali yaris]

I'm running a stock head gasket, no problems at all and you know my motor. What head studs are you using?

see post 257 about the block guard.

[Parmas]

Originally Posted by cali yaris

I'm running a stock head gasket, no problems at all and you know my motor. What head studs are you using?

see post 257 about the block guard.

Head studs are the same it came with the engine which are probably stock ones.

I read the post 257 but I don't know where I can find for our 1NZ. Also what kind of issues I might get into if using the same pistons?

Garm I would appreciate any comments on the other parts mentioned aswell. Which in your opinion I might need or not...

[cali yaris]

stock head studs are not a good idea. We had to custom make a set, but there is a company overseas making them. Can't vouch for the quality though.

[Parmas]

Originally Posted by cali yaris

there is a company overseas making them. Can't vouch for the quality though.

What company are you referring to?

[cali yaris]

http://www.microimageonline.com/foru...lts-yaris.html

You posted that the link doesn't work for you, but I just tried it and it came up ok.

[yaris-me]

Originally Posted by Parmas

The problem is probably a valve because if it was a piston ring the breather will show a considerable amount of oil coming out.

Finally the good news is that the authorities confirmed that there is no expense to change the engine (an amount that was thought to be near $2000). So now with these money I am going to fix the compression problem, port & polish head, lighten flywheel?, new seals and maybe a block guard.

Is there a brand that makes sales of a block guard for our 1NZ? Do you have for sale garm?

If valves get moved around on assembly, it will give you problems. Valves have to go back to the original location.

[Parmas]

Originally Posted by cali yaris

http://www.microimageonline.com/foru...lts-yaris.html

You posted that the link doesn't work for you, but I just tried it and it came up ok.

Still getting broken link ...

Although I got some news that AJUSA head bolts are similar to standard Bolts or else equal. I will be probably getting them custom made from DP.

What can you tell about porting? Is it worth doing it from experience? What is the average increased hp?

What about Knife edging crankshaft? What are the pros and cons of it?

What about doing upgraded sleeves? At what power they are really needed?

Come on is only Garm helping here... where are the experts

[CtrlAltDefeat]

http://downforeveryoneorjustme.com/i...manceparts.net works for me and downforeveryoneorjustme.com says its up

[cali yaris]

I sleeved my Yaris block because we knew we were going for 20+ pounds of boost.
I would sleeve it if you intend to throw 15+ at yours.

Porting/polishing increases airflow. The effect and increased hp is amplified when you throw boost at it (more air trying to pass through, obviously). I would do it.

I am using stock crankshaft, and I like the results I'm getting so far.

[rob323]

What can you tell about porting? Is it worth doing it from experience?

If you have the head apart, then you may as well do it. NA motors benefit from it more so than forced induction motors (the pressure from the turbo helps negate some of the inefficiencies in the intake).

What is the average increased hp?

Impossible to say, it varies with each and every car and how the porting is done.

What about Knife edging crankshaft? What are the pros and cons of it?

It reduces the reciprocal weight of the crank shaft, good for high revving motors (8000 rpm upwards). I wouldn't worry about it on your motor as you will have to fully rebalance the motor once you have done it. (Then again, if you are replacing the pistons, then you should fully rebalance the motor anyway).

What about doing upgraded sleeves? At what power they are really needed?

I haven't heard of anyone cracking a sleeve yet? Maybe some of the Scion boys have though as they have been putting boost through these motors longer than most?

[Parmas]

Ok so porting will be one on my list.... Then what about stock valves and springs? Are they capable of 20+ boost?

I made some more research on knife edging the crankshaft. They usually make it on Honda engines but since it doesn't cost that much I would probably do it.

RE: Sleeves... My Power intensions are somewhere near 300Hp. Considering that I am using a turbo GT28 and using street pump low grade octane fuel (Below 90) the engine would need about 25psi of boost to get into that range. The tuner said, if going to do sleeves, the pistons could need to be replaced to match new sleeves... so it would cost me a fortune to make this happen!

[changchewsoon]

hi parmas,

im too getting my head ported as well. at the same time, i fully agree with what garm said. the more air you could flow, the better. and results will be amplified when you boost it. you should go ahead and get a "head job" :)

im also having my cams welded and grinded too, and the valve springs will be changed as well.

as for the AJUSA bolts, i could only comment that the bolts are much more heavier than the stock ones. however, heavier does not mean they are better. i can only tell you this much, and until my cylinder head is back i don't have further inputs on that.

im currently keeping my crankshaft stock though, tuner did not recommend me to have them knife edged so i did not pursue that.

[Parmas]

Thanks for the info changchewsoon

What valve springs are you intending to use? Regarding cams I think I leave them stock don't want to mess everthing at once

RE AJUSA bolts, heavier doesn't meen better but the quality of metal used. Do you know if they match exactly the stock bolts? I mean no rethreading etc..

RE Knife edging crank, Did you asked your tuner the reason not doing it?

[cali yaris]

RE Knife edging crank, Did you asked your tuner the reason not doing it?

rob explained this point quite well.

I'm about to tune upwards of 25 psi, on stock crank and stock valve springs. I just don't see the need to spend money there when it's not necessary.

[Parmas]

What fuel octane are you using Garm?

[cali yaris]

91 with water/meth injection. Should be able to run 25 psi on pump gas.

[Parmas]

Originally Posted by cali yaris

91 with water/meth injection. Should be able to run 25 psi on pump gas.

I thought you have a better (directly from pump) octane than 91 there!