My 2011 Vitz - Page 26 - Toyota Yaris Forums

TerenceCruz · 08-25-2015, 10:05 PM

Quote:

Originally Posted by coheed

Don't get me wrong, I like the control I have over my height. I just wish I could pin down my leaking lol. Also I wish it aired out a little bit quicker. The exhaust port on the manual valves are 1/8" and it takes so long for the front to go down. And I run twice the air in the front as the rear, so the back of the car is down 5 sec before the front.

I'm liking the 16's on your car more and more man. You're convincing me that static Yarii need 16's.

Ahhh very true, my friend said the same, we parked in the garage and I was like what're you doing, and he said "Still airing out" hahaha it was hella funny. The port can't go any bigger? And thanks a lot man, I feel the same way. I'm just looking towards a different type of wheel now. Still 16s, maybe 16x9 but I'm just over the mesh look haha.

yarisugi · 08-26-2015, 01:18 PM

@coheed - 1/8" lines are tiny! After you find your leak, try 1/4" at least. Not more than 3/8" though. Should help speed up your lowering/raising.

@TC- New wheels already? Curious what you have in mind...

coheed · 08-26-2015, 09:29 PM

Quote:

Originally Posted by TerenceCruz

Ahhh very true, my friend said the same, we parked in the garage and I was like what're you doing, and he said "Still airing out" hahaha it was hella funny. The port can't go any bigger? And thanks a lot man, I feel the same way. I'm just looking towards a different type of wheel now. Still 16s, maybe 16x9 but I'm just over the mesh look haha.

I don't know if it could go any bigger. I would try drilling it out a bit, but at $15 and not being able to buy one locally, I think I'll leave it and deal with airing out slowly lol

Quote:

Originally Posted by yarisugi

@coheed - 1/8" lines are tiny! After you find your leak, try 1/4" at least. Not more than 3/8" though. Should help speed up your lowering/raising.

@TC- New wheels already? Curious what you have in mind...

No my lines are 1/4", but the air exhaust port on the back of the manual paddle valves are 1/8". My raise time is great, its the lowering that takes forever.

TerenceCruz · 08-26-2015, 09:45 PM

Quote:

Originally Posted by yarisugi

@coheed - 1/8" lines are tiny! After you find your leak, try 1/4" at least. Not more than 3/8" though. Should help speed up your lowering/raising.

@TC- New wheels already? Curious what you have in mind...

I was trying to avoid the mesh look, but I got a good offer for a trade for some brand new 16x9s so i'll post on here with pics if it goes through! Polished lips with white faces :) Still reps unfortunately, but ill fake the funk til i graduate school and get something nicer :)

TerenceCruz · 09-06-2015, 11:45 PM

Trade didn't go through, but I ended up finding some other JNCs in 16x9 that I loved. They will be arriving in a few days, and I'll mount the same tires I had on the BBS RS reps. Since they will be 16x9 I think the 195/45s will be the perfect stretch. Pics will be up when I get them on! :)

TerenceCruz · 09-11-2015, 07:28 PM

As promised. New wheels are on! 16x9 +25 JNC014 (Sorry they're still reps lol but I love them) on 195/45s. I have 10mm spacers in the rear. So +15 in the rear :) Hate how it looks high from the rear. Lol. There are some rubbing issues, so I will have to pull/flare the fenders out even more.

coheed · 09-12-2015, 02:53 PM

Seriously it looks awesome man. Props.

And you'll never get over thinking the Yaris looks high in the rear. I think mine looks high in the rear aired out lol

TerenceCruz · 09-12-2015, 04:30 PM

Quote:

Originally Posted by coheed

Seriously it looks awesome man. Props.

And you'll never get over thinking the Yaris looks high in the rear. I think mine looks high in the rear aired out lol

Much love bro, thank you! And lol that's so irritating. Can they make a rear lip or something easier to get.. Smh haha.

TerenceCruz · 09-12-2015, 06:13 PM

More pictures with the homies recently acquired EG8 while he works on his GSR 4 door.

Still scraping pretty tough, probably gona add a tad bit more camber in the front. I love how she sits though!

ern-diz · 09-14-2015, 02:07 AM

Super clean

TerenceCruz · 09-15-2015, 12:03 AM

Quote:

Originally Posted by ern-diz

Super clean

Thanks man!

Supra_Yaris · 10-27-2015, 04:47 PM

How many washers did you you to achieve that much rear camber? And about how many degrees of camber do you have in the rear?

TerenceCruz · 10-27-2015, 05:40 PM

Quote:

Originally Posted by Supra_Yaris

How many washers did you you to achieve that much rear camber? And about how many degrees of camber do you have in the rear?

Used 3 grade 8 washers per lower bolt on each side. So i have a total of 12 washers. I'm running about -3 camber. Each washer used is supposed to be -1 degree of camber.

Supra_Yaris · 10-27-2015, 07:12 PM

Quote:

Originally Posted by TerenceCruz

Used 3 grade 8 washers per lower bolt on each side. So i have a total of 12 washers. I'm running about -3 camber. Each washer used is supposed to be -1 degree of camber.

Great! Just what I was looking for. Thanks!

aspro · 10-27-2015, 07:16 PM

This car is stupid, retarded shlammed.... I love it haha

aspro · 10-27-2015, 07:20 PM

Also, if youre looking to get the rear end lower to the ground, why dont you source a rear toyota RS lip for the 09-11 yaris'... That mkght get you a few more inches to the ground without have to go lower. Heres what the lip looks like...

TerenceCruz · 10-28-2015, 04:13 PM

Quote:

Originally Posted by Supra_Yaris

Great! Just what I was looking for. Thanks!

No worries man!

Quote:

Originally Posted by aspro

This car is stupid, retarded shlammed.... I love it haha

Hahaha thanks man! Im also looking for the whole kit actually. I want to source a front, rear, and side skirts. I'd love to find it.

TerenceCruz · 11-02-2015, 10:26 PM

Aspro, I also want your exhaust so bad haha. I would trade cars with you instantly hahaha.

09-11-2015, 07:28 PM	#456
TerenceCruz Drives: 2011 Toyota Yaris Join Date: Feb 2013 Location: Cali Posts: 725	As promised. New wheels are on! 16x9 +25 JNC014 (Sorry they're still reps lol but I love them) on 195/45s. I have 10mm spacers in the rear. So +15 in the rear :) Hate how it looks high from the rear. Lol. There are some rubbing issues, so I will have to pull/flare the fenders out even more. Last edited by TerenceCruz; 09-11-2015 at 07:39 PM.

09-12-2015, 02:53 PM	#457
coheed Drives: 08 BB LB Join Date: Dec 2008 Location: Maiden, NC Posts: 785	Seriously it looks awesome man. Props. And you'll never get over thinking the Yaris looks high in the rear. I think mine looks high in the rear aired out lol __________________ Too much of car culture is people taking things too seriously and not enjoying it for what it is.

10-27-2015, 07:16 PM	#465
aspro Drives: 2011 Yaris RS 5 door 5 spd Join Date: Aug 2012 Location: Toronto, Canada Posts: 449	This car is stupid, retarded shlammed.... I love it haha __________________ TRD sway bar, h&r coilovers, tanabe strut tower bar, konig feather, bfg sport comp 2, MI intake manifold, aem cai, dc header, trd catback, MI crank pulley, trd short shift kit, phillips hid kit, morimoto led fogs, parrot navi indash, alpine 6.5 speakers, alpine amp, alpine reverse camera, led interior lights, thule roof racks, netz badges...

10-27-2015, 07:20 PM	#466
aspro Drives: 2011 Yaris RS 5 door 5 spd Join Date: Aug 2012 Location: Toronto, Canada Posts: 449	Also, if youre looking to get the rear end lower to the ground, why dont you source a rear toyota RS lip for the 09-11 yaris'... That mkght get you a few more inches to the ground without have to go lower. Heres what the lip looks like... __________________ TRD sway bar, h&r coilovers, tanabe strut tower bar, konig feather, bfg sport comp 2, MI intake manifold, aem cai, dc header, trd catback, MI crank pulley, trd short shift kit, phillips hid kit, morimoto led fogs, parrot navi indash, alpine 6.5 speakers, alpine amp, alpine reverse camera, led interior lights, thule roof racks, netz badges...

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
2010 Vitz RS Modellista Completed Car	Vitz Rs Modellista	Photo-Video-Media Gallery	38	11-18-2014 01:25 PM
2012 Vitz from the 2011 Tokyo Auto Salon	CTScott	Third Gen Yaris General Discussion	14	02-10-2011 09:06 AM
Is UA-NCP13 1.5L Manual Trans a Vitz RS?	WesSunday	General Yaris / Vitz Discussion	1	11-28-2010 11:47 AM
Newly refreshed 2011 Toyota Corolla	Kal-El	Off-topic / Other Cars / Everything else Discussions	23	11-27-2010 01:57 PM
A German Yaris/Vitz/Echo ;)	we-to-11	Photo-Video-Media Gallery	5	06-27-2007 09:26 PM

08-26-2015, 01:18 PM	#452
yarisugi やりすぎだ～ View User's Garage Drives: Me: Nuts: Join Date: Nov 2008 Location: ハワイ Posts: 2,041	@coheed - 1/8" lines are tiny! After you find your leak, try 1/4" at least. Not more than 3/8" though. Should help speed up your lowering/raising. @TC- New wheels already? Curious what you have in mind...

09-06-2015, 11:45 PM	#455
TerenceCruz Drives: 2011 Toyota Yaris Join Date: Feb 2013 Location: Cali Posts: 725	Trade didn't go through, but I ended up finding some other JNCs in 16x9 that I loved. They will be arriving in a few days, and I'll mount the same tires I had on the BBS RS reps. Since they will be 16x9 I think the 195/45s will be the perfect stretch. Pics will be up when I get them on! :)

09-12-2015, 06:13 PM	#459
TerenceCruz Drives: 2011 Toyota Yaris Join Date: Feb 2013 Location: Cali Posts: 725	More pictures with the homies recently acquired EG8 while he works on his GSR 4 door. Still scraping pretty tough, probably gona add a tad bit more camber in the front. I love how she sits though!

09-14-2015, 02:07 AM	#460
ern-diz View User's Garage Drives: 2007 Liftback Join Date: Sep 2007 Location: CA all day Posts: 3,794	Super clean

10-27-2015, 04:47 PM	#462
Supra_Yaris Logan Drives: 2009 Yaris Liftback Base MT Join Date: Jan 2015 Location: Denton, TX Posts: 107	How many washers did you you to achieve that much rear camber? And about how many degrees of camber do you have in the rear?

11-02-2015, 10:26 PM	#468
TerenceCruz Drives: 2011 Toyota Yaris Join Date: Feb 2013 Location: Cali Posts: 725	Aspro, I also want your exhaust so bad haha. I would trade cars with you instantly hahaha.