 |
 |
|
|
04-06-2013, 04:50 AM
|
#1 |
|
PEEWEE1
Drives: 2009 yaris s sedan Join Date: Apr 2013
Location: New York
Posts: 55
|
PCV valve over tight
My pcv valve is sooooo tight i'm afraid I'm going to "tear" or damage it when trying to remove it. All I've tried is the 3/8 ratchet and socket. I thought the engine was going to be pulled out when I tried to loosen the valve. Could I use maybe some penetrating oil, or "heat" from a torch? This s.o.b. is !!!! Thanks for any ideas.......
|
|
|
|
04-06-2013, 10:06 AM
|
#2 |
|
Proud Toyota Owner
Drives: 2008 Yaris HB Join Date: Mar 2013
Location: Florida
Posts: 21
|
I just changed mine as well, At first I used a 3/8 ratchet and it felt like it was welded on. Step it up to a 1/2 ratchet with a deep wall socket and it'll be easier.
|
|
|
|
|
04-06-2013, 11:21 AM
|
#3 |
|
PEEWEE1
Drives: 2009 yaris s sedan Join Date: Apr 2013
Location: New York
Posts: 55
|
pcv
I took your advise with 1/2 inch ratchet,Plus a nice steel pipe as a breaker bar, I heard a nice snap and it loosened up. Cleaned it out with gunk and reinstalled it. Thanks for the help.
|
|
|
|
|
04-08-2013, 12:11 AM
|
#4 |
  Drives: 08 Yaris sedan auto / Fit auto Join Date: Oct 2009
Location: northeast
Posts: 2,897
|
Checked it for the sedan . Had oil in it . Still hear the rattle from within , so placed it back in . Should it be cleaned or recheck later ?
Last edited by Hershey; 04-09-2013 at 12:01 PM. |
|
|
|
|
04-09-2013, 06:08 AM
|
#5 |
|
PEEWEE1
Drives: 2009 yaris s sedan Join Date: Apr 2013
Location: New York
Posts: 55
|
pcv
While you have it out why not clean it with a little Gunk.
|
|
|
|
|
04-09-2013, 12:02 PM
|
#6 |
|
Drives: 08 Yaris sedan auto / Fit auto Join Date: Oct 2009
Location: northeast
Posts: 2,897
|
Don't have any .
|
|
|
|
|
04-09-2013, 12:34 PM
|
#7 | |
Drives: 08Yaris2D, 88LandCruiser. Join Date: Jan 2013
Location: Alameda,Ca.
Posts: 476
|
Quote:
__________________
Give a man a fish, and he'll eat for a day. Sell a man a fish, and you'll both eat for a day. 
|
|
|
|
|
|
08-31-2013, 09:16 PM
|
#8 |
Drives: toyota yaris yrs Join Date: Jun 2007
Location: Sydney
Posts: 642
|
Mine came off easier than i thought. I checked it and didn't see any build up at all.Did the shake test and it was rattling fine inside.But decided to give it clean up with carb cleaner. I also did the throttle body.
Maybe your turning it the wrong way? |
|
|
|
|
09-01-2013, 10:28 PM
|
#9 |
|
Drives: 2009 yaris 2 door Join Date: Feb 2013
Location: richmond TX.
Posts: 235
|
anti sieze lube
Since you have it off now put some anti-sieze on the threads for next time. Not too much just a little dib on the threads and I guarantee it'll come out real easy a year from now.
|
|
|
|
 |
|
|
Similar Threads
|
||||
| Thread | Thread Starter | Forum | Replies | Last Post |
| PCV Valve | SonicGuppy | DIY / Maintenance / Service | 4 | 11-12-2014 10:03 AM |
| PCV valve question | window_lee | DIY / Maintenance / Service | 31 | 10-22-2014 05:05 PM |
| PCV Valve Replacement | devinlamothe | DIY / Maintenance / Service | 27 | 03-17-2013 12:06 AM |
| NEED ENGINE CHECK LIGHT CODE LIST | Attitude | Forced Induction Forum | 12 | 04-11-2011 07:38 PM |
| Two different PCV valve Part#s for Yaris? | auxmike | DIY / Maintenance / Service | 6 | 03-18-2011 09:55 AM |
Linear Mode
