My 2011 Vitz - Page 29 - Toyota Yaris Forums

TerenceCruz · 01-28-2016, 11:17 AM

Quote:

Originally Posted by tadakun

I plan on stayin 15s until I can afford a good set of wheels. I'm currently running the stock size tires until I wear them out. Then I'll change to a lower profile. You know....because more low. :D thanks for the heads up on the 3mm difference. I'll be getting 5mm and 8mm spacers after I slap on the camber plate.

Sweet definitely a good plan! I'm actually going to be taking off my 10mm PG hub spacers because the poke is actually a little too much and I need some clearance to go lower. So at the end I'll just be running the camber shims, with a 8mm spacer on the driver rear, and 5mm spacer in the passenger rear.

ern-diz · 01-28-2016, 11:54 AM

That 3rd annual Initial D meet vid was an enjoyable watch. Some really cool cars. Thanks for the share.

TerenceCruz · 01-29-2016, 06:55 PM

Quote:

Originally Posted by ern-diz

That 3rd annual Initial D meet vid was an enjoyable watch. Some really cool cars. Thanks for the share.

No problem, glad you enjoyed the video!

TerenceCruz · 02-04-2016, 06:39 PM

Some more awesome pictures I found of my car from the meet :)

12647817_902597476515734_1457751552_n by Tj Cruz, on Flickr

12648133_902597486515733_1566527378_n by Tj Cruz, on Flickr

12647850_902597503182398_569264213_n by Tj Cruz, on Flickr

12595940_902585929850222_973851448_n by Tj Cruz, on Flickr

12647712_902585949850220_481613731_n by Tj Cruz, on Flickr

tadakun · 02-05-2016, 12:12 PM

that rear poke bruh. love it.

TerenceCruz · 02-05-2016, 04:57 PM

Quote:

Originally Posted by tadakun

that rear poke bruh. love it.

Thank you man! I love it too, but the pictures actually didn't do it justice. It poked out a lot and all I could smell during the drive was burning tire! Hahaha. So, I took out the 10mm spacers (they are now for sale) So i'm just running camber shims in the rear, and I'm waiting on some 5mm spacers. Don't worry, the poke is still there

yarisugi · 02-05-2016, 05:03 PM

I LOVE

!!

TerenceCruz · 02-05-2016, 06:01 PM

Quote:

Originally Posted by yarisugi

I LOVE

!!

Sugi can I have your air ride, wheels, and car please? Thank you! Can you post on here some pics of your car? I miss it and it gives me motivation ;) hahahaha

ern-diz · 02-05-2016, 06:42 PM

Quote:

Originally Posted by TerenceCruz

Sugi can I have your air ride, wheels, and car please? Thank you! Can you post on here some pics of your car? I miss it and it gives me motivation ;) hahahaha

+1

TerenceCruz · 02-07-2016, 07:06 PM

Happy to say I finally pulled the trigger and purchased a used TRD axle back :D It just need a good polish but I think it's still in good condition! Will post pictures once it arrives and is installed! ;)

tadakun · 02-08-2016, 11:36 AM

Quote:

Originally Posted by yarisugi

I LOVE

!!

poke game on point. gawd that looks so good.

tadakun · 02-08-2016, 11:37 AM

Quote:

Originally Posted by TerenceCruz

Happy to say I finally pulled the trigger and purchased a used TRD axle back :D It just need a good polish but I think it's still in good condition! Will post pictures once it arrives and is installed! ;)

awesome! can't wait to see.

We need a general discussion just for the fitment gang around these parts. haha.

TerenceCruz · 02-08-2016, 11:50 AM

Quote:

Originally Posted by tadakun

awesome! can't wait to see.

We need a general discussion just for the fitment gang around these parts. haha.

I totally agree lol

TerenceCruz · 02-11-2016, 05:09 PM

As promised ;) TRD axle back arrived and was installed yesterday!

12696021_908297325945749_1462208345_n by Tj Cruz, on Flickr

12713994_908297289279086_1244371052_n by Tj Cruz, on Flickr

Could not be ANY happier of how nice it fits under there. It has so much clearance which I needed for the cars current height. Sounds amazing too. I previously had a tanabe medalion touring axle back, but it hung so low I knew I would damage it. So I sold it before anything could happen.

12721700_908300569278758_920895044_n by Tj Cruz, on Flickr

12714344_908300582612090_1778355015_n by Tj Cruz, on Flickr

My only complaint has nothing to do with the exhaust at all, but instead it's the freakin heat shield that detached somehow (probably when I hit a fat bump) And now it makes an annoying rattling sound when it comes into contact with the piping. Anyone have any idea how that was originally attached? I tried 3M tape but it only worked for a little bit. Any help would be greatly appreciated. Thank you guys, and enjoy!

WeeYari · 02-11-2016, 05:38 PM

Quote:

Originally Posted by TerenceCruz

Anyone have any idea how that was originally attached? I tried 3M tape but it only worked for a little bit. Any help would be greatly appreciated. Thank you guys, and enjoy!

A large plastic clip-in retainer/plug goes in there.

TerenceCruz · 02-11-2016, 05:49 PM

Quote:

Originally Posted by WeeYari

A large plastic clip-in retainer/plug goes in there.

Ahh gotcha! I should have measured the hole size while I was under there. I'll visit Lowes or Home Depot and see if I can find something for it. Thanks!

coheed · 02-12-2016, 02:41 AM

Mines still zip tied in place. Been like that for about 2 years now lol

TerenceCruz · 02-12-2016, 02:18 PM

Quote:

Originally Posted by coheed

Mines still zip tied in place. Been like that for about 2 years now lol

How'd you zip tie that? Lol I was thinking about doing that but didn't know where! Lol

02-07-2016, 07:06 PM	#514
TerenceCruz Drives: 2011 Toyota Yaris Join Date: Feb 2013 Location: Cali Posts: 725	Happy to say I finally pulled the trigger and purchased a used TRD axle back :D It just need a good polish but I think it's still in good condition! Will post pictures once it arrives and is installed! ;) Last edited by TerenceCruz; 02-08-2016 at 12:52 AM.

02-12-2016, 02:41 AM	#521
coheed Drives: 08 BB LB Join Date: Dec 2008 Location: Maiden, NC Posts: 785	Mines still zip tied in place. Been like that for about 2 years now lol __________________ Too much of car culture is people taking things too seriously and not enjoying it for what it is.

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
2010 Vitz RS Modellista Completed Car	Vitz Rs Modellista	Photo-Video-Media Gallery	38	11-18-2014 01:25 PM
2012 Vitz from the 2011 Tokyo Auto Salon	CTScott	Third Gen Yaris General Discussion	14	02-10-2011 09:06 AM
Is UA-NCP13 1.5L Manual Trans a Vitz RS?	WesSunday	General Yaris / Vitz Discussion	1	11-28-2010 11:47 AM
Newly refreshed 2011 Toyota Corolla	Kal-El	Off-topic / Other Cars / Everything else Discussions	23	11-27-2010 01:57 PM
A German Yaris/Vitz/Echo ;)	we-to-11	Photo-Video-Media Gallery	5	06-27-2007 09:26 PM

01-28-2016, 11:54 AM	#506
ern-diz View User's Garage Drives: 2007 Liftback Join Date: Sep 2007 Location: CA all day Posts: 3,794	That 3rd annual Initial D meet vid was an enjoyable watch. Some really cool cars. Thanks for the share.

02-04-2016, 06:39 PM	#508
TerenceCruz Drives: 2011 Toyota Yaris Join Date: Feb 2013 Location: Cali Posts: 725	Some more awesome pictures I found of my car from the meet :) 12647817_902597476515734_1457751552_n by Tj Cruz, on Flickr 12648133_902597486515733_1566527378_n by Tj Cruz, on Flickr 12647850_902597503182398_569264213_n by Tj Cruz, on Flickr 12595940_902585929850222_973851448_n by Tj Cruz, on Flickr 12647712_902585949850220_481613731_n by Tj Cruz, on Flickr

02-05-2016, 12:12 PM	#509
tadakun Drives: 09 Yaris Join Date: Jul 2010 Location: Oregon Posts: 123	that rear poke bruh. love it.

02-05-2016, 05:03 PM	#511
yarisugi やりすぎだ～ View User's Garage Drives: Me: Nuts: Join Date: Nov 2008 Location: ハワイ Posts: 2,041	I LOVE !!

02-11-2016, 05:09 PM	#518
TerenceCruz Drives: 2011 Toyota Yaris Join Date: Feb 2013 Location: Cali Posts: 725	As promised ;) TRD axle back arrived and was installed yesterday! 12696021_908297325945749_1462208345_n by Tj Cruz, on Flickr 12713994_908297289279086_1244371052_n by Tj Cruz, on Flickr Could not be ANY happier of how nice it fits under there. It has so much clearance which I needed for the cars current height. Sounds amazing too. I previously had a tanabe medalion touring axle back, but it hung so low I knew I would damage it. So I sold it before anything could happen. 12721700_908300569278758_920895044_n by Tj Cruz, on Flickr 12714344_908300582612090_1778355015_n by Tj Cruz, on Flickr My only complaint has nothing to do with the exhaust at all, but instead it's the freakin heat shield that detached somehow (probably when I hit a fat bump) And now it makes an annoying rattling sound when it comes into contact with the piping. Anyone have any idea how that was originally attached? I tried 3M tape but it only worked for a little bit. Any help would be greatly appreciated. Thank you guys, and enjoy!