Yaris Sedan Deadening and Sound system upgrade - Page 84 - Toyota Yaris Forums

derickveliz2 · 08-25-2011, 02:48 AM

Quote:

Originally Posted by sqcomp

you have the L6's in? If so, take the crossover point down to 45 hz at 36 dB and the L6's to 45 at 24 dB. The TA on the sub (if it's in the rear) should be about 60-ish inches.

No I don't have the L6's in, I'm sure that is why the software is going that high!

But I'm saving this info once the time comes by! even though the way it sounds (Mid/bass) now was amazing for the DIYMeet members at the Massachusetts meet and had a chance to hear my set up, one of them had L6's and he was very much impressed,...

so... I guess it just gets better and better!

D.

derickveliz2 · 08-25-2011, 12:57 PM

Quote:

Originally Posted by sqcomp

D! Download a glitch song from Vibe Quad called, Funkwear. That is a bad ass track. Get it and get back to me after you hear it in the car.

Sounds AWESOME!

The Sub "shows off" I really like the IDQ12

Lows, slamming hard really nice, but at really high volume my left door (plastic panel vibrates and rattles)

This track has a very nice center image even without a singer!

The stage width goes from outside sail panel left to right, very interesting "wuogle" sound

Should I be looking for something else?

D.

sqcomp · 08-25-2011, 11:45 PM

There is a huge low end that can rumble the entire foundation of your vehicle...

Other than that, it's a simple "Whoa" type song.

The L6's in the door...If you trim out the circle in the panel you'll eliminate or reduce the rattle...

derickveliz2 · 08-26-2011, 01:17 AM

Quote:

Originally Posted by sqcomp

There is a huge low end that can rumble the entire foundation of your vehicle...

Other than that, it's a simple "Whoa" type song.

The L6's in the door...If you trim out the circle in the panel you'll eliminate or reduce the rattle...

Rumbles everything for sure, feels like 2 or 3 woofers in the trunk. The Lows are nice and tight, and the "Whoa" song sounds 3Dimensionally awesome!

I though about cutting a hole in the panel in front of the speaker! but just to be sure, do you mean exposing the speakers (Lows) and have eye contact with them? if so after using a router how do I finish and make it look good without doing another peace of art?

I would like to see the L6's move!

D.

derickveliz2 · 08-26-2011, 03:45 AM

I got this shot, that leaves the woofer exposed and brings more foot print area, with a little step foot rest area. Another idea[/B] with an inverted subwoofer firing into the box! could be next! I still think that I should wait for the port and get an idea on how big are the inside/outside flares!

Disregard the I6SW in this picture it's only holding the inclined board that holds the popcorn and

D.

derickveliz2 · 09-01-2011, 03:37 AM

Ok, the port came in a little before Irene, we are ok, and I had some time to think!

After some ergonomic issues about the sub box I also came with other option that runs the sub facing down and the 16 inches of port in a straight configuration instead of using the 90 degree elbow, I have 2 shots with my 10 size working shoes and my wife's shoes as well.

When I sit down a more comfortable position and natural posture of my feet. and the 10 liters of Popcorn shows that we are ok in the internal volume.

I like this option, not only because it's ergonomics but puts the port facing forward more in the center of the car, the woofer it's protected (I rather have it showing off, but it would be in the way of the Heat/AC for the feet), I can still move the seat all the way forward.

Less writing and more pictures:

D.

derickveliz2 · 09-01-2011, 02:12 PM

Quote:

Originally Posted by TOLMACH

Is there a way to use space under the glove box? (or may be sacrifice a glove box?)

I'm using the space under the glove box, and I don't want to give up the glove box either, too much building and there is not a lot of space there, besides that I would need to reinforce the area due to the extra weight from the sub + enclosure.

I rather keep it simply

derickveliz2 · 09-01-2011, 02:42 PM

Quote:

Originally Posted by TOLMACH

Is there a way to use space under the glove box? (or may be sacrifice a glove box?)

TOLMACH,
do you have a picture of your yaris showing some landscape from over there?

D.

derickveliz2 · 09-01-2011, 02:59 PM

Quote:

Originally Posted by TOLMACH

Mine is HB and completely untouched at the moment.. Do you still want the picture?

Yeah! what I really would like to see is your Yaris in Moscow and the surroundings

D.

sqcomp · 09-01-2011, 08:49 PM

TOLM...

WTF?!? I was just up in BC on august 20-21st! Where in BC are you?

derickveliz2 · 09-02-2011, 12:20 AM

We almost forgot about Deadening and Diesel trucks!

check out this video:

LINK to VIDEO click HERE

or copy/paste this:

http://youtu.be/RO2e16sQMb8

D.

derickveliz2 · 09-02-2011, 02:11 AM

This is a very interesting option, even can't really tell on the pictures the gain in space specially stretching your legs it's a plus in this option, on the negative I can't push the seat all the way forward, just a little bit. The internal volume it's "ok" too!

Another good thing is that I could steel go with the L6's in kick panels! if the doors don't like them.

D.

sqcomp · 09-02-2011, 12:17 PM

@ Tolmach - I'm not showing the car anymore this year. I've got too much to do with the install. Now that I know it can win, I'm making it better.

Our last show was at Keith McCumber's IASCA Canadian Western Regionals at the Canadian Tire in Coquitlam.

The next show will probably be down here in the states next year.

Oh! Derick! What else could I possibly do to the car (except for rims and lowering)? MWAHAHA!!!! Think train horns!

http://www.hornblasters.com/video.php?video=62

I was forced off the road yesterday by a Ford truck. MF'r thought it was funny until I came out of the car and put a big dent in the side of his truck...POS wouldn't get out and answer for pretty much trying to kill me...

Even with those three tone Hella horns...I need to go bigger with this small car...

sickpuppy1 · 09-04-2011, 10:52 PM

I know a guy with a train horn under the bed of his S10. He has it "bagged" too. We mentioned he probably gets alot of attention with it lowered like that. He says, this is what gets their attention, and reaches in and toots that horn......Scared the crap out of all of us,lol

derickveliz2 · 09-05-2011, 12:11 AM

Quote:

Originally Posted by sqcomp

Oh! Derick! What else could I possibly do to the car (except for rims and lowering)? MWAHAHA!!!! Think train horns!

What about eye lids, SSK, and train horns.... LOL

D.

sqcomp · 09-05-2011, 02:50 AM

Since this weekend is a holiday...we have to start on it next Monday. Damn!

derickveliz2 · 09-05-2011, 11:26 PM

Long weekend @ Laconia NH just relaxing with family.

Last week coming back from work I was thinking what if... I had the port in 2 sections using the 90 degree elbow...

The picture below shows what I was thinking, consider the port to be 3" shorter using the elbow. Today I was playing around with it and it's a really good option,
I still have to figure out how much internal volume is, my guess is that it's pretty close!

We'll see:

Sorry for the crappy cellphone picture :(

sqcomp · 09-13-2011, 11:36 AM

^New horns

^New horns. You can see the Hella three tone and the stock horn. No comparing these whatsoever...

Derick...I'll put up some video when I get some shot. Needless to say, these are LOUD!!!

08-25-2011, 11:45 PM	#1497
sqcomp Roadrunner Jr. View User's Garage Drives: 2007 Yaris S Join Date: Jan 2007 Location: Back at home Posts: 2,609	There is a huge low end that can rumble the entire foundation of your vehicle... Other than that, it's a simple "Whoa" type song. The L6's in the door...If you trim out the circle in the panel you'll eliminate or reduce the rattle... __________________ “To argue with a person who has renounced the use of reason is like administering medicine to the dead.” ― Thomas Paine

08-26-2011, 03:45 AM	#1499
derickveliz2 View User's Garage Drives: Yaris Sedan "S" Join Date: Oct 2008 Location: Central, MA Posts: 2,722	I got this shot, that leaves the woofer exposed and brings more foot print area, with a little step foot rest area. Another idea[/B] with an inverted subwoofer firing into the box! could be next! I still think that I should wait for the port and get an idea on how big are the inside/outside flares! Disregard the I6SW in this picture it's only holding the inclined board that holds the popcorn and D. __________________ . My system may not blow your ears, but it will sweeten your senses. CLA 250, 4MATIC

09-01-2011, 03:37 AM	#1500
derickveliz2 View User's Garage Drives: Yaris Sedan "S" Join Date: Oct 2008 Location: Central, MA Posts: 2,722	Ok, the port came in a little before Irene, we are ok, and I had some time to think! After some ergonomic issues about the sub box I also came with other option that runs the sub facing down and the 16 inches of port in a straight configuration instead of using the 90 degree elbow, I have 2 shots with my 10 size working shoes and my wife's shoes as well. When I sit down a more comfortable position and natural posture of my feet. and the 10 liters of Popcorn shows that we are ok in the internal volume. I like this option, not only because it's ergonomics but puts the port facing forward more in the center of the car, the woofer it's protected (I rather have it showing off, but it would be in the way of the Heat/AC for the feet), I can still move the seat all the way forward. Less writing and more pictures: D. __________________ . My system may not blow your ears, but it will sweeten your senses. CLA 250, 4MATIC

09-01-2011, 08:49 PM	#1504
sqcomp Roadrunner Jr. View User's Garage Drives: 2007 Yaris S Join Date: Jan 2007 Location: Back at home Posts: 2,609	TOLM... WTF?!? I was just up in BC on august 20-21st! Where in BC are you? __________________ “To argue with a person who has renounced the use of reason is like administering medicine to the dead.” ― Thomas Paine

09-02-2011, 12:20 AM	#1505
derickveliz2 View User's Garage Drives: Yaris Sedan "S" Join Date: Oct 2008 Location: Central, MA Posts: 2,722	We almost forgot about Deadening and Diesel trucks! check out this video: LINK to VIDEO click HERE or copy/paste this: http://youtu.be/RO2e16sQMb8 D. __________________ . My system may not blow your ears, but it will sweeten your senses. CLA 250, 4MATIC

09-02-2011, 02:11 AM	#1506
derickveliz2 View User's Garage Drives: Yaris Sedan "S" Join Date: Oct 2008 Location: Central, MA Posts: 2,722	This is a very interesting option, even can't really tell on the pictures the gain in space specially stretching your legs it's a plus in this option, on the negative I can't push the seat all the way forward, just a little bit. The internal volume it's "ok" too! Another good thing is that I could steel go with the L6's in kick panels! if the doors don't like them. D. __________________ . My system may not blow your ears, but it will sweeten your senses. CLA 250, 4MATIC

09-02-2011, 12:17 PM	#1507
sqcomp Roadrunner Jr. View User's Garage Drives: 2007 Yaris S Join Date: Jan 2007 Location: Back at home Posts: 2,609	@ Tolmach - I'm not showing the car anymore this year. I've got too much to do with the install. Now that I know it can win, I'm making it better. Our last show was at Keith McCumber's IASCA Canadian Western Regionals at the Canadian Tire in Coquitlam. The next show will probably be down here in the states next year. Oh! Derick! What else could I possibly do to the car (except for rims and lowering)? MWAHAHA!!!! Think train horns! http://www.hornblasters.com/video.php?video=62 I was forced off the road yesterday by a Ford truck. MF'r thought it was funny until I came out of the car and put a big dent in the side of his truck...POS wouldn't get out and answer for pretty much trying to kill me... Even with those three tone Hella horns...I need to go bigger with this small car... __________________ “To argue with a person who has renounced the use of reason is like administering medicine to the dead.” ― Thomas Paine

09-04-2011, 10:52 PM	#1508
sickpuppy1 Drives: 2010 Yaris Sedan Join Date: Feb 2010 Location: Kansas Posts: 871	I know a guy with a train horn under the bed of his S10. He has it "bagged" too. We mentioned he probably gets alot of attention with it lowered like that. He says, this is what gets their attention, and reaches in and toots that horn......Scared the crap out of all of us,lol __________________

09-05-2011, 02:50 AM	#1510
sqcomp Roadrunner Jr. View User's Garage Drives: 2007 Yaris S Join Date: Jan 2007 Location: Back at home Posts: 2,609	Since this weekend is a holiday...we have to start on it next Monday. Damn! __________________ “To argue with a person who has renounced the use of reason is like administering medicine to the dead.” ― Thomas Paine

09-05-2011, 11:26 PM	#1511
derickveliz2 View User's Garage Drives: Yaris Sedan "S" Join Date: Oct 2008 Location: Central, MA Posts: 2,722	Long weekend @ Laconia NH just relaxing with family. Last week coming back from work I was thinking what if... I had the port in 2 sections using the 90 degree elbow... The picture below shows what I was thinking, consider the port to be 3" shorter using the elbow. Today I was playing around with it and it's a really good option, I still have to figure out how much internal volume is, my guess is that it's pretty close! We'll see: Sorry for the crappy cellphone picture :( __________________ . My system may not blow your ears, but it will sweeten your senses. CLA 250, 4MATIC

09-13-2011, 11:36 AM	#1512
sqcomp Roadrunner Jr. View User's Garage Drives: 2007 Yaris S Join Date: Jan 2007 Location: Back at home Posts: 2,609	^New horns ^New horns. You can see the Hella three tone and the stock horn. No comparing these whatsoever... Derick...I'll put up some video when I get some shot. Needless to say, these are LOUD!!! __________________ “To argue with a person who has renounced the use of reason is like administering medicine to the dead.” ― Thomas Paine

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
sound deadening: sq footage amount for 3dr	goku87	In Car Entertainment + Electronics (audio / video / alarm)	29	11-14-2013 01:37 PM
2007 Yaris S Sound Deadening	sqcomp	In Car Entertainment + Electronics (audio / video / alarm)	70	12-13-2010 08:40 PM
Sound deadening	06vitzRS	General Yaris / Vitz Discussion	10	05-05-2010 02:51 PM
Sedan Door Panel Deadening	sqcomp	In Car Entertainment + Electronics (audio / video / alarm)	42	06-01-2009 03:47 PM